Weed Eater 545186796 Starting a Warm Engine, Starting a Flooded Engine, Operating Position

Page 8

gine doesn’t start after 6 pulls (at the HALF CHOKE position), move the choke lever to the FULL CHOKE position and press the primer bulb 6 times. Squeeze and hold the throttle trigger and pull the starter rope 2 more times. Move the choke lever to the HALF CHOKE position and pull the starter rope until the engine runs, but no more than 6 pulls. If the engine still doesn’t start, it is probably flooded. Proceed to STARTING A FLOODED ENGINE.

8.Once the engine starts, allow it to run 10 se- conds, then move the choke lever to the RUN position. Allow the unit to run for 30 more seconds at RUN before releasing the throttle trigger. NOTE: If engine dies with the choke lever in the RUN position, move the choke lever to the HALF CHOKE position and pull the rope until engine runs, but no more than 6 pulls.

STARTING A WARM ENGINE

1.Move the choke lever to the HALF CHOKE position.

2.Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until the en- gine runs smoothly.

3.Pull starter rope sharply until engine runs, but no more than 6 pulls.

4.Allow engine to run 15 seconds, then move the choke lever to RUN.

NOTE: If engine has not started, pull starter rope 5 more pulls. If engine still does not run, it is probably flooded.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the choke lever in the RUN position; then, pull the rope to clear the engine of excess fuel. This could require pulling the starter handle many times depending on how badly the unit is flooded. If the unit still doesn’t start, refer to TROUBLESHOOTING TABLE or call 1-800-554-6723.

OPERATING INSTRUCTIONS

It is recommended that the engine not be operated for longer than 1 minute at full throttle.

OPERATING POSITION

ALWAYS

WEAR:

Eye protection

Long

Pants

Heavy

Shoes

Cut from your right to your left.

WARNING: Always wear hearing protection and eye protection. Never lean over the trimmer head. Rocks or debris can ricochet or be thrown into eyes and face and cause blindness or other serious injury.

Do not run the engine at a higher speed than necessary. The cutting line will cut efficiently when the engine is run at less than full throttle. At lower speeds, there is less engine noise and vibration. The cutting line will last longer and will be less likely to “weld” onto the spool.

Always release the throttle trigger and allow the engine to return to idle speed when not cutting. To stop engine:

SRelease the throttle trigger.

S Push and hold the STOP switch in the STOP position until the engine stops.

TRIMMER LINE ADVANCE

The trimmer line will advance approximately 2 inches (5 cm) each time the bottom of the trimmer head is tapped on the ground with the engine running at full throttle.

The most efficient line length is the maximum length allowed by the line limiter.Always keep the shield in place when the tool is being oper- ated.

To advance line:

SOperate the engine at full throttle.

SHold the trimmer head parallel to and above

the grassy area.

STap the bottom of the trimmer head lightly on the ground one time. Approximately 2

inches (5 cm) of line will be advanced with each tap.

Always tap the trimmer head on a grassy area. Tapping on surfaces such as concrete or asphalt can cause excessive wear to the trimmer head.

If the line is worn down to 2 inches (5 cm) or less, more than one tap will be required to ob- tain the most efficient line length.

WARNING: Use only 0.080 inch (2

mm)diameter line. Other sizes of line will not advance properly and will result in improper cutting head function or can cause serious injury. Do not use other materials such as wire, string, rope, etc. Wire can break off dur- ing cutting and become a dangerous missile that can cause serious injury.

CUTTING METHODS

WARNING: Use minimum speed and do not crowd the line when cutting around hard objects (rock, gravel, fence posts, etc.), which can damage the trimmer head, become entangled in the line, or be thrown causing a serious hazard.

SThe tip of the line does the cutting. You will achieve the best performance and mini- mum line wear by not crowding the line into the cutting area. The right and wrong ways are shown below.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Manual de Instrucciones Manuel d’Instructions Identification of Safety Symbols Safety Rules Operator SafetyUnit / Maintenance Safety Fuel SafetyCutting Safety Transporting and StorageAssembly Shaft AssemblyAdjusting the Handle Attaching ShieldStop Switch OperationKnow Your Trimmer Primer BulbHOW to Stop Your Unit HOW to Start Your UnitBefore Starting Engine Fueling Engine Fuel RequirementsStarting a Warm Engine Starting a Flooded EngineOperating Position Trimmer Line AdvanceMaintenance Inspect and Clean Unit and LabelsClean AIR Filter Check for Loose Fasteners and PartsService and Adjustments Line ReplacementMuffler and Spark ARREST- ING Screen Replace Spark PlugCarburetor Idle Speed Adjustment Seasonal StorageFuel System EngineTroubleshooting Table Cause Remedy Limited Warranty Canada, contactIntermediate 125 hours Extended 300 hours

FX26SC, 545186796 specifications

The Weed Eater FX26SC is a versatile and powerful string trimmer designed for homeowners and landscaping professionals who demand performance and reliability. With its 26cc engine, this trimmer delivers ample power to tackle even the toughest grass and weeds, making it an essential tool for maintaining a pristine yard or garden.

One of the standout features of the FX26SC is its ease of use. The trimmer is equipped with a lightweight design, which allows for extended use without causing fatigue. Its balanced weight distribution enhances maneuverability, making it easier to trim around flower beds, fences, and other obstacles in your yard. The ergonomic handle is designed for comfort, providing a secure grip that reduces strain on the hands during operation.

The FX26SC features a dual-line system that enables efficient cutting. This system allows for a wider cutting path, allowing users to finish jobs more quickly while achieving a clean, precise cut. The trimmer also features a bump feed head that automatically advances the line when you tap it on the ground, minimizing downtime and ensuring continuous operation.

In terms of technology, the FX26SC comes with a reliable 2-stroke engine that provides a strong power-to-weight ratio. This engine technology is designed for lower emissions, making it an environmentally friendly choice for users who want to minimize their ecological footprint. The trimmer also features an easy-start system, which reduces the effort needed to start the engine, allowing users to get straight to work without the hassle of cumbersome starting procedures.

Its durable construction ensures that the Weed Eater FX26SC can withstand the rigors of regular use. The frame is designed to resist wear and tear from tough outdoor conditions, prolonging the life of the trimmer. Maintenance is straightforward, with easily accessible parts that make it simple to perform routine checks and repairs.

Overall, the Weed Eater FX26SC is more than just a string trimmer; it's a reliable outdoor tool loaded with features and technologies that enhance performance, comfort, and efficiency. Whether you're a homeowner looking to keep your lawn in check or a professional landscaper needing a dependable tool, the FX26SC meets a variety of cutting needs with ease and precision.
Top Page Image Contents