Assembly

SHave all service and maintenance not ex- plained in this manual performed by an autho-

rized service dealer to avoid creating a haz- ard.

SNever douse or squirt the unit with water or any other liquid. Clean unit and labels with a damp sponge. Keep handles dry, clean, and

free from oil and grease.

SKeep the air vents clean and free of debris to avoid overheating the motor. Clean after each use.

TRANSPORTING AND STORAGE

SStop the unit and place in wall bracket for

storage and battery charging.

SCarry the unit with motor stopped.

SStore unit indoors in a high, dry place out of

the reach of children.

SDo not hang unit so that the trigger switch is depressed.

BATTERY CARE

SIf over a period of time the battery quickly

runs down after a full 24 hour charging peri- od, a replacement battery is needed.

SThere will be some charge present in the bat- tery, but to ensure maximum running time, re-

charge your battery for 24 hours before use. S Permanent connection to the charger in a well--ventilated area will automatically keep your battery fully charged and ready for use.

STo prevent permanent battery damage, never store in a discharged condition.

SBattery Sealed for Life

No maintenance required

SBattery replacement

Should your battery need to be replaced, contact your authorized service dealer for a replacement battery and for proper dispos- al of the old battery.

WINTER STORAGE

SFully charge for 24 hours before winter stor-

age.

S If you are unable to leave your cordless trimmer on permanent charge, recharge the battery every 3 to 4 months for a full 24 hour charging period to fully charge the bat- tery during winter storage.

SAvoid extended storage without recharge. S Store in a cool dry place.

IMPORTANT!

DISPOSE OF YOUR OLD BATTERIES SAFELY. TAKE THE COMPLETE UNIT TO YOUR AUTHORIZED SERVICE DEALER. DO NOT CUT OPEN, BURN OR INCINERATE.

SAVE THESE INSTRUCTIONS

WARNING: If received assembled, review all assembly steps to ensure your unit is properly assembled and all fasteners are secure.

SHAFT ASSEMBLY

WARNING: Ensure that the excess wire between the switch handle and motor housing is not twisted and is enclosed in switch handle and motor housing during assembly of the unit. Failure to do so may result in damage to the wires and/or the unit or serious injury to the operator.

1.Push the tube into the switch handle until it snaps into place.

Switch Handle

Tube

2.Push the tube into the motor housing until it snaps into place.

Tube

Motor Housing

3.Try to remove tube from switch handle and motor housing. If the tube remains in place, it is properly snapped into place. If the tube will not remain in place, repeat steps 1 and 2. Push until the tube snaps into place.

ATTACHING THE SHIELD

WARNING: The shield must be prop- erly installed. The shield provides partial protec- tion from the risk of thrown objects to the opera- tor and others. Your unit is equipped with a line limiter pin, which cuts excess line to the proper length while running.

NOTE: If shield is not properly installed, dam- age to unit (including motor failure) will result.

1.Place the shield onto the motor housing. Ensure the cutting head remains free to rotate and the line is not caught between the shield and the motor housing (see il- lustration).

545186757 specifications

The Weed Eater 545186757 is a robust and reliable solution for homeowners and landscaping professionals looking to maintain their lawns and gardens. Known for its powerful performance and user-friendly design, this weed eater is equipped with a range of features and technologies designed to enhance efficiency and ease of use.

One of the standout features of the Weed Eater 545186757 is its lightweight construction, making it easy to maneuver even in tight spaces. Weighing in at just under eight pounds, it minimizes fatigue during extended use, allowing users to tackle larger areas without discomfort. This is particularly beneficial for those who may face physical limitations or simply prefer a lighter tool for their gardening tasks.

Equipped with a reliable 2-stroke engine, this weed eater provides superior performance, delivering consistent power to tackle tough weeds and overgrown grass. The engine is designed for easy starting, with a simple pull-to-start mechanism that eliminates the frustration often encountered with other models. This ensures that users can get to work quickly without spending precious time wrestling with machinery.

In addition to its powerful engine, the Weed Eater 545186757 features a bump head line feed system that simplifies the process of replacing trimming line. With a simple bump of the head against the ground, users can release more line without needing to stop and manually feed it, significantly increasing productivity. The dual line design further enhances cutting efficiency, allowing for a wider cutting swath, enabling users to finish their tasks faster.

The ergonomic design of the handle is another key characteristic of the Weed Eater 545186757. The padded grip ensures comfort during use, while the adjustable control handle allows users to customize their grip for better control and precision. This adjustability is particularly useful for users of varying heights and preferences, promoting a more enjoyable and effective experience.

Finally, the Weed Eater 545186757 is built for durability. Constructed with high-quality materials, it is designed to withstand the rigors of outdoor use. Whether you are maintaining a small garden or managing a larger property, this weed eater is up to the challenge, proving to be a valuable addition to any homeowner's toolkit. With its combination of power, versatility, and user-centric design, the Weed Eater 545186757 stands out as a go-to choice for effective lawn care.