Makita G7301R, G7300R manuel dutilisation Wattage Information, － 22－

Page 28

6. WATTAGE INFORMATION

Some appliances need a "surge" of energy when starting.

This means that the amount of electrical power needed to start the appliance may exceed the amount needed to maintain its use.

Electrical appliances and tools normally come with a label indicating voltage, cycles / Hz, amperage (amps) and electrical power needed to run the appliance or tool.

Check with your nearest dealer or service center with questions regarding power surge of certain appliances or power tools.

■Electrical loads such as incandescent lamps and hot plates require the same wattage to start as is needed to maintain use.

■Loads such as fluorescent lamps require 1.2 to 2 times the indicated wattage during start-up.

■Loads for mercury lamps require 2 to 3 times the indicated wattage during start-up.

■Electrical motors require a large starting current. Power requirements depend on the type of motor and its use. Once enough "surge" is attained to start the motor,

the appliance will require only 50% to 30% of the wattage to continue running.

■Most electrical tools require 1.2 to 3 times their wattage for running under load during use. For example, a 5,000 watt generator can power a 1800 to 4000 watt electrical tool.

■Loads such as submersible pumps and air compressors require a very large force to start. They need 3 to 5 times the normal running wattage in order to start.

For example, a 5,000 watt generator would only be able to drive a 1,000 to 1,700 watt pump.

NOTE :

The following wattage chart is general guide only. Refer to your specific appliance for correct wattage.

To determine the total wattage required to run a particular electrical appliance or tool, multiply the voltage figure of the appliance/tool by the amperage (amps) figure of same. The voltage and amperage (amps) information can be found on a name plate which is normally attached to electrical appliances and tools.

Applications

Applicable Wattage (W)

 

60Hz

 

 

 

Incandescent lamp, Heater

6000

 

 

Fluorescent lamp, Electric tool

3000

 

 

Mercury lamp

2000

 

 

Pump, Compressor

1400

 

 

－ 22－

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Generator Federal Emissions Component Defect Warranty Emission Component Defect Warranty PeriodOwners Warranty Responsibilities Factory Service Centers in Canada British Columbia Richmond Vancouver Regional OfficeForeword ［CAUTION］Contents Safety Precautions － 1－－ 2－ ［CAUTION］Specifications － 3－Components － 4－Control Panel － 5－Check Engine OIL PRE-OPERATION Checks－ 6－ Check Engine Fuel － 7－Battery Installtion RED CableBlack Cable － 8－－ 9－ Grounding Generator Checking Component PartsCheck Generator Surroundings － 10－Starting Operating Procedures－ 11－ ［Electric starter model］ － 12－AC Application Using Electric Power－ 13－ － 14－ － 15－ Style Ampere Receptacle AC plug DescriptionGfci Receptacle Full Power Switch－ 16－ Connecting to Domestic Circuits House Wiring － 17－－ 18－ Safety Precautions While Charging DC ApplicationConnection of Cable － 19－OIL Sensor Stopping－ 20－ HOW to USE Idle Control Idle ControlChecking the Operation Stopping the EngineWattage Information － 22－Voltage Drop in Electric Extension Cords － 23－Spark Arrester Spark Arrester－ 24－ Maintenance Schedule Periodic MaintenanceDaily Inspection － 25－Periodic Maintenance Schedule table － 26－HOW-TO Maintenance Cleaning AIR CleanerEngine OIL Change － 27－Cleaning and Adjusting Spark Plug Cleaning Fuel StrainerFuel Hose Replacement － 28－Checking Carbon Brush － 29－Preparation for Storage － 30－Troubleshooting － 31－Wiring Diagram － 33－ Optional Parts HOW to Install the WHEEL, Handle and Roof Pipe－ 34－ Page Makita Corporation

G7300R, G7301R specifications

The Makita G7301R and G7300R are two exceptional tools that represent the brand's commitment to power and performance in the realm of industrial machinery. These models are designed for heavy-duty applications, making them ideal for professionals who demand reliability and efficiency.

At the heart of both models is a robust motor that delivers high torque, allowing users to tackle tough jobs with ease. The G7301R boasts an advanced 2000-watt motor, while the G7300R features a slightly lower wattage but is no less effective. Both motors are engineered for maximum performance and longevity, ensuring that they can withstand the rigors of daily use in commercial and industrial settings.

One of the standout features of these tools is their ergonomic design. Makita has prioritized user comfort with rubberized grips that reduce fatigue during extended use. The lightweight yet durable construction of both models allows for easy maneuverability, making them suitable for various tasks, from grinding to cutting.

Additionally, these tools incorporate advanced cooling systems that prevent overheating, extending their lifespan significantly. The ventilation design ensures optimal air intake and exhaust, minimizing the risk of damage during prolonged operation. This technology provides users with peace of mind, knowing that their equipment will perform reliably throughout demanding projects.

Safety is another crucial aspect of the G7301R and G7300R. Both models come equipped with multiple safety features, including overload protection, which automatically shuts down the motor when it detects excessive strain. This not only protects the tool but also ensures the user's safety by reducing the risk of accidents.

In terms of versatility, both models support a wide range of attachments and accessories, making them highly adaptable for different tasks. Whether you need to grind, polish, or cut, the Makita G7301R and G7300R can accommodate a variety of applications, further enhancing their utility for professional use.

In conclusion, the Makita G7301R and G7300R are prime examples of innovative engineering, providing users with powerful, reliable, and versatile tools designed for a range of heavy-duty applications. With their combination of advanced technology, ergonomic design, and safety features, these models stand out as must-have equipment for any serious tradesperson or contractor looking to elevate their work quality and efficiency.
Top Page Image Contents