Murray 425603x99A HOW to USE the Speed Control Pedal, HOW to Disconnect the Transmission, To 1/2

Page 16

OPERATION

HOW TO USE THE SPEED CONTROL PEDAL

The drive system uses a Hydrostatic Automatic Drive transmission. The Hydrostatic transmission is very easy to operate. This type of drive system does not require a shift lever or a clutch pedal.

The speed and direction of travel is controlled by a single speed control pedal operated with your right foot. Do not use the left brake pedal in normal operation. Only use the left brake pedal to quickly stop in an emergency.

HOW TO DRIVE FORWARD

1.The automatic drive disconnect must be in the DRIVE position (Figure 7).

2.Slowly release your left foot from the brake pedal.

3.Move the throttle control to the FAST position.

4.Slowly push the speed control pedal forward to the desired speed (Figure 6).

5.To increase forward speed, slowly move the speed control pedal forward. To reduce forward speed, slowly release the speed control pedal until the unit slows to the desired speed.

Speed Control

Pedal

Figure 6

HOW TO DRIVE IN REVERSE

1.Look to the rear.

2.Slowly push the speed control pedal to the REVERSE position.

HOW TO CHANGE DIRECTIONS

CAUTION: To change directions, do not use the left brake pedal. Use only the speed control pedal.

1.Slowly remove your foot from the speed control pedal. The speed control pedal will automatically return to the NEUTRAL position.

2.When the unit stops, slowly move the speed control pedal to the desired direction.

SPEED CONTROL PEDAL POSITIONS

The forward speed is controlled by the position of the speed control pedal. The following chart provides functions along with the pedal positions. Always operate the engine with the throttle control in the FAST position.

FUNCTION

PEDAL

THROTTLE

 

POSITION

 

 

 

 

Trimming

1/3

 

Snow Thrower

 

 

 

 

 

Bagging Grass

1/3 to 1/2

 

 

 

FAST

 

 

CHOKE

Normal Mowing

1/2 to 2/3

FAST

 

 

 

 

SLOW

Easy Mowing

1/2 to 3/4

THROTTLE

Snow Blade

 

 

 

 

Transport

FULL

 

 

 

 

Pull Behind

1/3 to 1/2

 

Attachments

 

 

 

 

 

HOW TO DISCONNECT THE TRANSMISSION

To push the unit, use the automatic drive disconnect to release the transmission. The automatic drive disconnect is under the seat.

1.The engine must be off.

2.Raise the seat. The automatic drive disconnect is under the seat.

3.Move and latch the automatic drive disconnect in the PUSH position (Figure 7). The transmission is now released and the unit can be pushed.

NOTE: In cold weather, the heavy viscosity oil in the transmission will make the unit difficult to push.

4.To engage the transmission, unlatch the automatic drive dis- connect. The transmission is now connected and ready to op- erate.

Automatic Drive Disconnect

PUSH POSITION

Seat

Automatic Drive Disconnect

DRIVE POSITION

Figure 7

F–030738L

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model Table of Contents Environmental Awareness OWNER’S InformationSafe Operation Practices for Ride-on Mowers II. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Steps to Follow Before MowingSafety Warning Pictorials International PictorialsInternational Pictorials Control And Operating PictorialsAssembly AssemblyHOW to Install the Seat HOW to Assemble the Steering Wheel100105417x47 25x3 17x146Maintenance Free Battery HOW to Charge Maintenance Free BatteryHOW to Install the Battery Cables Remove the battery and battery trayHOW to Prepare the Engine Check the Level of the Mower HousingIMPORTANT! Before YOU Start Mowing Check the TiresOperation Location of ControlsHOW to USE the Throttle Control AttachmentsHOW to USE the Speed Control Pedal HOW to Disconnect the TransmissionTo 1/2 To 2/3HOW to SET the Parking Brake HOW to Change the Cutting HeightHOW to Stop the Unit HOW to Transport the UnitHOW to Operate with the Mower Housing HOW to Operate the Unit on HillsBefore Starting the Engine HOW to Start the EngineCarburetor Operating Tips Mowing and Bagging TipsMaintenance Frequency Maintenance Required CommentsHOW to Check the Muffler General RecommendationsHOW to Remove and Install the Blade HOW to Sharpen the BladeInspect Blade Mount the blade and blade adapter on the mandrelHOW to Adjust the Blade Rotation Control HOW to Check and Adjust the Motion Drive Belt Remove the 1/4 inch 6 mm pin or bolt FigureHOW to Check and Adjust the Drive Brake Disconnect the red cable from the positive + terminalWhere to Lubricate HOW to Check the Fuel FilterHOW to Install the Mower Housing HOW to Remove the Mower HousingRemove the mower drive belt from the stack pulley Lift Lever Hole No Position No HOW to Adjust the Gauge Wheels5,6 HOW to Level the Mower Housing Install the mid-idler pulley HOW to Replace the Motion Drive BeltRemove the mid-idler pulley HOW to Replace the Mower Drive Belt HOW to Install the Wheels Fasten the rear wheel with washer and e-ringHOW to Replace the Fuse HOW to Replace the Light BulbHOW to Clean the Mower Housing BatteryTrouble Shooting Chart 030738L USARepair Parts Chassis & HoodKey Description Drive Assembly Drive Assembly Steering Repair Parts Mower Housing Suspension Repair Parts Mower Housing 7601032 Model 425603x99AREPAIR Parts Engine Mount Assembly Engine Mount Assembly Repair Parts Electrical System Electrical System Key Part Description030738L Index Model No Model No Bushel Capacity

425603x99A specifications

Murray 425603x99A is a significant advancement in the field of outdoor power equipment, combining innovative technologies with user-centric features to deliver an exceptional performance. This model is primarily designed for tackling heavy-duty landscaping tasks with efficiency and ease, making it a top choice among both professional landscapers and avid gardeners.

One of the standout features of the Murray 425603x99A is its powerful engine. Equipped with a robust four-stroke engine, this model offers high torque and reliable power, ensuring that it can handle challenging terrains and thick underbrush without faltering. The engine is not only powerful but also designed with fuel efficiency in mind, allowing users to complete more tasks on less fuel, which is both cost-effective and environmentally friendly.

The design of the Murray 425603x99A emphasizes user comfort and control. Its ergonomic handlebar system provides a comfortable grip and reduces vibrations, minimizing fatigue during extended periods of use. The adjustable height feature allows operators to customize the machine to suit their specific working conditions and personal preferences, enhancing overall user experience.

In terms of cutting technology, the Murray 425603x99A comes with a precision cutting deck that ensures clean and even cuts across various grass types. The deck’s design promotes excellent grass discharge performance, making it easy to manage clippings while maintaining a pristine lawn appearance. Additionally, the mower features multiple cutting height adjustments, providing versatility from a low trim to a more substantial grass length.

Safety is a critical consideration in the design of the Murray 425603x99A. It includes several safety features, such as an automatic shut-off function that engages when the operator releases the handle, preventing accidental starts. The sturdy construction of the mower also adds to its durability, ensuring that it can withstand the rigors of frequent use.

Moreover, the Murray 425603x99A is compatible with a range of accessories, allowing for personalized modifications to its functionality. Users can equip it with baggers, mulchers, and other attachments to enhance its versatility across different tasks.

Overall, the Murray 425603x99A stands out as a well-engineered and dependable outdoor power equipment choice. Its combination of power, precision, and thoughtful design features make it an excellent investment for anyone seeking durability and performance in their landscaping endeavors. Whether for commercial or residential use, this model promises to deliver results that exceed expectations.
Top Page Image Contents