Nexgrill 720-0125-LP manual Installer Final, Before Testing, To Test, Gas flow check

Page 15
BEFORE TESTING

BEFORE TESTING

Make sure that all packing material is removed from the grill including the burner tie-down straps.

DO NOT SMOKE WHILE LEAK TESTING.

NEVER LEAK TEST WITH AN OPEN FLAME.

Make a soap solution of one part liquid detergent and one part water. You will need a spray bottle, brush, or rag to apply the solution to the fittings. For the initial leak test, make sure the L.P. cylinder is full.

TO TEST

Make sure all control valves are in the “OFF” position. Turn the gas supply on. Check all connections from the L.P. cylinder up to and including the connection to the manifold pipe assembly (the pipe that goes to the burners). Soap bubbles will appear where a leak is present. If a leak is present, immediately turn off the gas supply, tighten any leaking fittings, turn gas on, and recheck. Should the gas continue to leak from any or all of the fittings, turn off the gas supply, and contact our customer service at 1-800-913-8999.

Only those parts recommended by the manufacturer should be used on the grill. Substitution will void the warranty. Do not use the grill until all connections have been checked and do not leak.

Gas flow check:

Each grill burner is tested and adjusted at the factory prior to shipment; however, variations in the

local gas supply may make it necessary to adjust the burners. The flames of the burners should be visually checked.

Flames should be blue and stable with no yellow tips, excessive noise or lifting. If any of these conditions exist, check to see if the air shutter or burner ports are blocked by dirt, debris, spider webs, etc. If you have any questions regarding flame stability, please call customer service 1-800- 913-8999.

ALWAYS CHECK FOR LEAKS AFTER EVERY L.P. TANK CHANGE

Check all gas supply fittings for leaks before each use. It is handy to keep a spray bottle of soapy water near the shut-off valve of the gas supply line. Spray all the fittings. Bubbles indicate leaks.

Disconnected L.P. cylinders must have threaded valve plugs tightly installed, and must not be stored in a building, garage or any other enclosed area.

The gas must be turned off at the supply cylinder when the unit is not in use.

If the appliance is stored indoors the cylinder must be disconnected and removed from the appliance. Cylinders must be stored outdoors in a well-ventilated area out of the reach of children.

.

INSTALLER FINAL

ˆSpecified clearance maintained 24” from combustibles.

ˆAll internal packaging removed.

ˆKnobs turn freely.

ˆBurners are tight and sitting properly on orifices.

ˆPressure regulator connected and set for 11.2” W.C. L.P. gas. Gas connections to grill using

hose & regulator assembly provided (pre-set for 11.0” water column).

ˆUnit tested and free of leaks.

ˆUser informed of gas supply shut off valve location.

USER, PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

PROPANE CYLINDER CAUTIONS

a)Do Not store a spare LP-gas cylinder under or near this appliance.

b)NEVER fill the cylinder beyond 80 percent full.

c)If the information in “a” and “b” is not followed exactly, a fire causing death or serious injury may occur.

13

Image 15
Contents PLEASE CONTACT 1-800-913-8999 FOR ASSISTANCE STAINLESS STEEL GAS GRILL USE AND CARE GUIDEMODEL NO.720-0125-LP DO NOT RETURN TO PLACE OF PURCHASEIMPORTANCE SECTION THREE TABLETABLE OF CONTENTSSECTION TWO SECTION ONECALIFORNIA PROPOSITION 65-WARNING PRECAUTIONSSAFETY PRACTICES TO AVOID PERSONAL INJURY TESTED IN ACCORDANCE WITH ANSI Z21.58aNEVER USE A DENTED OR RUSTY PROPANE TANK PLACEMENT OF THE GRILLDO NOT INSTALL THIS UNIT INTO COMBUSTIBLE ENCLOSURES DO NOT USE BRIQUETTES OF ANY KIND IN THE GRILLASSEMBLY INSTRUCTIONS PLEASE READ THE INSTRUCTIONS CAREFULLY AND FOLLOW STEP BY STEPStep1: TheGlasso TheG T lassoM Step5 Remove the head unit of screws with four 81/4’*13mm screwsStep 6 Assemble the fortified steel to the main with 81/4’*13 ASSEMBLY INSTRUCTIONS Side burner valve assemblyScrews DO NOT TIGHTEN TheG T lassoM Step 8 Assemble the door to the grill as the figure show below‰ Opening the front door and place gas tank into the gas tank holes How to install a gas tankYour gas grill is ready to use L.P. GAS HOOK-UP LEAK TESTINGGAS HOOK-UP L.P. Tank RequirementsGas flow check INSTALLER FINALBEFORE TESTING TO TESTPROPANE TANK ASSEMBLE To begin OPERATING INSTRUCTIONUSING THE GRILL General use of the grillTO LIGHT THE GRILL BURNER LIGHTING INSTRUCTIONSFlame Characteristics WARNING IMPORTANT BEFORE LIGHTING…GRILL BURNER CLEANING USING THE SIDE BURNERCARE & MAINTENANCE WARNING IMPORTANT USING THE SIDE BURNERLIGHTING ILLUSTRATIONS Step1. Make sure the lid is openStep 2. Push and turn one of main or side burner knobs to HI position Approximate 1 1/2 “ Flame Height TO MATCH LIGHT THE GRILL WHEN TO LOOK FOR SPIDERS CARE & MAINTENANCE OF SIDE BURNERTROUBLESHOOTING BURNER CLEANINGEXPLODED VIEW PARTS LIST DO NOT LEAVE THE GRILL UNATTENDED WHILE COOKING ORDERING PARTSGRILL HINTS HOW TO ORDER REPLACEMENT PARTSGRILL COOKING CHART GRILL COOKING CHART GRILL COOKING CHART PORK CHOPS BBQ SALMONBAKED CHILI CORN TANGY SEAFOOD KABOBSEGGPLANT CAVIAR VEGETABLE KABOBSFAJITAS BEEF AND LAMB KABOBSTURKEY CHICKEN TANDOORI STYLESPARE RIBS PORK ROASTComponent LIMITED WARRANTY MODEL NO. 720-0125-LPWarranty Period STAINLESS STEEL OUTDOOR GAS GRILL