Section Electrical, Power Supply | Mermaid REFRIGERATION/FREEZER

together, they allow the refrigerant to flow through the system without leaking out to the atmosphere. If needed, they can be undone to enable a faulty component to be removed & replaced without leaking refrigerant.

Never run the compressor unless all components of the system are connected together.

B: Connecting the Quick Connect Fittings:

Leave the clear plastic dust plugs installed until you are ready to connect the system together. After you have removed the plugs, keep them in a safe place in case you need to remove or replace a component later. Push the male & female fittings together & then carefully rotate the collar on the female fitting until it starts on the thread on the male end, making sure that the fitting is not cross-threaded & the male end does not rotate. Continue making up the collar of the female end, either by hand or with a crescent wrench, while preventing the male end from rotating by restraining it with another wrench. It is most important not to let the male end rotate at all during this whole process. Tighten the collar until it nearly covers the threads on the male fitting. It is not necessary to use excessive force as the seal that stops the refrigerant from escaping is made with an o-ring & does not depend on the fitting being wrenched down hard. If there is a continuous hiss after the connection has been completed, disconnect the fitting & check that the o-ring has not been damaged.

SECTION 8 (ELECTRICAL)

A: Power Supply:

The power supply to the Electronic Control Module must given particular attention to prevent nuisance problems & compressor non-operation, shutdown, or failure. All incoming power electrical connections should be either soldered or made with good quality crimpers & crimp connectors of the correct size & type. All switches, breakers & connections must be in good condition & be designed & constructed for marine use. It is suggested that during the initial start-up the supply voltage be monitored at the terminals on the Module before, during, & after the compressor starts, to ensure that the voltage stays steady & does not fall appreciably. This test should be conducted with as many other DC loads turned on as is practical. Each model Mermaid produces is pre-wired and tested for voltage drop. It is not necessary to change any wiring connections made at the factory unless damaged during installation. This section is to ensure your incoming power (12VDC, and/or 110V) is wired properly to the pre-stripped connections from the Mermaid factory.

REFRIGERATION/FREEZER specifications

Mermaid Refrigeration/Freezer appliances stand out in the market due to their superior efficiency and reliable performance, making them a preferred choice for both residential and commercial applications. These advanced cooling systems are designed to preserve food, beverages, and other perishable items at optimal temperatures, ensuring freshness and safety.

One of the main features of Mermaid Refrigeration/Freezers is their energy efficiency. Equipped with state-of-the-art inverter technology, these units adapt their cooling output based on the load, resulting in lower energy consumption and reduced electricity bills. This feature not only benefits consumers financially but also aligns with global efforts to promote sustainability and environmental responsibility.

Another defining characteristic of Mermaid appliances is their spacious and flexible interior layouts. Many models offer adjustable shelving and configurable compartments that allow users to maximize their storage space. This versatility is particularly advantageous in commercial settings where different sizes and types of items need to be organized efficiently.

Mermaid Refrigeration/Freezers also come with advanced temperature management systems. These systems utilize digital controls and smart sensors to maintain precise temperature settings, which can be crucial for food safety and preservation. Additionally, some models incorporate rapid cooling and freezing technology, ensuring that newly added items are brought down to the desired temperature quickly, minimizing temperature fluctuations.

In terms of design, Mermaid units are often praised for their sleek and modern aesthetics. They feature stainless steel exteriors that not only look good but are also resistant to corrosion and easy to clean. Many models come with LED lighting, enhancing visibility while being energy-efficient.

The appliances are also designed with user convenience in mind. Features such as self-defrosting, adjustable thermostats, and door alarms add to the ease of use and ensure that the fridge/freezer operates seamlessly. Moreover, some models are equipped with smart technology, allowing homeowners to monitor and control their appliances remotely via smartphone apps.

Lastly, durability is a hallmark of Mermaid products. Constructed with high-quality materials and robust components, these refrigeration units are built to withstand the rigors of daily use. With proper care, they can provide reliable service for many years, making them a wise investment for any kitchen. In summary, Mermaid Refrigeration/Freezers offer a combination of energy efficiency, versatile storage options, advanced technology, and contemporary design, making them an excellent choice for consumers and businesses alike.