Mr. Coffee ECM10 instruction manual Unplug the power cord from the electrical outlet, Deliming

Page 9

8.Follow the instructions on Page 3 under section marked “CAUTION: PRESSURE” to flush out any residual milk from the frothing tube and frothing aid.

9.Unplug the power cord and allow the machine too cool. Do not remove the reservoir cap or filter holder until the pressure in the machine has been released.

Follow procedures in section marked “CAUTION: PRESSURE” on Page 3 to relieve the pressure.

10.Continue to follow steps 7 – 8 in “Brewing Espresso” on Page 7.

CLE A N I N G YO U R E S P R E SS O/C A P P U CC I N O MA K E R

1.Unplug the power cord from the electrical outlet.

2.Remove frothing aid and wipe frothing tube and aid with a damp cloth. The frothing tube may still be hot, do not touch it with your hands. If steam does not flow through the frothing tube, the tube may be blocked with milk. Turn off and unplug the appliance. After the appliance has cooled, clean the frothing tube with a needle.

3.The carafe, carafe lid, filter holder, filter basket, and drip tray can be washed with soapy water or placed on the top rack only of your dishwasher. CAUTION: Do not immerse appliance

in water. Do not remove reservoir cap while appliance is under pressure. See Section

“CAUTION: PRESSURE” on Page 3.

4.After the pressure has been released, remove reservoir cap. Discard the remaining water through the top opening of the water reservoir by turning the appliance upside down over the sink. Always empty the water reservoir of any water between uses.

Do not immerse appliance in water. Screw the reservoir cap back in place.

5.Wipe housing with a soft wet cloth. Do not use abrasive cleaners or scouring pads as they will scratch the finish.

6.Do not store the filter holder in the brew head. This can adversely affect the seal between the brew head and the filter holder while brewing espresso.

DELIMING

Mineral deposits built-up in the Espresso Maker will affect the operation of the appliance. Your Espresso Maker must be delimed when you begin to notice an increase in the time to brew espresso, or when there is excessive steaming. Also, you may notice a build up of white deposits on the surface of the brew head.

The frequency of cleaning depends upon the hardness of the water used. The following table gives the suggested cleaning intervals.

SUGGESTED CLEANING INTERVAL

Type of Water

Cleaning Frequency

Soft Water

Every 80 Brew Cycles

Hard Water

Every 40 Brew Cycles

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Appuccino Maker IM P O R TA N T SA F E G U a R DS Read ALL Instructions Before Using the MachineSP E C I a L CO R D SE T in ST R U C T I O N S U T I O N PR E SS U R ETA B L E O F CO N T E N T S T R O D U C T I O NDI a G R a M O F Parts CoffeeGrind HOW to Brew Espresso Before Brewing Your First Carafe of EspressoPreparing the Coffee Brewing Espresso For cleaning instructions, refer toMake sure the drip grid is in place on the drip tray Make sure the control knob is in the OFF positionHO W to MA K E C a P P U C C I N O Deliming Unplug the power cord from the electrical outletCarafe Cleaning To Delime Water ReservoirTo Delime Internal Parts Appliance was not turned on Or plugged Tighten capCoffee has been tamped Turn on Compressed Coffee comes Filter holder not rotatedCafé Americano Café MochaCafé Macchiato Café LatteConsumer Service Department Sunbeam PRODUCTS, INC Year Limited Warrant Y HOW to Obtain Warranty ServiceOtes Sunbeam Products. Inc. All rights reserved

ECM10 specifications

The Mr. Coffee ECM10 is a standout espresso machine designed for both novice coffee enthusiasts and experienced baristas. With its sleek design and user-friendly interface, it provides an excellent introduction to the world of espresso brewing at home.

One of the main features of the ECM10 is its 15-bar pump system. This powerful pump ensures optimal pressure during brewing, allowing for the extraction of rich flavors and aromas from coffee grounds. The result is a perfect espresso shot with a rich crema on top, a hallmark of a quality brew. Whether you prefer single or double shots, the ECM10 can accommodate both, giving you flexibility depending on your preference.

The machine is equipped with a stainless steel boiler that heats water quickly and maintains a consistent temperature throughout the brewing process. This technology is crucial for making espresso, as the water temperature needs to be perfectly balanced to extract the best flavor from the coffee. The ECM10 heats up rapidly, enabling you to enjoy your coffee without long waiting times.

Another notable characteristic of the ECM10 is its ease of use. The control panel features intuitive buttons that allow you to select various functions, including brewing, frothing, and temperature control. For those who enjoy a milk-based coffee, the ECM10 comes with a steam wand that can froth milk to create lattes and cappuccinos with ease. The steam pressure is adjustable, letting you achieve the desired richness and texture in your milk.

The machine also includes a removable water reservoir, making refilling and cleaning a breeze. The reservoir has a sizable capacity, allowing users to brew multiple cups of coffee throughout the day without frequent refills. The drip tray is designed to catch any spills, ensuring that your countertop remains tidy.

In terms of build quality, the ECM10 is constructed with durable materials, ensuring longevity and robust performance. Its compact design fits well in kitchens of various sizes, making it accessible to a wide range of users.

In summary, the Mr. Coffee ECM10 is an impressive espresso machine featuring a 15-bar pump system, stainless steel boiler for temperature control, user-friendly interface, and a steam wand for milk frothing. With its combination of ease of use, efficient design, and consistent performance, it is an excellent choice for anyone looking to elevate their home coffee experience.
Top Page Image Contents