Turbo Chef Technologies 3240 manual Sche MAT ICS

Page 71

47

SCHE MAT ICS

Page 70 Page 72
Image 71
Page 70 Page 72
Contents Accelerating the World of Cooking TM Page 800.90TURBO For further information, callPage Table of Contents Oven Systems Oven ModesAppendix a Replacing Oven Components TroubleshootingSchematics Schematic Pin-out Controller CodesA F ET Y Instruc Tions Important Safety Information Please Read FirstGeneral Safety Information Preventing Oven DamageGrounding Instructions Power Cord ReplacementReducing Fire Risk I S a F ET Y Instruc Tions Specifications and Startup Page Oven Overview, Front OverviewOven Construction DimensionsPower Specifications CertificationsReading the Gas Pressure at 100% Flame Gas SetupReading the Incoming Gas Pressure Static Confirming Proper Closure of all Taps Reading the Gas Pressure at Minimum FlameReading the Operating Gas Pressure Cleaning Page Message has disappeared Daily Cleaning ProceduresYour HhC oven Pad, cleaning towels, disposable gloves Follow the steps below daily to help maintainL E a N I N G Deep Cleaning ProceduresRemove and Clean the Right and Left Lower Air Diverters Remove and Clean the Conveyor requires TWO peopleRemove and Clean the Lower End Panels Remove and Clean the Upper Nozzle PlateReinstall the Oven Components Clean the Oven InteriorStandard Oven Operation Page Oven Controls Happens When Mode 1 Oven OffMode 2 Belt Speed Select Cooking a ProductMode 6 Cooking Mode 3 LightingMode 4 Warming Mode 5 SoakingUser presses the idle key from Mode Mode 8 IdleMode during which both blowers are reduced To 30% to save power. All other ovenAdjust the air speed This page intentionally Left blank Oven Modes Page Updating the Firmware Config ModeTo access the Config MODE, press the up key Smart Card ScreenEdit Option Screen Setup ModeAccessing the Setup Mode Accessing the Test ModeInfo Screen Test ModeEnable/disable maintenance mode* -Clear the fault counts Changing the Display LanguageBlowers Bottom Display Line Entering a New Serial NumberConfirmed Erasing all Oven SettingsInitiating a Burn-In Test Viewing the Serial NumberOven Systems Page Control System Keypad is an 11-key membrane switch+V for 24 VDC with output wires Or C & no are closed when coilPower supply is damaged or defective Power Supply 24VDC InternationalDisconnect line voltage from the unit Conveyor SystemSmart Card Reader Thermostat 120ºF Close on RiseTerminals Wire harness for damage or shortsIf the resistance readings are correct Voltage applied to the motor windingsBlower System Blower Motor Ohm Chart Motor WindingsBurner System VAC installation connect wire a red to wire C blueCheck for 24 VAC leaving the ignition module see , VDC at the modulating valve coilWill isolate the burner spark rod from Using a different wire spark cable ensureApply power to the ignition module Shut off the gas supplyTroubleshooting Page Cooking profile Overview of TroubleshootingFault Code Descriptions RO U B L E S H O OT I N G This fault occurs if the conveyor belt fails to startFault Code Troubleshooting Properly connected to Reset maximum and low fire gas pressureSteps 9-13? Open the right end bellThis page intentionally Left blank Replace Wire spark Cavity temperature?Temperature Burner ignite Fault Clear?Former have 24 VAC A-14 Check YES Wiring ReplaceAdjust the 100% Air tube SwitchChassis? Troubleshooting F5 CC Over Temp CC Over TempIs the white wire Shorted toOpen the left end bell. Are the cooling fans running? Troubleshooting F6 EC Over Temp EC Over TempCheck Wiring YES YES Is the oven hot? noControl board A-8 Troubleshooting F7 RTD Fault RTD FailureTroubleshooting F8 High Limit Tripped High Limit Trip Is the wiring correct page 45?Remove the chain guard page A-6 Troubleshooting F9 Belt Fault Total Belt Run FailureCheck Wiring Switch closed?Is line voltage Blower running? Is the wiring A-8 Air switch Air tubeNon-Fault Code Troubleshooting 29-30? Cleaned? Problem starting?Correctly reinstall Codes present? Does the problem OperationA-8 Correct wiring Control board to Correct wiring Display If ribbon cable isPower? Check wiring from Verify 5 VDC is presentThis page intentionally Left blank Schematics Page CH E Mati CS C H E Mati C S Sche MAT ICS Page Appendix a Replacing Oven Components Page To Replace This Replacing Oven Components103572 No Panel Appendix a Replacing Oven Components This page intentionally Left blank Replacing Items No Panel Removal Required Part Number Hardware Description Hardware Part Numbers Replacing Items Right End Bell Blower Motor, Lower HHC-6520 Key, 3/16 0 Appendix a Replacing Oven Components Gear Drive Assembly DetailX1 each Replacing Items Left End Bell Blower Motor, Upper HHC-6520 Key, 3/16 Replacing Items Burner Compartment Cover Burner Assembly DetailReplacing Items Multiple Panel Removal Required Page Page For service or information

3240 specifications

Turbo Chef Technologies 3240 is a cutting-edge cooking appliance that embodies innovation and efficiency for commercial kitchens. Designed to meet the demands of the modern food service industry, this versatile solution combines advanced cooking technologies to deliver outstanding performance while ensuring culinary excellence.

At the heart of the Turbo Chef 3240 is the patented High Speed Hybrid Technology. This system integrates rapid cook air impingement with microwave cooking, allowing for faster cooking times without compromising quality. The result is perfectly cooked food that retains its moisture and flavor, making it an ideal choice for restaurants, cafes, and other food service establishments that require quick turnaround without sacrificing taste.

One of the standout features of the Turbo Chef 3240 is its sleek, compact design. The unit is built to maximize kitchen space while providing a generous cooking capacity. With a user-friendly interface and touchscreen controls, operators can effortlessly navigate through various cooking modes, adjust settings, and monitor cooking progress. This ease of use is particularly beneficial in high-pressure environments where efficiency is paramount.

Another key characteristic of the Turbo Chef 3240 is its exceptional versatility. It can handle a wide range of menu items, from pizzas and baked goods to proteins and vegetables. With multiple cooking modes, including rethermalization, toasting, and baking, the Turbo Chef 3240 is equipped to handle any culinary challenge. Additionally, the ability to program custom recipes allows chefs to maintain consistency and quality across their offerings.

Energy efficiency is also a significant consideration in the design of the Turbo Chef 3240. The appliance is engineered to use less energy than traditional cooking methods, making it a responsible choice for businesses looking to reduce their environmental footprint. This commitment to sustainability does not come at the expense of performance; instead, it enhances the overall efficiency of the kitchen.

Durability is another hallmark of the Turbo Chef 3240. Constructed with high-grade materials, this unit is designed to withstand the rigors of daily use in a commercial environment. Maintenance is simplified, with accessible components that facilitate cleaning and upkeep, ensuring that the unit remains in optimal condition.

In conclusion, the Turbo Chef Technologies 3240 stands out as an innovative solution for commercial kitchens, combining speed, versatility, and energy efficiency in one powerful appliance. Whether for small cafes or large restaurants, the Turbo Chef 3240 provides a reliable way to enhance culinary offerings while streamlining kitchen operations.
Top Page Image Contents