Kenmore 790.4282 Operating the Bridge Surface Element, To Operate the Bridge Surface Element

Page 12

Setting Surface Controls (cont'd)

Operating the Bridge Surface Element

The cooktop is equipped with a"BRI DGE" surface eJement locatedat the leftcooktop position (See Figures I & 2). Indicatorlights on the cooktop are used to indicatewhat portions of the Bridge eJementwill heat. The Bridge element

begins with the leftFRONT position only (Figures 3 & 4) andFigure 1 when selected with the +BRIDGE element (Figures 5 & 6) it

will provide a combination of 2 heating surfaces. When set for ALL 3 element positions the leftrear element isadded for a total combination of 3 even heating surfaces (See Figures 7 & 8).

The Bridge element is designed for rectangular or oval shaped cookware. The griddle that is supplied with this appliance should be used with the Bridge element ONLY. For round shaped cookware, the left front and left rear elements may be used as a single element.

To Operate the Bridge Surface Element:

1.Place correctly sized cookware on the radiant surface element.

2.Touch and hold the P_'-w_key pad until a beep sounds. The power indicator light will turn

ON. Note: If no key pad is touched within 20 seconds the request to Power ON the cooktop will clear.

3. Touch and hold the _i}

pad for the Bridge element position until a beep is heard. The

display will show" --

". Note: If no further pads are touched within 10 seconds the request

to power the element

ON will clear.

4.Select the FRONT (See Figures 3 & 4), +BRIDGE (See Figures 5 & 6) or ALL 3 elements

(See Figures 7 & 8) to heat by pressing the _!} pad once, twice or three times. When

the bridge is set to ALL setting, the display of the left rear element changes to reflect the same setting as the left front element.

Figure 2

i (_) A,

W

_ @+Bridge

w Q_j Front

Figure 4

Figure 3

i (_ All

W

@+Bridge

w @ Front

Figure 6

Figure 5

,, C All

I @+Bridge

w (_}_ Front

5.

Touch HI @

pad once to turn ON the power levelto HI. Touch Lo @

pad once for Lo.

 

 

6.

Each touch of the HI

or Lo

pad will decrease or increase

the power level

Figure 7

Figure 8

 

from 9.5 through 3.0 by .5 increments. Simmer power levels between 3.0 and 1.2 will decrease or increase by .2 increments.

 

Lo is the lowest

power level available. Note: The power level may be adjusted at any time while the element is ON.

7.Start most cooking operations on a higher setting and then turn to a lower setting to finish cooking. Each surface element provides a constant amount of heat at each setting. A glowing red surface heating area extending beyond the bottom edge of the cookware indicates the cookware is too small for the surface heating area.

J

8. When cooking has been completed touch the (on/of_pad once to turn the element OFF and if no other surface element is

used touch the P_-wE'key pad to turn off he cooktop. Note: The HE (hot element) message will remain ON if the cooktop is still hot and will remain ON until the heating surface area has cooled sufficiently.

Radiant surface elements may appear to have cooled after they have been turned off. The glass surface may still be hot and burns may occur if the glass surface is touched before it has cooled sufficiently.

Do not place aluminum foil or plastic items such as salt and pepper shakers, spoon holders or plastic wrappings on top of the range when it is in use. These items could melt or ignite. Potholders, towels or wooden spoons could catch fire if placed too close to the surface elements.

Warm & Hold Feature

The Warm & Hold feature may be used with any of the Cooking Elements.

To Turn the Warm & Hold Feature ON:

1.To select the Warm & Hold feature for any Cooking Element touch the _o_/o_f}key pad for the

corresponding

Cooking Element.

 

Fig. 9

2. Touch the _

key pad located in the main control

area. The associated

display will show LH (low heat - Fig. 9)

indicating that the Cooking Element is properly set

to Warm & Hold. If no other key pads are pressed the control will

activate the desired Cooking Element at the Warm

& Hold setting.

 

 

 

12

 

Image 12
Contents Parrilla Cocinar Lectrica Contents Read all instructions before using this appliance Save these instructions for future referenceSerial Plate Location Product RecordCooktop Features Readthese iNSTRUCTiONS Carefully Before Using the CooktopUsing the Griddle Surface CookingINCORRECT Setting Surface Controls General Cooktop information About the Ceramic Glass CooktopSetting Surface Controls contd Using the Touch ControlControls Available Esec Window Display Settings ContdRecommended Operating Single Radiant Surface Elements To Operate the Single Radiant Surface ElementsOuter Warm & Hold Feature Operating the Bridge Surface ElementTo Operate the Bridge Surface Element Setting Sabbath Feature ModeMinuteTimer ControlsGeneral Care & Cleaning Never store any cookware on the cooktopCleaning Recommendations for the Ceramic Glass Cooktop Before You Call OperateMaster Protection Agreements Acuerdos maestros de protecci6nYour Home MY-HOMEOur Home Canada

790.4281, 790.4282 specifications

The Kenmore 790.4282 and 790.4281 are standout models in Kenmore's range of gas ranges, designed for those who seek reliability and efficiency in their cooking experiences. Renowned for their blend of advanced features and practical design, these ranges deliver both quality and convenience for home chefs.

One of the significant characteristics of the Kenmore 790 series is its spacious oven capacity. Both models boast a generous oven size, allowing home cooks to tackle large meals effortlessly. Whether you are roasting a turkey or baking multiple trays of cookies, the ample space ensures that you can cook for gatherings without feeling constrained.

The models feature a powerful gas cooktop equipped with multiple burners, each designed to cater to various cooking needs. With high BTU power burners, rapid boiling, searing meats, and sautéing vegetables become quicker and more efficient. Additionally, the range includes simmer burners for delicate sauces and perfecting custards, making these units versatile for diverse culinary tasks.

In terms of technology, the Kenmore 790.4282 and 790.4281 integrate an electronic ignition system that eliminates the need for matches or lighters, enhancing safety while also reducing energy consumption. This technology ensures that the burners ignite quickly and reliably, providing immediate heat as needed.

Both models come with a self-cleaning oven feature, simplifying maintenance. This function uses high temperatures to burn off food residues, allowing for easy cleanup without harsh chemicals. Furthermore, the ranges are equipped with various cooking modes, including bake, broil, and convection, enabling users to choose the optimal method for their recipes.

The control panel is user-friendly, featuring intuitive knobs and a digital display. This design facilitates effortless adjustments to temperature and cooking times, catering to chefs of all skill levels. Additionally, the bright interior oven light allows for easy monitoring without the need to open the door, which can save energy and maintain consistent temperatures.

Another notable feature is the stainless steel finish, which not only provides a modern, sophisticated look but also enhances durability and ease of cleaning. This finish helps the range resist fingerprints and smudges, keeping it looking pristine.

In conclusion, the Kenmore 790.4282 and 790.4281 are exemplary gas ranges that combine innovative technology with practical features, catering to the needs of every home cook. Their spacious ovens, versatile cooktops, user-friendly controls, and self-cleaning capabilities make them a valuable addition to any kitchen, blending functionality with style.