Murray 405005x99A manual Before Starting the Engine, Carburetor, HOW to Start the Engine

Page 18

OPERATION

BEFORE STARTING THE ENGINE

CHECK THE OIL

NOTE: The engine was shipped from the factory filled with oil. Check the level of the oil. Add oil as needed. See the engine manufacturer’s instructions for the type of gasoline and oil to use.

1.Make sure the unit is level.

NOTE: Do not check the level of the oil while the engine runs.

2.Check the oil. Follow the procedure in the engine manufactur- er’s instructions.

3.If necessary, add oil until the oil reaches the FULL mark on the dipstick. The quantity of oil needed from ADD to FULL is shown on the dipstick. Do not add too much oil.

CAUTION: A mixture of alcohol (ethanol or methanol) and gasoline (called gasohol), will attract moisture and cause acid deposits during storage. While the unit is in storage, the acids in the fuel can damage the fuel system.

To prevent engine problems with the fuel system, empty the fuel system before storage of 30 days or longer as follows.

1.Drain the fuel tank.

2.Start the engine. Let the engine run until the fuel lines and the carburetor are empty.

3.After storage, make sure you use fresh fuel. See the storage instructions for additional information.

4.Never use engine cleaner or carburetor cleaner in the fuel tank or permanent damage can occur.

ADD GASOLINE

WARNING: Always use a safety gasoline container. Do not smoke when adding gasoline to the fuel tank. Do not add gasoline when you are inside an enclo- sure. Before you add gasoline, stop the engine and let the engine cool for several minutes.

Fill the

fuel tank with regular

Fuel Tank

unleaded gasoline. Do not use

Full

premium

unleaded gasoline.

Make sure the gasoline is fresh

 

and clean. Leaded gasoline will

 

increase

deposits and shorten

 

the life of the valves.

CARBURETOR

The factory settings for the carburetor are for most conditions. If the engine is operated under the following conditions, you can adjust the carburetor mixture. To adjust the carburetor, see the engine manufacturer’s instructions.

1.The engine has a loss of power or does not run smooth.

2.A change from summer to winter operation.

3.A 40 degree change in the operation temperature. The carbure- tor was adjusted at 80 degrees at the factory.

4.The engine is operated above 4,000 feet.

HOW TO START THE ENGINE

WARNING: The electrical system has an operator presence system that includes a sensor switch for the seat. These components tell the electrical system if the operator is sitting on the seat. This system will stop the engine when the operator leaves the seat if the blade rotation control is engaged or if the trans- mission is engaged. For your protection, always make sure this system operates correctly.

NOTE: The engine will not start unless you depress the clutch/brake pedal or engage the parking brake and move the blade rotation control to the DISENGAGE position.

1.Push the clutch/brake pedal completely forward. Keep your foot on the pedal.

2.Move the shift lever to the neutral (N) position.

3.Make sure the blade rotation control is in the DISENGAGE position.

4.Move the throttle control completely forward to the CHOKE or FAST position. Some models have a separate choke knob. Pull the choke knob to the full CHOKE position.

5.Turn the ignition key to the START position. Release the key when the engine starts.

NOTE: If the engine does not start after four or five tries, see the TROUBLE SHOOTING CHART.

6.Slowly move the throttle control to the SLOW position.

7.Let a cold engine run for several minutes. Begin work when the engine is warm. To start a hot engine, move the throttle control to a position between FAST and SLOW.

F–030725L

18

Image 18
Contents Model Table of Contents OWNER’S Information Responsibility of the OwnerII. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Steps to Follow Before MowingInternational Pictorials International PictorialsAssembly AssemblyHOW to Install the Seat HOW to Assemble the Steering WheelMaintenance Free Battery HOW to Charge Maintenance Free BatteryHOW to Install the Battery Cables IMPORTANT! Before YOU Start Mowing HOW to Prepare the EngineCheck the Level of the Mower Housing Check the TiresOperation Location of ControlsLift Lever HOW to USE the Throttle Control HOW to USE the Shift LeverAttachments HOW to Stop the Unit HOW to SET the Parking BrakeHOW to Change the Cutting Height HOW to Transport the UnitHOW to Operate with the Mower Housing HOW to Operate the Unit on HillsHOW to Start the Engine Before Starting the EngineCarburetor Operating Tips Mowing and Bagging TipsHOW to Check the Muffler MaintenanceMaintenance Chart General RecommendationsHOW to Remove and Install the Blade HOW to Sharpen the BladeInspect Blade HOW to Adjust the Blade Rotation Control HOW to Check and Adjust the Clutch HOW to Check and Adjust the Drive BrakeHOW to Adjust the Shift Lever Disconnect the adjuster nut from the shifter bracket FigureWhere to Lubricate HOW to Check the Fuel FilterHOW to Remove the Mower Housing HOW to Install the Mower HousingHOW to Level the Mower Housing HOW to Replace Motion Drive Belt RemovalInstallation HOW to Replace the Mower Drive Belt HOW to Install the Wheels Front WheelHOW to Clean the Mower Housing HOW to Replace the FuseHOW to Replace the Light Bulb BatteryTrouble Shooting Chart Problem The engine will not startMURRAY, INC. Lawn Mower Central Parts Distributors 030725L Repair Parts Chassis & HoodKey Description Motion Drive Motion Drive Steering Steering Mower Housing Suspension Repair Parts Mower Housing 7601044 Repair Parts Engine Mount Engine Mount Repair Parts Electrical System Electrical System Key Part Description030725L Index Lawn Tractor Accessories