Kenmore 795-71022.010 Check to normality by measurement of Voltage, Standard for normality

Page 20

2) Check to normality by measurement of Voltage

Measure the resistance between pin of the connector (as shown picture) with a multi-tester.

<Fig. 1>

<Fig. 1>

Standard for normality

-In order to decide whether compressor operating is normal or not, check the output transfer during the refrigerator operation.

-After input the initial power and compressor operates, wait for 10 minutes to estimate.

-Compressor operation may be diagnosed as normal if the voltage falls between 145V and 180V.

Warning

1.Please be cautious of electric shock and short (it is estimated after turning on initial power).

2.If the voltage is estimated less than 80V, it is diagnosed as bad.

3) Check problems by LED On & Off Count _ (Sub PCB)

If compressor protection logic is running, LED Lamp’s blinking frequency of sub PCB, which takes in charge of control, can help estimate the protection logic’s symptoms and the cause of its problems.

Trip name

Led Times

Comp Off Time

Stroke Trip

2

1min

Current Trip

6

6min

 

 

 

Lock Piston Trip

5

2min 30sec

 

 

 

IPM fault trip

7

20sec

 

 

 

-Current Trip PCB defects or Cycle clogging maybe the causes. After estimating winding resistance, estimate compressor operation voltage to check if there is any problem and take actions to repair cycle at replacement of compressor.

-Stroke Trip can occur when the surrounding temperature is high, C-Fan, F-Fan and so on are constrained, or when cycle problems, such as moisture blocking or compressor defect, are related.

-Lock Piston Trip Since compressor itself can be a potential cause of a defect, estimate the compressor resistance value according to #1’s compressor winding value estimation method and estimate the #2’s compressor operation voltage to decide whether it is defective or not

(Before replacement of compressor, replace PCB and conduct the replacement of compressor during compressor replacement)

-IPM fault Trip Replace sub PCB since there is high chance that it is caused by sub PCB’s part defect.

- 20 -

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Model #s Contents Electrical Specifications InstallationReplacement Parts Important NoticeDescription 795.710 Parts Identification Removing and Replacing Refrigerator Doors Electrical Shock HazardTo remove the left refrigerator door To remove the right refrigerator doorDoor Replace door frame cover Door AlignmentFAN and FAN Motorevaporator Refrigerator Compartment Lamp Defrost Control AssemblyLamp Multi Duct Main PWBDispenser To change freezer lightDisplay PWB Replacement Duct Door ReplacementFunnel Replacement SUB PWB for Working DispenserAuger Motor Cover ICE Corner Door ReplacementIcemaker Assembly HOW to Remove a Door ICE BIN HOW to Insert a Door ICE BINHOW to Remove and Reinstall the Pullout Drawer Follow Steps to RemoveFollow Steps to Reinstall Water Valve Disassembly Method FAN and FAN Motor Disassembly MethodPull OUT Drawer HookControl of Compressor Block Diagram CompressorIntroduction of E-Linear Compressor RoleCheck to normality by measurement of resistance Compressor problems diagnosisCompressor protection logic Standard for normality Check problems by LED On & Off Count Sub PCBCheck to normality by measurement of Voltage Circuit Diagram Troubleshooting Error Code on display panelCON5 CON8 CON1 CON4 CON3CON2 CON3 CON1 Sub PCB EBR60070706 2010.02~CON4 Temperature Result Temperature For exampleSensor is determined by Indicates -4FIndicates 32F CON101 Temperature Result DisplayCheck the Brown to Brown Temperature Result CON4Check the Defrost control part Fuse DefrostSensor Defrost HeaterBelow 12 Change the PCB Or 5 Change the motor Check the Fan motor voltage Result SVC Action Below 10 Change the PCB Or 5 Change the motor CON5 Check the White/Red to White/Black Result SVC Action CON5CON2 Check the resistance value Point Result SVC Action Ice Maker Geared Motor Dispenser MotorIce Maker Geared MotorResult SVC Action While pushing the lever S/W CON2 Check the Blue to GrayCON3 Check the resistance value Point Result SVC Action Dispenser Ice Maker Pilot ValveCheck the Yellow Blue to Sky blue Status Result SVC Action CON4 Check the Blue to Black Status Result SVC ActionNormal Go to Other Change door S/W Push Infinity Page Damper Check the air temperature Status SVC Action Cold or not ? For example, 23 indicates -4FPage AC TPA DC TPA After measure the values, you should put in the TPA againPage Page How to check the Fan-Error Compressor Troubleshooting LED operating condition Cause Service guideline LED seven- time repetiton IPM Fault TripLED two time Repetiton Stroke Trip On on off on on off on on off repeatingDefrost Controller Assembly Function How to Measure SensorStandard Fuse-M at all temperature Sensor at room temperatureSheath heater at all temperature StandardTest Point Ressult Measure Button Plunger Beep Standard Multimeter beep Switch F,RSwitch, Refrigerator Dispenser DC Motor Function Standard Geared Motor Cube SolenoidStandard Damper Test Points Result To 2 and 3 to How to Measure Flow Sensor FunctionVvvf Information of Linear CompressorCvcf FCT0 IPM Voltage Check Multi TesterFC75LANE LG Linear Compressor Inf ~ ~ 8 Ω ~ 8 Ω Inf ~Service Diagnosis Chart Complaint Points to be Checked RemedyTroubleshooting Chart Refrigeration CyclePartialFrost Very FastOperation Principle Stage Time to Supply Indications Remarks ICE Maker FunctionsWater supply amount Table Defect Diagnosis Function Stage Items Indicator RemarksDivision Indicator Contents Remarks How to Toggle the Display between F & C FunctionFunction Lock function dispenser and display button lockUltra Ice selection Dispenser use selectionCooling Fan Motor Ice Compartment FanUltra Ice Alarm for Open DoorHow to set the display mode and cancel It Defrosting removing frost Defect Diagnosis Function617A 625A 616G 623B Case Parts Case Parts Case Parts Freezer Parts Refrigerator Parts Door Parts Door Parts Dispenser Parts ICE Maker & ICE Bank Parts

