Check for Loose Fasteners and Parts | Weed Eater 530163512, FL25

WARNING: Disconnect the spark plug before performing maintenance except for carburetor adjustments.

CHECK FOR LOOSE

FASTENERS AND PARTS

SSpark Plug Boot S Air Filter

S Housing Screws

S Assist Handle Screws S Debris Shield

CHECK FOR DAMAGED OR

WORN PARTS

Contact an authorized service dealer for re- placement of damaged or worn parts.

S ON/STOP Switch -- Ensure ON/STOP switch functions properly by pushing and releasing the switch. Make sure engine stops. Wait 5 seconds before attempting to restart unit to allow switch to reset. Restart engine and continue.

SFuel Tank -- Discontinue use of unit if fuel

tank shows signs of damage or leaks.

S Debris Shield -- Discontinue use of unit if debris shield is damaged.

INSPECT AND CLEAN UNIT AND LABELS

S After each use, inspect complete unit for loose or damaged parts. Clean the unit and labels using a damp cloth with a mild deter- gent.

SWipe off unit with a clean dry cloth.

CLEAN AIR FILTER

A dirty air filter decreases engine perform- ance and increases fuel consumption and

harmful emissions. Always clean after every 5 hours of operation.

1. Clean the cover and the area around it to keep dirt from falling into the carburetor chamber when the cover is removed.

2. Remove parts as illustrated.

NOTE: To avoid creating a fire hazard or producing harmful evaporative emissions, do not clean filter in gasoline or other flammable solvent.

3.Wash the filter in soap and water.

4.Allow filter to dry.

5.Add a few drops of oil to the filter; squeeze the filter to distribute oil.

6.Replace parts.

Air Filter

Screws

Air Filter Cover

REPLACE SPARK PLUG

Replace the spark plug each year to ensure the engine starts easier and runs better. Set spark plug gap at 0.025 inch. Ignition timing is fixed and nonadjustable.

1.Twist, then pull off spark plug boot.

2.Remove spark plug from cylinder and dis- card.

3.Replace with Champion RCJ-6Y spark plug and tighten securely with a 3/4 inch socket wrench.

4.Reinstall the spark plug boot.

LINE REPLACEMENT

1.Remove spool by firmly pulling on tap button.

2.Clean entire surface of hub and spool.

3.Replace with a pre-wound spool, or cut two lengths of 12-1/2feet of 0.080! (2 mm) di- ameter Weed Eaterr brand line.

WARNING: Never use wire, rope, string, etc., which can break off and become a dangerous missile.

4.Insert ends of the lines about 1/2 inch (1 cm) into the small holes on the inside of spool.

Spool

Small

Holes

Line exit holes					Line in Notch

Line in Notch

Hub

5.Wind the line evenly and tightly onto the spool. Wind in the direction of the arrows found on the spool.

6.Push the lines into the notches, leaving 3 to 5 inches (7 -- 12 cm) unwound.

7.Insert the lines into the the exit holes in the hub as shown in the illustration.

8.Align the notches with the line exit holes.

9.Push spool into hub until it snaps into place.

10.Pull the lines extending outside of the hub to release the lines from the notches.

530163512, FL25 specifications

The Weed Eater 530163512 FL25 is a versatile and robust string trimmer designed for both casual gardeners and experienced landscapers. This model is well-regarded for its blend of power, efficiency, and user-friendly features that make yard maintenance a breeze.

One of the standout features of the FL25 is its 25cc, 2-cycle engine. This engine is engineered to deliver sufficient power for tackling tough weeds and grass while maintaining a compact size. The powerful motor not only aids in efficient trimming but also ensures that users can handle larger areas with less effort. The engine is designed for easy starting, reducing the frustration often associated with small engine equipment.

The FL25 boasts a dual-line trimmer head, which allows for a wider cutting path compared to single-line models. This feature enhances productivity by trimming more grass in a single pass. The trimmer head is also equipped with an automatic bump feed system, enabling users to advance the line without stopping the engine. This convenience means less downtime and a smoother trimming experience.

Another notable characteristic of the Weed Eater 530163512 is its lightweight construction. Weighing in at just under 10 pounds, it is designed for ease of maneuverability without sacrificing durability. The comfortable, cushioned grip handle helps reduce vibration, allowing for extended use without causing hand fatigue.

The FL25 is engineered with a split shaft design, which allows for easy storage and transport. This feature also enables users to attach various accessories, making this trimmer a versatile tool in any gardener's arsenal.

In terms of technologies, the Weed Eater FL25 incorporates a low-emission engine, which contributes to a cleaner environment by minimizing harmful exhaust output. This aligns with modern standards for environmental responsibility and user health.

Overall, the Weed Eater 530163512 FL25 stands out as a reliable, efficient, and convenient string trimmer. Its combination of a powerful engine, dual-line capability, and ergonomic design makes it a top choice for anyone looking to maintain a well-kept yard. Whether tackling overgrown grasses or edging along pathways, the FL25 is engineered to deliver excellent results every time.