Server Technology Series 93I manual Unit TAKE-DOWN, Safety Guidelines, Démontage DE L’APPAREIL

Page 3

E N G L I S H

UNIT TAKE-DOWN

REMOVE LID OR PUMP.

REMOVE STAINLESS STEEL JAR OR HOLDCOLD JAR FROM SHROUD OR BASE.

IF USED, REMOVE EUTECTIC ICE PACK FROM SHROUD OR BASE.

RE-FREEZE EUTECTIC ICE PACK(S) OR HOLDCOLD JAR(S).

Each eutectic ice pack must be allowed to freeze for about 12 hours (or overnight) prior to use.

Each HOLDCOLD jar must be allowed to freeze upside down for about 8 hours (or overnight) prior to use.

SAFETY GUIDELINES

According to food and safety regulations, most foods must be stored and/or served at certain temperatures or they could become hazardous. Check with your local food and safety regulators for specific guidelines.

Be aware of the product you are serving and the temperature the product is required to maintain. Server Products Inc. can not be responsible for the serving of potentially hazardous product.

NSF International lists this pump as: “NOT ACCEPTABLE FOR DISPENSING POTENTIALLY HAZARDOUS FOODS.”

Stainless steel is one of the best materials for food serving and storage, but there are many products which can corrode it. If you notice corrosion beginning on any stainless steel surface, you may need to change the cleansing agent, sanitizing agent, or the cleaning procedures you are using.

Products containing: acids, alkalines, chlorine, or salt can corrode stainless steel.

Sauerkraut corrodes stainless steel. Server Products Inc. regrets that we can not honor warranty claims on stainless steel parts that have been affected by sauerkraut.

Insulated Units

DO NOT EXPOSE THE INSULATED SHROUD OR BASE OF THE UNIT TO A DISHWASHER OR TEMPERATURES OVER 150°F, THIS WILL DAMAGE THE INSULATION.

DO NOT PLACE ICE PACKS OR CRUSHED ICE INTO NON-INSULATED UNITS, they are not designed to hold water and will leak.

Eutectic Ice Packs and HOLDCOLD Jars

Do not expose ice packs OR HOLDCOLD JARS to a dishwasher or any extreme heat, this could cause leakage or explosion of the ice packs or HOLDCOLD jars.

F R A N Ç A I S

DÉMONTAGE DE LAPPAREIL

RETIREZ LE COUVERCLE OU LA POMPE.

RETIREZ LE RÉCIPIENT EN ACIER INOXYDABLE OU LE RÉCIPIENT HOLDCOLD DE LA COQUE OU DU SOCLE.

LE CAS ÉCHÉANT, RETIREZ LE CRYOSAC DE LA COQUE OU DU SOCLE.

RECONGELEZ UN OU PLUSIEURS CRYOSACS OU RÉCIPIENTS HOLDCOLD.

Chaque cryosac doit rester au congélateur pendant 12 heures environ (ou toute une nuit) avant usage.

Chaque récipient HOLDCOLD doit rester au congélateur pendant 8 heures environ (ou toute une nuit) avant usage, placé à l’envers.

CONSIGNES DE SÉCURITÉ

Conformément aux réglementations alimentaires et de sécurité, la plupart des aliments doivent être stockés et/ou servis à certaines températures sous peine de devenir dangereux. Renseignez-vous auprès des instances réglementaires locales pour obtenir des consignes spécifiques.

Ne perdez pas de vue la nature du produit servi et la température à laquelle vous devez le maintenir. Server Products, Inc. ne peut pas être responsable du service de produits potentiellement dangereux.

La NSF International définit cette pompe ainsi : « Ne convient pas à la distribution d’aliments potentiellement dangereux ».

L’acier inoxydable est l’un des meilleurs matériaux pour le service et la conservation des aliments, cependant une grande quantité de produits peut le corroder. Si vous remarquez la moindre trace de corrosion sur l’acier inoxydable, il serait sage de changer votre produit de nettoyage ou de désinfection, ou encore de modifier les procédure de nettoyage que vous utilisez.

Les produits contenant : des acides, des produits alcalins, du chlore ou du sel risquent de corroder l’acier inoxydable.

La choucroute corrode l’acier inoxydable. Server Products, Inc. regrette de ne pas pouvoir honorer les demandes sous garantie portant sur les pièces en acier inoxydable détériorées par de la choucroute.

Modèles isothermes-

Ne passez pas la coque ou le socle isotherme du distributeur au lave-vaisselle et ne l’exposez pas à des températures supérieures à 66 °C, sous peine d’endommager la matière isolante.

E S P A Ñ O L

DESARMADO DE LA UNIDAD

RETIRE LA TAPA O LA BOMBA.

