TOP Panel Features

a) If a track is not playing, the JOG WHEEL will search slowly through a track's frames. To set a new cue

point, rotate the JOG WHEEL then

begin playback when you have determined the proper position. Press CUE to return to that cue point.

b) If a track is playing, the JOG WHEEL will temporarily bend the pitch of the track. Rotating the JOG WHEEL clockwise temporarily speeds it up while rotating it counterclockwise slows it down. This is a useful tool for beat- matching.

c) When the SEARCH button has been activated, rotating the JOG WHEEL will scan rapidly through the track.

TRACK KNOB – Turn this knob to select a track to play. Press this knob to skip through your track listing 10 tracks at a time.

PROGRAM – This button helps you create a program – a sequence of tracks to play continuously. To create a program, press PROGRAM when the CD player is paused. To enter a track into the program, use the TRACK KNOB to select the desired track then press PROGRAM to enter it. Repeat this process for each track you want to enter (in the order you want them to play). When you have finished, press PLAY / PAUSE to start playing the program. The tracks will play in the order you entered them, and "PROGRAM" will be shown on the LCD. To cancel your program as it is playing, press and hold PROGRAM for 2 seconds so "PROGRAM" disappears from the LCD.

1.EJECT – Pressing will open or close the disc tray on the transport. This unit is designed to play commercially available CDs and properly burned and finalized

CD-Rs. Due to variances on the specification of certain CD burners and CDs, some homemade CDs may not play properly. We recommend burning CDs at the minimum speed possible for the best performance.

2.PLAY / PAUSE – Plays or pauses the track. Pausing the track will create a cue point at that location (which can be adjusted with the JOG WHEEL in Search Mode).

3.CUE – During playback, pressing CUE will return to the most recent point where playback was started and will pause the track. Holding down CUE will start playback from this point, and releasing CUE will cause it to return to that point and will pause the track. Also, if the track is paused, you can use the JOG WHEEL to locate a new cue point.

4.SEARCH – Pressing this button allows you to use the JOG WHEEL to rapidly scan through the music. The LED indicator will be red when Search Mode is active. (Note: If the JOG WHEEL is not used for 8 seconds, Search Mode will be deactivated.)

5.JOG WHEEL – The jog wheel serves many functions depending on its current mode.

	16	8
1		8
1
		7
10	11	12
6		13
		13
		4

5 14

2 15

8.SINGLE – Press this button to toggle between Single Play (the deck will stop at the end of each track) or Continuous Play (the entire disc will be played without interruption).

9.TIME – Switches the time display between elapsed playing time, remaining time on the track, and total remaining time on the entire CD.

10.LOOP IN – Sets a new cue point or the start point of a loop (a "Loop In" point) during playback.

11.LOOP OUT – Sets the end point of a loop (a "Loop Out" point) and starts playing the loop. While playing a loop, press LOOP OUT to release it from the loop and continue normal playback.

12.RELOOP – Plays the track immediately from the beginning of a loop (and reactivates the loop).

13.PITCH – Adjusts the range of the PITCH FADER (±4%, 8%, and 16%). The current range will be indicated on the LCD and by different LEDs.

14.PITCH FADER – The pitch can be changed by pressing the PITCH button so a PITCH LED is lit, then moving the sliding fader. The pitch will not be changed if the PITCH LED is off.

15.PITCH BEND -/+ – You can use these two pitch bend buttons to temporarily adjust the pitch and tempo of the music up to -/+ 16% from the current pitch setting.

16.LCD – Indicates all the functions, as they are occurring, with the CD.