Craftsman 557-5199, 833.14334 owner manual Searselectronicinsect Killer Model no, 31 557

SEARSELECTRONICINSECT KILLER - MODEL NO. 833.14334

REF. NO.	PART NO.			DESCRIPTION	QTY.
1	554	722	HANGING	RING	1
2	596	1565 P02	THREADED	NIPPLE, 1" LONG	1
3	567	420	NEOPRENE	WASHER	1
4	596	784	REDUCING	BUSHING	1
5	555	5314 SR	HOOD		I

6245 6260 P27 THREAD CUTTING SCREW, F, 8-32 x 3/8 4

7	596	785		LOCKNUT			1
8	544	5288		GRID SPACER			5
9	544	3750		SPACER INSULATOR			2
10	245	6245	P28	SHEET METAL		SCREW_ NO. 8 x 1/2	9
11	532	30O6		BALLAST			2
12	576	4890		TRANSFORMER			1
13	505	3370		BULB SOCKET		ASSY	2
14	552 3369		P03	REFLECTOR			2
15	555 3534			BULB RETAINER			1
16	512 392 P26			BULB BOOT WIRE, 26';LONG			2
17	552 5202			TOP PLATE			1
18	531 2034			STARTER			2
19	512 5140			POWER CORD			1
20	571 5170			STARTER SOCKET			2
21	245 6236		Pll	SHEET METAL		SCREW, NO. 6 x 3/8	3
22	544 3749			MOUNTING	INSULATOR		3
23	245 6245		P12	SHEET METAL		SCREW, NO. 6 x 1/2	3
24	512 404 P02			HV GRID WIRE			2
25	530 2815		S	BULB, BLACK		LIGHT	2
26	553 2846		P01	INNER GRID			1
27	553 2847		P01	OUTER GRID			1
28	505 3377			BASKET ASSY			1
29	5O54031			PHOTOCELL	ASSY		1

30245 6260 P25 THREAD CUTTING SCREW, F, 8-32 x 1/4 2

31 557 5199 OWNER'SMANUAL 1

5

26

				15
	TROUBLESHOOTING	AND REPAIR	ANALYSIS
PROBLEM	POSSIBLE CAUSE			CORRECTION
A. Bulbs do not light	I. No electrical power.	1.	Check	fuse or circuit breaker.
and no high voltage		2.	Check	extension cord, (If used,)

on grid.

B. Bulbs light but no

grid high voltage.

C. Grid voltage present but bulbs do not

light.

O. Intermittent or

continuous sparking

between grids.

1. Shorted grids.

1, Lamp(s) not seated properly.

2.Starter defective.

3.Burned-out bulb(s).

1.Gap between grids is too small.

2.Grid clogged with foreign material.

3.Grid not seated in insulaitor.

1.Examine grids to see if inner and outer grids are free from foreign material, dirt or a build-up of dead insects.

2.Check to make sure inner grid _nd outer grid

are not touching. Use insulated screwdriver.

1.Check all sockets for proper seating and

alignment.	,,
2. Replace if needed.	,'

3.Replace if needed.

1.Unplug unit and adjust grids by bending

back into alignment using screwdriver blade.

2.Clean grid using an air blower.

3.Look for proper grid seating at all insulators,

Any problems you encounter that are not corrected by the action recommended in this chart should be referred to your nearest Sears Service Center.