Wayne-Dalton 600 manual Distributed By, Part I General, Part I I Products, Part III Execution

ROLLING GRILLES

6 0 0 S E R I E S
Note to specifiers: Words in brackets indicate frequently specified and highly recommended options.
PART I – GENERAL			1.07	Delivery, Handling, Storage	2.07	Operation
1.01		Work Included
	A.	The opening will be equipped withWayne-Dalton	A.	Deliver products in manufacturer’s original containers,	A.	Grilles will be operated by means of (manual,with lift
		600 Series rolling grilles.	B.	dry,undamaged,seals and labels intact.		handles) (by chain and gear–maximum pull of 35 lbs.)
1.02		Related Work		Store and protect products in accordance with		(by fully enclosed awning type crank gearing and
				manufacturer’s recommendations.		removable crank arm) (by motor operator).
	A.	Opening preparation, miscellaneous or structural metal	1.08	Warranty	2.08	Locking
		work, access panels, finish or field painting, field
		electrical wiring, wire, conduit, fuses, and disconnect	A.	Standard manufacturer’s one year warranty against	A.	Manual or crank operated grilles to be by means of
		switches are in the Scope ofWork of other divisions		defects in material and workmanship.		slide bolt locking device operable from inside or
		or trades.	PART I I – PRODUCTS			outside. Chain lock keeper on chain operated doors.
1.03		Reference Standards				Motor operated grilles to include self-locking gearing
			2.01	Curtain		plus chain locking device for emergency chain.
	A.	ANSI/DASMA203 – American National Standards	A.	Curtains are to be fabricated of 5/16" galvanized	Note: When specifying locks on electric-motor operated
		Institute Specifications for non-rated fire rolling doors		steel horizontal rods,continuous from jamb to jamb,		doors,electric interlocks should also be specified to
		published by Door &Access Systems Manufacturers		covered with aluminum tubes.Vertical links and tubes		prevent operation when lock bolts are engaged in the
	B.	Association International.		available in stainless,aluminum or galvanized steel. End		guides,thus preventing damage to the curtain
ings		ASTM A123 – Zinc [hot-dipped galvanized] coat-		links insure that grille cannot be pulled from guides.		and/or operator.
	C.	on iron and steel products.	2.02	Guides	PART III – EXECUTION
		ASTM A229 – Steel wire,oil-tempered for	A.	Guides will be of extruded aluminum with wool pile	3.01	Installation
	D.	mechanical springs.		inserts to contact both faces of grille,acting as wearing	A.	General:
		ASTM A-653-94– Steel sheet,zinc-coated		surfaces and sound deadener.		1. Install grilles in accordance with manufacturer’s
		[galvanized] by the hot-dipped process,	2.03	Brackets		instructions and standards. Installation shall be by an
		commercial quality.				authorizedWayne-Dalton representative.
1.04		Quality Assurance	A.	Bracket Plates will be of 3/16” minimum [1/4”] steel		2. Verify that existing conditions are ready to receive
				plate. Sealed ball bearings to support the		rolling grille work.
	A.	Rolling grilles and all accessories and components		counterbalance assembly. Brackets to form end		3. Beginning of rolling grille work means acceptance
		required for complete and secure installations shall be		closures and support hoods.	B.	of existing conditions.
		manufactured as a system from one manufacturer.	2.04	Counterbalance		Install grille complete with necessary hardware,jamb
1.05		Systems Description				and head mold strips,anchors,inserts,hangers,and
			A.	Curtain to be coiled on a pipe of sufficient size to		equipment supports in accordance with final shop
	A.	Rolling Grille:Type:		carry door load with deflection not to exceed .033"		drawings,manufacturer’s instructions,and as specified
	B.	Model 600		per foot of door span and to be correctly balanced by	C.	herein.
		Mounting:[steel] [wood] [masonry] jambs		helical springs,oil tempered torsion type. Cast iron		Fit,align and adjust rolling grille assemblies level and
	C.	Operation:[manual push-up] [crank] [chain hoist]		barrel plugs will be used to anchor springs to tension	D.	plumb for smooth operation.
	D.	[motor] [motor with chain hoist]		shaft and pipe.		Upon completion of final installation,lubricate,test and
		Material:[Galvanized steel] [aluminum] [stainless steel]	2.05	Hood		adjust grilles to operate easily,free from warp,twist or
1.06		Submittals			Note:	distortion and fitting for entire perimeter.
			A.	When required,hood is to be fabricated of 24-gauge		Architect may consider providing a schedule when
	A.	Shop Drawings:Clearly indicate the following:		galvanized steel (stainless steel) (20 B&S gauge		more than one rolling grille or opening type is
		1. All details required for complete operation		aluminum). Provide intermediate hood supports over		required.
		and installation.		16'0" opening width.
		2. Hardware locations.	2.06	Finish
		3. Type of metal and finish for door sections.
		4. Finish for miscellaneous components and		Finish for aluminum surfaces is to be (mill) (clear
	B.	accessories.		anodized 204R1)(bronze anodized). Non-galvanized
		Product Data:Indicating manufacturer’s product		steel surfaces are to be painted one shop coat of rust
		data,and installation instructions.		inhibiting primer. Stainless steel to be #304 brushed.
Because of continuing product improvements, we reserve the right to change the product specifications and designs without prior notice.

Distributed By:

wwwFor technic.waynel i formation,-daltonvisit:.com/commercial

© 2008 Wayne-Dalton Corp. • One Door Drive • Mt. Hope, Ohio 44660 • 800-255-3046

Mt. Hope, OH • Dalton, OH • Trail, OH • Pensacola, FL • Portland, OR

Printed in U.S.A.

Item #333072 Revised 4/2008