Mr. Coffee ECM10 U T I O N Pr E Ss U R E, SP E C I a L CO R D SE T in ST R U C T I O N S

Page 3

SP E C I A L CO R D SE T IN ST R U C T I O N S

1.A short power supply cord is provided to reduce the hazards resulting from becoming entangled in or tripping over a longer cord.

2.An extension cord may be purchased and used if care is exercised in its use.

3.If an extension cord is used, the marked electrical rating of the extension cord must be at least 10 amps and 120 volts. The resulting extended cord must be arranged so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped over accidentally.

This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to modify the plug in any way.

C A U T I O N : PR E SS U R E

In order to avoid possible burns to body parts and/or other injury from hot steam and water, NEVER open the cap while your MR. COFFEE® Steam Espresso/Cappuccino Maker is turned on or as long as there is pressure in the water reservoir.

In order to check if the appliance is under pressure, proceed as follows:

1.Turn the control knob to the “OFF” position and unplug the appliance.

2.Rotate the control knob to the “STEAM” position. If steam comes out of the frothing tube, then the water reservoir is still under pressure. Turn the control knob to the “OFF” position.

3.To release the pressure, hold a pitcher with water under the frothing tube

and immerse the frothing aid in the water. SLOWLY TURN THE CONTROL KNOB

TO THE “STEAM” POSITION AND RELEASE THE STEAM.

4.When the frothing tube stops releasing steam, slowly remove the cap.

5.Turn the control knob back to the “OFF” position.

6.Do not remove the filter holder at any time during the brewing process or until pressure is relieved.

7.Use caution when removing the filter holder from the brew head. The metal parts may still be very hot. Also, there may be hot water floating on the top of the filter basket.

8.If the filter holder is blocked, allow the appliance to cool down, then release the steam with the instructions above. The blockage may be caused by too finely ground coffee. See “PROBLEMS AND CAUSESon Page 11.

9.WHEN CLEANING THE FROTHING NOZZLE: Place a frothing pitcher or large cup (with at least an 11 ounce capacity) half full of water under the frothing aid.

Make sure the tip of the frothing tube is submerged in liquid before turning the control knob to the “steam” position.

3

Image 3
Contents Appuccino Maker IM P O R TA N T SA F E G U a R DS Read ALL Instructions Before Using the MachineSP E C I a L CO R D SE T in ST R U C T I O N S U T I O N PR E SS U R ETA B L E O F CO N T E N T S T R O D U C T I O NDI a G R a M O F Parts CoffeeGrind HOW to Brew Espresso Before Brewing Your First Carafe of EspressoPreparing the Coffee Make sure the control knob is in the OFF position For cleaning instructions, refer toBrewing Espresso Make sure the drip grid is in place on the drip trayHO W to MA K E C a P P U C C I N O Deliming Unplug the power cord from the electrical outletCarafe Cleaning To Delime Water ReservoirTo Delime Internal Parts Coffee comes Filter holder not rotated Tighten capAppliance was not turned on Or plugged Coffee has been tamped Turn on CompressedCafé Latte Café MochaCafé Americano Café MacchiatoConsumer Service Department Sunbeam PRODUCTS, INC Year Limited Warrant Y HOW to Obtain Warranty ServiceOtes Sunbeam Products. Inc. All rights reserved

ECM10 specifications

The Mr. Coffee ECM10 is a standout espresso machine designed for both novice coffee enthusiasts and experienced baristas. With its sleek design and user-friendly interface, it provides an excellent introduction to the world of espresso brewing at home.

One of the main features of the ECM10 is its 15-bar pump system. This powerful pump ensures optimal pressure during brewing, allowing for the extraction of rich flavors and aromas from coffee grounds. The result is a perfect espresso shot with a rich crema on top, a hallmark of a quality brew. Whether you prefer single or double shots, the ECM10 can accommodate both, giving you flexibility depending on your preference.

The machine is equipped with a stainless steel boiler that heats water quickly and maintains a consistent temperature throughout the brewing process. This technology is crucial for making espresso, as the water temperature needs to be perfectly balanced to extract the best flavor from the coffee. The ECM10 heats up rapidly, enabling you to enjoy your coffee without long waiting times.

Another notable characteristic of the ECM10 is its ease of use. The control panel features intuitive buttons that allow you to select various functions, including brewing, frothing, and temperature control. For those who enjoy a milk-based coffee, the ECM10 comes with a steam wand that can froth milk to create lattes and cappuccinos with ease. The steam pressure is adjustable, letting you achieve the desired richness and texture in your milk.

The machine also includes a removable water reservoir, making refilling and cleaning a breeze. The reservoir has a sizable capacity, allowing users to brew multiple cups of coffee throughout the day without frequent refills. The drip tray is designed to catch any spills, ensuring that your countertop remains tidy.

In terms of build quality, the ECM10 is constructed with durable materials, ensuring longevity and robust performance. Its compact design fits well in kitchens of various sizes, making it accessible to a wide range of users.

In summary, the Mr. Coffee ECM10 is an impressive espresso machine featuring a 15-bar pump system, stainless steel boiler for temperature control, user-friendly interface, and a steam wand for milk frothing. With its combination of ease of use, efficient design, and consistent performance, it is an excellent choice for anyone looking to elevate their home coffee experience.