Service and Adjustments, Replacing the Line

SERVICE AND ADJUSTMENTS

REPLACING THE LINE

1.Remove spool by firmly pulling on tap button.

2.Clean entire surface of hub and spool.

3.Replace with a pre-wound spool, or cut two lengths of 12-1/2 feet of 0.080″ (2 mm) dia- meter Weed Eaterr brand line.

WARNING: Never use wire, rope, string, etc., which can break off and become a dangerous missile.

4.Insert ends of the lines about 1/2 inch (1 cm) into the small holes on the inside of spool.

Spool

Small

Holes

Line exit holes

Line in Notch

Hub

5.Wind the line evenly and tightly onto the spool. Wind in the direction of the arrows found on the spool.

6.Push the lines into the notches, leaving 3 to 5 inches (7 -- 12 cm) unwound.

7.Insert the lines into the the exit holes in the hub as shown in the illustration.

8.Align the notches with the line exit holes.

9.Push spool into hub until it snaps into place.

10.Pull the lines extending outside of the hub to release the lines from the notches.

BLADE REPLACEMENT

Refer to the ASSEMBLY section for blade re- placement instructions and illustrations.

CARBURETOR ADJUSTMENT

WARNING: Keep others away when making idle speed adjustments. The trimmer head or blade will be spinning during most of this procedure. Wear your protective equip- ment and observe all safety precautions. Af- ter making adjustments, the trimmer head or blade must not move/spin at idle speed.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

S Engine will not idle when the throttle is released.

SThe trimmer head or blade moves/spins at idle.

Make adjustments with the unit supported so the cutting attachment is off the ground and will not make contact with any object. Hold the unit by hand while running and making ad- justments. Keep all parts of your body away from the cutting attachment and muffler.

Idle Speed Adjustment

Allow engine to idle. Adjust speed until engine runs without trimmer head or blade moving or spinning (idle too fast) or stalling (idle speed too slow).

S Turn idle speed screw clockwise to increase engine speed if engine stalls or dies.

STurn idle speed screw counterclockwise to decrease engine speed if trimmer head or blade moves or spins at idle.

WARNING: Recheck the idle speed after each adjustment. The trimmer head or blade must not move or spin at idle speed to avoid serious injury to the operator or others.

Idle Speed

Screw

Air Filter

Cover

If you require further assistance or are unsure about performing this procedure, contact an

authorized			service dealer or call
1--	800--	554--	6723.

STORAGE

WARNING: Perform the following steps after each use:

SAllow engine to cool before storing or trans- porting.

SStore unit and fuel in a well ventilated area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

SStore unit with all guards in place. Position unit so that any sharp object cannot acci-

dentally cause injury.

SStore unit and fuel well out of the reach of children.

SEASONAL STORAGE

Prepare unit for storage at end of season or if it will not be used for 30 days or more.

530164314 specifications

The Weed Eater 530164314 is a powerful and reliable string trimmer designed to make yard maintenance easier and more efficient. Engineered for both residential and light commercial use, this model stands out due to its combination of innovative features, user-friendly design, and robust performance.

One of the main features of the Weed Eater 530164314 is its lightweight and ergonomic design, which allows for comfortable handling during extended use. Weighing in at a manageable level, users can easily maneuver around shrubs, flower beds, and other landscaping obstacles without experiencing undue fatigue. The adjustable handle further enhances comfort, allowing users of different heights to maintain a natural grip while working.

The trimmer is equipped with a powerful engine that delivers impressive cutting power. This engine allows the Weed Eater to tackle dense grass, weeds, and overgrown vegetation with ease. Not only does it provide efficiency, but it also ensures that users can complete their tasks in a timely manner, ultimately saving both time and effort.

Another key characteristic of the Weed Eater 530164314 is its innovative dual-line cutting system. This feature allows for a wider cutting path than traditional single-line models, significantly increasing trimming efficiency. As the trimmer rotates, the two lines efficiently slice through grass and weeds, providing a clean and thorough cut while minimizing the need for multiple passes.

The automatic feed spool is another vital technology integrated into this trimmer. This system automatically feeds the cutting line as needed, eliminating the hassle of stopping work to manually adjust the line. Users can work continuously and focus on the task at hand, resulting in increased productivity.

Durability is also a highlight of the Weed Eater 530164314, with a sturdy construction designed to withstand the rigors of outdoor use. The robust materials used in its construction ensure that it remains functional and reliable over time, making it a worthwhile investment for homeowners and landscape professionals alike.

In conclusion, the Weed Eater 530164314 is a string trimmer that excels in design, performance, and ease of use. Its lightweight build, powerful engine, dual-line cutting system, automatic feed spool, and durable construction make it a top choice for anyone seeking an efficient and effective solution for maintaining their outdoor spaces. Whether you’re tackling a small garden or a larger lot, the Weed Eater 530164314 is equipped to handle various landscaping challenges.