Trimmer Line Advance, Cutting Methods | Weed Eater XT300 instruction

TRIMMER LINE ADVANCE

The trimmer line will advance approximately 2 in. (5 cm) each time the bottom of the trimmer head is tapped on the ground with the engine running at full throttle.

The most efficient line length is the maximum length allowed by the line limiter.Always keep the shield in place when the tool is being oper- ated.

To advance line:

SOperate the engine at full throttle.

SHold the trimmer head parallel to and above the grassy area.

STap the bottom of the trimmer head lightly on the ground one time. Approximately 2 in. (5 cm) of line will be advanced with each tap.

Always tap the trimmer head on a grassy area. Tapping on surfaces such as concrete or asphalt can cause excessive wear to the trimmer head.

If the line is worn down to 2 inches (5 cm) or less, more than one tap will be required to ob- tain the most efficient line length.

WARNING: Use only 0.080” (2 mm) diameter line. Other sizes and shapes of line will not advance properly and will result in im- proper cutting head function or can cause se- rious injury. Do not use other materials such as wire, string, rope, etc. Wire can break off during cutting and become a dangerous mis- sile that can cause serious injury.

CUTTING METHODS

WARNING: Use minimum speed and do not crowd the line when cutting around hard objects (rock, gravel, fence posts, etc.), which can damage the trimmer head, become entangled in the line, or be thrown causing a serious hazard.

SThe tip of the line does the cutting. You will achieve the best performance and mini- mum line wear by not crowding the line into the cutting area. The right and wrong ways are shown below.

Tip of the Line

Line Crowded Into

Does The Cutting

Work Area

Right

Wrong

S The line will easily remove grass and weeds from around walls, fences, trees and flower beds, but it also can cut the tender bark of trees or shrubs and scar fences. To help avoid damage especially to delicate vegetation or trees with tender bark, shorten line to 4--5 in. (10--13 cm) and use at less than full throttle.

SFor trimming or scalping, use less than full throttle to increase line life and decrease head wear, especially:

S During light duty cutting.

S Near objects around which the line can wrap such as small posts, trees or fence wire.

SFor mowing or sweeping, use full throttle for a good clean job.

TRIMMING -- Hold the bottom of the trimmer head about 3 in. (8 cm) above the ground and at an angle. Allow only the tip of the line to make contact. Do not force trimmer line into work area.

Trimming

3 in. (8 cm) Above Ground

SCALPING -- The scalping technique re- moves unwanted vegetationdown to the ground. Hold the bottom of the trimmer head about 3 in. (8 cm) above the ground and at an angle. Allow the tip of the line to strike the ground around trees, posts, monuments, etc. This technique increases line wear.

Scalping

MOWING -- Your trimmer is ideal for mowing in places conventional lawn mowers cannot reach. In the mowing position, keep the line parallel to the ground. Avoid pressing the head into the ground as this can scalp the ground and damage the tool.

Mowing

SWEEPING -- The fanning action of the rotat- ing line can be used for a quick and easy clean up. Keep the line parallel to and above the surfaces being swept and move the tool from side to side.

Sweeping

XT300 specifications

The Weed Eater XT300 is a versatile and powerful string trimmer designed to make yard work more efficient and manageable. With its blend of innovative features and advanced technologies, it stands out as an essential tool for both casual gardeners and professional landscapers alike.

One of the main features of the XT300 is its robust 30cc two-cycle engine, which provides ample power to tackle even the toughest overgrowth. This engine is designed for optimal performance, delivering a smooth and consistent power output that allows you to cut through thick grass and weeds with ease. Additionally, the XT300’s lightweight design makes it easy to maneuver, reducing user fatigue during extended periods of operation.

Another noteworthy characteristic of the XT300 is its Easy Start system. This technology simplifies the starting process, allowing users to get to work quickly without the frustration often associated with recoil starters. With just a few gentle pulls, the engine fires up, making it ideal for users of all experience levels.

The XT300 also features a 17-inch cutting swath, enabling efficient trimming of large areas in a single pass. This wide cutting path reduces the time and effort required to complete your yard maintenance tasks, making it a time-saving asset. The trimmer is equipped with a bump feed head that allows for quick and efficient line advancement, ensuring that you can continue working without the need for constant interruptions.

Durability is another key aspect of the XT300, as its construction includes high-quality materials designed to withstand the rigors of outdoor use. The trimmer’s solid build means that it can handle bumps and scrapes without compromising performance over time. Safety features, including a protective guard, further enhance its usability while providing peace of mind during operation.

Additionally, the ergonomic design of the XT300 includes an adjustable handle that provides comfort and control, enabling users to trim with precision even in hard-to-reach areas. The balance and lightweight nature of the trimmer contribute to its ease of use, making it suitable for users of all physical capabilities.

In summary, the Weed Eater XT300 is a powerful and reliable string trimmer perfect for any landscaping job. With its features like a potent engine, Easy Start technology, a generous cutting swath, and an emphasis on comfort and durability, this tool is built to help you maintain a well-groomed yard with ease and efficiency.