RETIRE DEL RESGUARDO O LA BASE EL RECIPIENTE DE ACERO INOXIDABLE O EL RECIPIENTE HOLDCOLD.

RETIRE TAMBIÉN EL PAQUETE EUTÉCTICO DEL RESGUARDO O LA BASE, SI CORRESPONDE.

VUELVA A CONGELAR LOS PAQUETES EUTÉCTICOS DE HIELO O LOS RECIPIENTES HOLDCOLD.

Antes de usar cada paquete eutéctico de hielo, deje que se congele por aproximadamente 12 horas (o durante la noche).

Antes de usar cada recipiente HOLDCOLD, deje que se congelen en posición invertida por aproximadamente 8 horas (o durante la noche).

PAUTAS DE SEGURIDAD

Según las normas sobre alimentos y seguridad, la mayoría de los alimentos deben almacenarse o servirse a cierta temperatura, de lo contrario pueden ser peligrosos. Consulte las normas locales sobre pautas específicas de seguridad y alimentos.

Tenga presente el producto que se va a servir y la temperatura de conservación que éste requiere. Server Products, Inc. no puede hacerse responsable por servir un producto potencialmente peligroso.

NSF International registra esta bomba como: “No apta para dispensar alimentos potencialmente peligrosos”.

El acero inoxidable es uno de los mejores materiales para servir y almacenar alimentos, pero existen muchos productos que pueden corroerlo. Si detecta signos de corrosión en alguna superficie de acero inoxidable, puede que sea necesario cambiar los agentes de limpieza o desinfección, o bien modificar los procedimientos de limpieza.

Los productos que contienen: agentes ácidos o alcalinos, cloro o sal pueden corroer el acero inoxidable.

El chucrut corroe el acero inoxidable. Server Products, Inc. no ofrece ninguna garantía para las piezas de acero inoxidable que resulten afectadas por el chucrut.

Unidades aisladas

No lave el resguardo o la base de la unidad en lavadoras de vajilla ni los exponga a temperaturas superiores a 65,5°C, ya que se dañará el aislamiento.

01804 3

Image 3
Contents 01804-00L-092205 Armado DE LA Unidad Installation DE L’APPAREILDown, Safety Guidelines, and Cleaning Unit SET-UPConsignes DE Sécurité Safety GuidelinesUnit TAKE-DOWN Démontage DE L’APPAREILNettoyage Safety Guidelines ContinCleaning Consignes DE Sécurité ContinServer Products Limited Warranty Service Réparations ServicioOrdering Replacement Parts General SERVICE, REPAIR, or Returns94000 CSM 94114 94115 Dicsm 94070 MMS

Series 93I specifications

The Server Technology Series 93I is an advanced power distribution unit (PDU) specifically designed to meet the demands of high-density data centers. This innovative unit brings together a range of features and technologies that ensure efficient power management, reliability, and easy integration into existing infrastructures.

One of the standout features of the Series 93I is its capability to support high-density applications. With a power rating of up to 40 Amps, it accommodates various configurations, making it ideal for modern data centers that require substantial power for multiple devices. The PDU's robust design allows it to handle the increasing power loads associated with contemporary IT equipment without compromising performance or safety.

The Series 93I incorporates intelligent power monitoring technology. With real-time monitoring capabilities, users can track power consumption at both the PDU and outlet levels. This feature not only helps in optimizing power usage but also plays a crucial role in identifying potential overloads and ensuring the overall health of the electrical system within the data center. The integration of local and remote monitoring options provides users with flexibility and control over their power infrastructure.

Another key characteristic of the Series 93I is its construction. Housed in a rugged aluminum chassis, the PDU is designed for durability while providing efficient heat dissipation. Its modular design allows for easy installation and adaptability to different environments, ensuring seamless integration into various racks and enclosures.

User-friendliness is another priority for the Series 93I. It comes equipped with an intuitive LCD display that presents vital information, including load levels, voltage, and current, aiding in quick diagnostics and ease of use. Additionally, the unit features numerous mounting options, allowing for vertical or horizontal installation based on the specific requirements of the data center layout.

Safety features are also prominent in the design of the Series 93I. It integrates advanced surge protection and isolation to safeguard sensitive equipment, ensuring smooth operations in the event of electrical anomalies. Moreover, compliance with industry standards guarantees that the unit meets the highest safety and performance benchmarks.

In conclusion, the Server Technology Series 93I stands out in the crowded space of power distribution solutions, blending high capacity, intelligent monitoring, and safety features in a robust design. As data centers continue to evolve, the Series 93I remains a critical asset for managing the complex power demands of modern IT infrastructures. Its combination of technology, durability, and user-centric features makes it a preferred choice for operators seeking reliable and efficient power management solutions.