Weed Eater 545186761 Tube Assembly, Adjusting Assist Handle, Attaching Edge Guide and Shield

Page 4

ASSEMBLY

WARNING: If received assembled, review all assembly steps to ensure your unit is properly assembled and all fasteners are secure.

TUBE ASSEMBLY

Upper Locking Sleeve Assembly

Wires

Lower Locking Sleeve Assembly

1.Align upper tube groove with triangle on lower locking sleeve assembly. Push tubes together until they snap into place.

Upper Tube

Groove

Alignment Triangle

2.Try to pull tubes back apart. If the tubes do not come apart, they are properly snapped into place. If the tubes come apart, repeat step 1 and push until the tubes snap into place.

3.Slide upper locking sleeve assembly over lower locking sleeve assembly and tight- en by turning clockwise.

4.Ensure locking sleeve assembly and alignment decals appear as illustrated be- low.

Alignment decals

WARNING: Failure to completely en- close excess wires in upper tube during assem- bly of the unit may result in damage to the wires and/or the unit or serious injury to the operator including electrocution.

WARNING: The upper and lower tubes must be snapped together, remain per- manently assembled together and the locking sleeve assembly must be fully tightened be- fore and during use to avoid serious injury to the operator and/or damage to the unit. DO NOT attempt to disassemble unit after initial assembly.

ADJUSTING ASSIST HANDLE

1.Loosen and remove wing nut and bolt from assist handle.

2.Place unit on a flat surface.

3.Firmly push the assist handle over the tube. To make installation easier, tilt han- dle toward trigger housing while pushing down (see illustration).

4.Reinstall bolt in handle. Thread wing nut onto bolt.

5.Adjust the handle up or down the tube to a comfortable position; tighten wing nut se- curely.

Assist handle

Trigger housing

Tube

ATTACHING EDGE GUIDE AND SHIELD

WARNING: The shield must be prop- erly installed. The shield provides partial protec- tion to the operator and others from the risk of thrown objects. Your unit is equipped with a line limiter blade, which cuts excess line to the prop- er length while running. The line limiter blade (on underside of shield) is sharp and can cut you. NOTE: If shield is not properly installed, dam- age to unit (including motor failure) will result.

1.Insert edge guide into two holes in shield. NOTE: Edge guide must be positioned on shield prior to installation on motor housing (see following illustration).

Edge Guide

Front

Locking

Tab

Rear Locking

Tabs

Shield

2.Place shield over cutting head at an angle to the motor housing. Insert front locking tab on shield into opening in front of motor housing.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Advertencia AvertissementOperator Safety Safety RulesElectrical Safety Unit Safety Cutting SafetyMaintenance Safety Transporting and StorageAssembly Tube AssemblyAdjusting Assist Handle Attaching Edge Guide and ShieldOperation Operating Instructions Select AN Extension CordAttach the Extension Cord to Your Trimmer Correct Operating PositionMaintenance Service and AdjustmentsBefore Each USE After Each USEUser Replaceable Service Parts Installing Spool with LineRefilling the Spool with Line Electrical failure Troubleshooting TableIncorrect line size Canada, contact Husqvarna Outdoor Products IncWeed Eater

545186761 specifications

The Weed Eater 545186761 is a powerful and reliable outdoor tool designed for tackling overgrown lawns and gardens with ease. This string trimmer combines advanced technology with ergonomic design, making it an essential companion for homeowners and landscaping professionals alike.

One of the standout features of the Weed Eater 545186761 is its robust 25cc two-stroke engine. This engine delivers a commendable power-to-weight ratio, allowing users to efficiently cut through tough weeds and grasses. The lightweight design prevents user fatigue during extended use, making it easier to manage even the most challenging yard work.

The trimmer is equipped with a 17-inch cutting width, which ensures a wide swath of cutting in a single pass. This feature not only speeds up the trimming process but also enhances overall efficiency. The dual-line cutting system allows for precise cutting and reduces the need for frequent line replacements, ensuring uninterrupted workflow.

Comfort is a key consideration in the design of the Weed Eater 545186761. It features an adjustable handle that can be tailored to the user's preference, promoting better posture and reducing strain on the arms and back during operation. The soft-grip handle enhances user comfort, while the lightweight construction makes maneuverability a breeze.

The trimmer also incorporates a simple and effective line feeding system, which allows for easy reloading of the cutting line without the need for additional tools. This convenience is particularly beneficial for users who want to maintain their trimming routine without delays.

Another noteworthy characteristic of the Weed Eater 545186761 is its durability. Constructed with high-quality materials, the trimmer is designed to withstand harsh outdoor conditions, ensuring a long lifespan. The choke and primer system is also designed for easy starting, eliminating frustration and time wasted during setup.

In summary, the Weed Eater 545186761 is a versatile and efficient string trimmer that combines power, comfort, and durability. With its user-friendly features and advanced technologies, it is an excellent choice for anyone looking to maintain a tidy outdoor space with minimal effort. Whether you are a seasoned landscaper or a homeowner tackling weekend projects, this trimmer is sure to meet your needs and exceed expectations.
Top Page Image Contents