To Charge Your Unit, Recharging Your Unit

SCharge continuously when not in use. Con- tinuous charging will not damage the bat- tery. The charger will automatically keep the battery charged and ready for use dur-

ing storage.

S During charging, the charger becomes warm. This is normal and means the char- ger is operating correctly.

TO CHARGE YOUR UNIT:

1.Place the trimmer in the wall bracket.

2.Plug the charger into a standard house- hold electrical outlet.

3.When properly connected, the red charge indicator light (LED) will glow.

NOTE: The red charge indicator light (LED) on the charger glows continuously during charging.

4.The battery will be fully charged in 24 hours.

RECHARGING YOUR UNIT

SRecharge the battery as soon as the cutting

power of your cordless trimmer is no longer effective.

S Avoid running the battery into full dis- charge, i.e. avoid draining the battery com- pletely.

S Follow the procedure outlined in the CHARGING YOUR UNIT section.

SRecharging the battery according to these instructions should ensure maximum bat-

tery life.

SDo not recharge the battery in an area of ex- treme heat or cold. It will work best at nor- mal room temperature.

CORRECT OPERATING POSITION

TrimmingEdging

WARNING: Always wear eye protec- tion. Never lean over the trimmer head. Rocks or debris can ricochet or be thrown into eyes and face and cause blindness or other serious injury.

When operating unit, stand as shown and check for the following:

SWear eye protection and heavy clothing.

SHold trigger handle with right hand and as- sist handle with left hand.

SKeep unit below waist level.

SCut only from your right to your left to en- sure debris is thrown away from you. With- out bending over, keep line near and paral- lel to the ground and not crowded into material being cut.

AUTOMATIC LINE FEED SYSTEM

When the trimmer is initially started, a small length of cutting line is fed out.

Line Limiter Pin

After approximately 5 seconds, the line will be cut to the correct length by the line limiter pin as the motor reaches full speed. Make sure

the motor is up to full speed before trim- ming. If the noise of the cutting line being cut

cannot be heard, more line will need to be fed out.

To feed more line:

SAllow the motor to stop completely; then, re- start the motor and allow it to reach full

speed.

SRepeat until you hear the line hitting against the line limiter pin (do not repeat this proce-

dure more than 6 times).

If problems are experienced with the auto- matic line feed, refer to the TROUBLE-

SHOOTING TABLE.

To manually feed the nylon line:

SIf required, the cutting line can be fed out manually.

STo operate, press and release manual line feed button while gently pulling on one of the line until it reaches the line limiter pin.

Manual Line

Feed Button

SIf the line extends past the line limiter pin, too much line has been fed out. If too much line is fed out, remove the spool cap and click spool counterclockwise until the line is at the desired length.

545186757 specifications

The Weed Eater 545186757 is a robust and reliable solution for homeowners and landscaping professionals looking to maintain their lawns and gardens. Known for its powerful performance and user-friendly design, this weed eater is equipped with a range of features and technologies designed to enhance efficiency and ease of use.

One of the standout features of the Weed Eater 545186757 is its lightweight construction, making it easy to maneuver even in tight spaces. Weighing in at just under eight pounds, it minimizes fatigue during extended use, allowing users to tackle larger areas without discomfort. This is particularly beneficial for those who may face physical limitations or simply prefer a lighter tool for their gardening tasks.

Equipped with a reliable 2-stroke engine, this weed eater provides superior performance, delivering consistent power to tackle tough weeds and overgrown grass. The engine is designed for easy starting, with a simple pull-to-start mechanism that eliminates the frustration often encountered with other models. This ensures that users can get to work quickly without spending precious time wrestling with machinery.

In addition to its powerful engine, the Weed Eater 545186757 features a bump head line feed system that simplifies the process of replacing trimming line. With a simple bump of the head against the ground, users can release more line without needing to stop and manually feed it, significantly increasing productivity. The dual line design further enhances cutting efficiency, allowing for a wider cutting swath, enabling users to finish their tasks faster.

The ergonomic design of the handle is another key characteristic of the Weed Eater 545186757. The padded grip ensures comfort during use, while the adjustable control handle allows users to customize their grip for better control and precision. This adjustability is particularly useful for users of varying heights and preferences, promoting a more enjoyable and effective experience.

Finally, the Weed Eater 545186757 is built for durability. Constructed with high-quality materials, it is designed to withstand the rigors of outdoor use. Whether you are maintaining a small garden or managing a larger property, this weed eater is up to the challenge, proving to be a valuable addition to any homeowner's toolkit. With its combination of power, versatility, and user-centric design, the Weed Eater 545186757 stands out as a go-to choice for effective lawn care.