Weed Eater 545186796, FX26SC Service and Adjustments, Muffler and Spark ARREST- ING Screen

Page 10

1. Clean the air filter cover and the area around it to keep dirt from falling into the carburetor chamber when the cover is opened.

2. Open air filter cover by pushing button (see illustration). Remove air filter.

NOTE: To avoid creating a fire hazard or producing harmful evaporative emissions, do not clean filter in gasoline or other flammable solvent.

3.Wash the filter in soap and water.

4.Allow filter to dry.

5.Replace air filter and close cover.

Button

Air Filter

Air Filter Cover

MUFFLER AND SPARK ARREST- ING SCREEN

WARNING: The muffler on this prod- uct contains chemicals known to the State of California to cause cancer.

As your unit is used, carbon deposits build up on the muffler and spark arresting screen. For normal homeowner use, however, the muffler and spark arresting screen will not re- quire any service.

After 50 hours of use, we recommend that your muffler be serviced or replaced by your authorized service dealer.

REPLACE SPARK PLUG

Replace the spark plug each year to ensure the engine starts easier and runs better. Set spark plug gap at 0.025 inch (0.6 mm). Igni- tion timing is fixed and nonadjustable.

1.Twist, then pull off spark plug boot.

2.Remove spark plug from cylinder and dis- card.

3.Replace with Champion RCJ-6Y spark plug and tighten securely with a 3/4 inch (19 mm) socket wrench.

4.Reinstall the spark plug boot.

SERVICE AND ADJUSTMENTS

LINE REPLACEMENT

1.Remove spool by firmly pulling on tap button.

2.Clean entire surface of hub and spool.

3.Replace with a pre-wound spool, or cut two lengths of 12-1/2 feet of 0.080 inch (2 mm) diameter WEED EATER brand line.

WARNING: Never use wire, rope, string, etc., which can break off and become a dangerous missile.

4.Insert ends of the lines about 1/2 inch (1 cm) into the small holes on the inside of spool.

Line in notch

Hub

Line exit hole

Line in notch

Line exit hole

Spool

Small Holes

5.Wind the line evenly and tightly onto the spool. Wind in the direction of the arrows found on the spool.

6.Push the lines into the notches, leaving 3 to 5 inches (7 -- 12 cm) unwound.

7.Insert the lines into the the exit holes in the hub as shown in the illustration.

8.Align the notches with the line exit holes.

9.Push spool into hub until it snaps into place.

10.Pull the lines extending outside of the hub to release the lines from the notches.

REPLACING THE TRIMMER HEAD

1.Hold the dust cup with a wrench to keep the shaft from turning while removing and installing trimmer head.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Manual de Instrucciones Manuel d’Instructions Identification of Safety Symbols Safety Rules Operator SafetyCutting Safety Unit / Maintenance SafetyFuel Safety Transporting and StorageAdjusting the Handle AssemblyShaft Assembly Attaching ShieldKnow Your Trimmer Stop SwitchOperation Primer BulbBefore Starting Engine Fueling Engine HOW to Stop Your UnitHOW to Start Your Unit Fuel RequirementsOperating Position Starting a Warm EngineStarting a Flooded Engine Trimmer Line AdvanceClean AIR Filter MaintenanceInspect and Clean Unit and Labels Check for Loose Fasteners and PartsMuffler and Spark ARREST- ING Screen Service and AdjustmentsLine Replacement Replace Spark PlugFuel System Carburetor Idle Speed AdjustmentSeasonal Storage EngineTroubleshooting Table Cause Remedy Limited Warranty Canada, contactIntermediate 125 hours Extended 300 hours

FX26SC, 545186796 specifications

The Weed Eater FX26SC is a versatile and powerful string trimmer designed for homeowners and landscaping professionals who demand performance and reliability. With its 26cc engine, this trimmer delivers ample power to tackle even the toughest grass and weeds, making it an essential tool for maintaining a pristine yard or garden.

One of the standout features of the FX26SC is its ease of use. The trimmer is equipped with a lightweight design, which allows for extended use without causing fatigue. Its balanced weight distribution enhances maneuverability, making it easier to trim around flower beds, fences, and other obstacles in your yard. The ergonomic handle is designed for comfort, providing a secure grip that reduces strain on the hands during operation.

The FX26SC features a dual-line system that enables efficient cutting. This system allows for a wider cutting path, allowing users to finish jobs more quickly while achieving a clean, precise cut. The trimmer also features a bump feed head that automatically advances the line when you tap it on the ground, minimizing downtime and ensuring continuous operation.

In terms of technology, the FX26SC comes with a reliable 2-stroke engine that provides a strong power-to-weight ratio. This engine technology is designed for lower emissions, making it an environmentally friendly choice for users who want to minimize their ecological footprint. The trimmer also features an easy-start system, which reduces the effort needed to start the engine, allowing users to get straight to work without the hassle of cumbersome starting procedures.

Its durable construction ensures that the Weed Eater FX26SC can withstand the rigors of regular use. The frame is designed to resist wear and tear from tough outdoor conditions, prolonging the life of the trimmer. Maintenance is straightforward, with easily accessible parts that make it simple to perform routine checks and repairs.

Overall, the Weed Eater FX26SC is more than just a string trimmer; it's a reliable outdoor tool loaded with features and technologies that enhance performance, comfort, and efficiency. Whether you're a homeowner looking to keep your lawn in check or a professional landscaper needing a dependable tool, the FX26SC meets a variety of cutting needs with ease and precision.
Top Page Image Contents