Type, Trimability, Blades, Anti-Scalp | Toro 3320, 3280-D specification

Groundsmaster® 3280-D & 3320 Accessories Specifications*

TYPE

MOWING RATE [1]

TRIMABILITY

HEIGHT OF CUT

CONSTRUCTION

SPINDLE

ASSEMBLY

CUTTER DRIVE

BLADES

SUSPENSION & CASTER WHEELS

ANTI-SCALP

FEATURES

DECK COVERS LIFT ARMS WEIGHT

OPTIONAL

EQUIPMENT

CERTIFICATION

	FULL FLOTATION CUTTING UNITS
72" SIDE DISCHARGE	72" REAR DISCHARGE	GUARDIAN® 72" RECYCLER®
MODEL 30368	MODEL 30369	MODEL 30379

72" (183 cm) width of cut, three blade,	72" (183 cm) width of cut, three blade,	72" (183 cm) width of cut, three blade,
front mounted rotary. Adjustable front baffle.	front mounted rotary. Rear discharge.	front mounted rotary. Recycling with
Side discharge.		vertical discharge.

Mows up to 3.6 acres/h (1.46 hectares/h) at 5 mph (8 km/h).

Offset 7.1" (18 cm) to the left; 37.9 (96 cm)	Deck offset to the left from centerline:	Deck offset to left from centerline:
uncut circle left. Deck overhang: 19.7"	5.25" (13 cm). Deck trim width from outside	7" (18 cm). Deck trim width from outside
(50 cm) from outside of wheel to left trim side.	of standard traction tire to trim side - left:	of standard tire to trim side - left: 17.4"
Uncut circle with use of wheel brakes: 0"	17.4" (44 cm). Uncut circle with use of	(44 cm). Uncut circle with use of wheel
	wheel brakes: 0."	brakes: 0".

1-5" (2.5-12.7 cm) adjustable front and rear in .5" (12.7 mm) increments with spacers on		1.5-5" (3.8-12.7 cm)
the front caster shafts.

Welded 7-gauge steel, 5.5" (14 cm) deep.	7-gauge steel, 4.25" (11 cm) deep housing,	7-gauge steel, 4.25" (11 cm) deep housing,
5/16" (8 mm) rubber discharge chute.	welded construction.	welded construction.

Ductile cast iron spindle housing. Dual Timpken® greaseable tapered roller bearings. 1.25" (3.2 cm) diameter solid cold finished steel spindle shaft. Splined connection between spindle shaft and pulley. Welded blade retainer plus anti-scalp cups.

Isolation mounted PTO driven gearbox with 1.25:1 spiral bevel gears. “B” section belt to spindles. 1.25" (3.2 cm) diameter spindles mounted in two greaseable tapered roller bearings.

Three 24.5" (62 cm) long, .25"	Three 25.18" (64 cm) long, .25"	Three 25.18" (64 cm) long, .25"
(6 mm) thick, 2.5" (6 cm) wide heat-treated	(6 mm) thick, 2.5" (6 cm) wide heat-treated	(6 mm) thick, 2.5" (6 cm) wide heat-treated
steel blades. Optional Atomic™ Mulching	steel blades. Optional Atomic Mulching	steel blades. Optional Atomic Mulching
Blade.	Blade.	Blade.

Independent, 21/2" square tubing, lift/push arms each attached to separate castor arms.

Front: Two 8.0 x 3.5 pneumatic tires (foam filled optional) with tubes and maintenance free bearings. Tensioning caps made from GE XENOY 6230 impact modified thermoplastic alloy are used to hold the castor wheels on the castor arms.

Six anti-scalp rollers. Replaceable skid on	Five anti-scalp rollers. Anti-scalp cup	Anti-scalp cup located on each blade.
trim side. Anti-scalp cup located on	located on each blade.	Six anti-scalp rollers. Replaceable skids.
each blade.

Quick-release type latches; no tools required.

Independent lift arms and hydraulic weight transfer provide deck flotation.

530 lbs. (240 kg)	441 lbs. (200 kg)	491 lbs. (223 kg)

Rear Weight Kit, High Tip Speed Kit,	Guardian Recycler Conversiton Kit.	Rear Discharge Conversion Kit, Rear
Striping Kit, Leaf Mulcher Kit.		Weight Kit.

Cutting unit meets specification of American National Standard ANSI B71.4-2004, Safety Specifications for commercial turf care equipment. Cutting unit meets specifications of European standard EN836, CE approved.

*Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only. Actual products offered for sale may vary in design, required attachments and safety features. Consult your local Toro Distributor.

[1] Mowing rate is dependent on conditions.