795-71022.010 specifications

The Kenmore 795-71022.010 is a standout refrigerator that embodies functionality, style, and advanced technology. Designed with the modern consumer in mind, this model brings both aesthetic appeal and practical features to enhance your kitchen experience.

One of the most notable characteristics of the Kenmore 795-71022.010 is its spacious interior, boasting a capacity of 28 cubic feet. This provides ample storage space for groceries, leftovers, and beverages, making it ideal for families of all sizes. The refrigerator features a French door design that not only adds a touch of elegance but also offers easier access to the interior. The lower freezer drawer is equipped with a pull-out bin, which allows for quick retrieval of frozen items.

A key technological feature of this model is its SmartCooling System. This advanced cooling technology utilizes multiple sensors strategically placed throughout the refrigerator to ensure that food stays fresh longer. By constantly monitoring internal temperatures and adjusting accordingly, it effectively maintains optimum humidity levels. Additionally, the linear compressor provides reliable cooling while reducing energy consumption, making it an eco-friendly choice.

Another highlight of the Kenmore 795-71022.010 is its Smart Technology compatibility. With Wi-Fi connectivity, users can remotely monitor and control the refrigerator through a smartphone app. This feature enables you to check the temperature, receive alerts for any issues, and even adjust settings while away from home. This level of connectivity is particularly beneficial for busy households.

The interior of this refrigerator is designed for maximum organization. Adjustable shelves and various door bins allow users to customize the layout according to their needs. LED lighting illuminates the interior, making it easy to find items even in low light conditions. The humidity-controlled crisper drawers are designed to keep fruits and vegetables fresher for longer, preserving their flavor and nutritional value.

In terms of energy efficiency, the Kenmore 795-71022.010 is Energy Star certified, meaning it meets strict energy efficiency guidelines. This not only helps in reducing utility bills but also supports environmental sustainability.

In conclusion, the Kenmore 795-71022.010 combines spaciousness, innovative technology, and energy efficiency in a sleek design. Its smart features, organization capabilities, and reliable cooling system make it an excellent investment for any modern kitchen. Whether you are a culinary enthusiast or a busy family, this refrigerator offers the versatility and performance needed to keep your food fresh and accessible.
Top Page Image Contents