Recommended Method For Splicing Wires

Read the following wiring instructions very carefully. If you have any trouble understanding any of these instructions, have the amplifier professionally installed by an experienced technician. Incorrect wiring will prevent the amplifier from operating, or will damage the amplifier.

Strip 1/2" of insulation from the ends of the wires..

Twist together and bend as shown.

Wrap with electrical tape.

1.Power Terminal

1.DISCONNECT THE VEHICLE’S NEGATIVE (-) BATTERY TERMINAL FROM THE NEGATIVE BATTERY POST.

2.Strip ½" of insulation from the end of the 8 gauge power wire. Connect the 8 gauge power wire to the after-market positive battery terminal according to the manufacturer's installation instructions.

After Market Positive Terminal (+)
To Amplifier Power Terminal
In-line 35 amp Fuse or Circuit Breaker	Vehicle's Positive (+)
In-line 35 amp Fuse or Circuit Breaker	12 Volt power cable
(not included)

3.Install a 35 amp fuse or 35 amp circuit breaker in the 8 gauge power wire as close to the battery as practical.

4.Then route the 8 gauge power wire from the 30 amp fuse or circuit breaker to the rear of the amplifier.

5.Strip 1/2" width of insulation from the end of the 8 gauge power wire.

6.Attach a spade lug on the end of 8 Gauge wire.

7.Loosen screw to open POWER connector plates on rear of amplifier.

8.Insert the spade lug between between the connector plates. Turn screw until power cable is tight.

2.Remote Terminal

The REMOTE wire connection automatically turns on your amplifier when your stereo is turned on.

On most stereos, this wire is marked as the REMOTE, ACCESSORY, or POWER ANTENNA.

1.Locate the REMOTE, ACCESSORY, or POWER ANTENNA on the stereo. (Refer to your stereo owner's manual.)

2.Splice REMOTE, ACCESSORY or POWER ANTENNA wire from rear of the stereo to a length of wire that will reach the rear of the amplifier

3.Loosen screw and open REMOTE connector plates on rear of amplifier.

4.Insert wire end between the REMOTE connector plates.

5.Tighten screw closing REMOTE connector plates on wire.

3.Ground Terminal

1. The ground connection cable should be attached to clean, unpainted chassis metal for a good electrical connection.

2.Find good, non-rusted chassis metal, as close to the amplifier as possible.

3.Drill a pilot hole with a 1/16" drill bit.

4.Use sandpaper to expose an area of bare metal around the pilot hole about the size of a dime.

5.Tightly fasten the provided ground cable with the self tapping sheet metal screw to the chassis metal. A loose ground will cause distortion and popping noises in the speakers.

You may purchase shielded RCA cables that have a remote wire that is built right into the cable. This type of cable makes it possible to route both RCA cable and remote wire at the same time.

Recommended Method For Attaching Wires to Terminals

1. POWER WIRE

When connecting the power wire, place the spade terminal under the contact plate and the forks around the screw. Then tighten the screw.

2. REMOTE WIRE

To connect the remote wire, place the twisted end under the contact plate and tighten screw.

3. GROUND WIRE
To connect the supplied ground wire,
remove the screw and contact from the
ground terminal on the rear of the amplifier.
Put the screw through the contact plate,		3. GROUND WIRE
then through the ground wire, and finally	1. POWER WIRE	2. REMOTE WIRE
tighten the screw.	1. POWER WIRE	2. REMOTE WIRE
tighten the screw.

VRA1.0 specifications

The Roadmaster VRA1.0 is a cutting-edge vehicle routing and navigation assistant designed to enhance the efficiency and safety of driving experiences. Combining innovative technologies with user-friendly features, this device stands out as an essential tool for both professional drivers and everyday commuters.

One of the main features of the Roadmaster VRA1.0 is its advanced GPS navigation system, which offers real-time traffic updates and provides alternative routes to avoid congestion. This capability not only saves time but also reduces fuel consumption, making it an eco-friendly option for those who spend considerable hours on the road. The device seamlessly integrates with satellite systems, ensuring accurate positioning and directions at all times.

The Roadmaster VRA1.0 is equipped with an intuitive touchscreen interface that allows users to easily input destinations and access various navigation settings. The interface is designed with usability in mind, ensuring that drivers can quickly and safely interact with the device while on the move. Voice command functionality further enhances the user experience, allowing drivers to keep their hands on the wheel and eyes on the road.

Another significant characteristic of the Roadmaster VRA1.0 is its compatibility with smartphone applications. By connecting via Bluetooth, users can access their favorite apps for music, messages, and more. This integration promotes a more connected driving experience while maintaining the focus on safety and convenience.

In addition to its navigation features, the Roadmaster VRA1.0 also prioritizes driver safety. It includes built-in alerts for speed limits, road hazards, and potential collisions, helping drivers make informed decisions and ensuring they stay within legal parameters. Furthermore, it provides emergency response functions that can be activated with a simple command, connecting users to emergency services if needed.

The device is designed to be rugged and weather-resistant, making it suitable for various driving conditions. Whether navigating city streets or rural backroads, the Roadmaster VRA1.0 is built to withstand the elements while delivering reliable performance.

In conclusion, the Roadmaster VRA1.0 is a versatile vehicle routing and navigation assistant that combines cutting-edge technology with practical features. Its advanced GPS capabilities, user-friendly interface, smartphone integration, and safety features make it an indispensable companion for drivers seeking to enhance their travel experience. Whether commuting for work or embarking on an adventurous road trip, the Roadmaster VRA1.0 stands ready to guide you every mile of the way.