Craftsman 917-371813 manual Engine Speed, Engine Zone Control, Drive Control Adjustment

Page 8

The operation of any lawn mower can result in foreign

objectsthrowninto theeyes, which can result in severe

eye damage, Always wear safety glasses or eye shields while oper- ating your lawn mower or performing any adjustmentsor repairs, We recommend a standardsafetyglassesorwidevisionsafety maskworn over spectacles,

HOW TO USE YOUR LAWN MOWER

ENGINE SPEED

Engine speed was set at the factory for

optimum performance, It is not adjustable,

ENGINE ZONE CONTROL

_I, CAUTION: Federal regulations require an engine control to be installed on this lawn mower in order to minimize the risk of blade contact injury, Do not under

any circumstances attempt to defeat the function of the operator control, The blade turns when the engine is running,

•Your lawn mower is equipped with an operator presence control bar which

requires the operator to be positioned behind the lawn mower handle to start

and operate the lawn mower,

DRIVE CONTROL

• Self-propelling

is controlled

by hold-

ing the operator

presence

control bar

down to the handle and pulling the drive

control lever rearward to the handle.

The farther toward the handle the lever

is pulled, the faster the unit will travel.

• Forward motion will stop when either

the operator presence

control bar or

DRIVE CONTROL ADJUSTMENT

Over time, the drive control system may be-

come "loose", resulting in decreased speed, There is a turnbuckle on the underside of the

drive control housing to increase tension on the drive cable, Proceed as follows:

1, Turn unit off and disconnect spark plug wire from spark plug,

2, Turn nut on underside of drive control to increase drive speed,

3, Operate mower to test drive speed, Readjust as required,

4, If condition fails to improve after the above steps (forward speed remains the same), your drive belt is worn and should be replaced,

Adjustment turnbuckle

TO ADJUST CUTTING HEIGHT

Both front wheels are adjusted by a single lever on the left front wheel, Likewise, both rear wheels are adjusted by a single lever on the left rear wheel,

•Pull adjuster lever toward wheel, To raise mower, move lever forward to

desired position, To lower mower, move the lever backward to desired position,

Be sure to adjust both front and rear

wheels to the same height,Height uster

drive control lever are released.

To stop

forward motion without stopping engine,

release only the drive control lever. Hold operator presence control bar down against handle to continue mowing without self-propelling,

TO LOWER MOWER LEVER BACKWARD

lever

NOTE: If after releasing the drive control the mower will not roll backwards, push the mower forward slightly to disengage drive wheels,

•To keep drive control engaged when

turning corners, push down on the handle to lift the front wheels off the

ground while turning lawn mower,

Operator presence control bar Drive control lever

TO

ENGAGEDRIVE

DRIVECONTROL

CONTROLDISENGAGED

LEVER FORWARD

TO RAISE MOWER

TO CONVERT MOWER

Your lawn mower was shipped ready to be used as a mulcher, To convert to rear

bagging or side discharging:

REAR BAGGING

•Remove knob securing mulcher door to lawn mower housing.

•Open mulcher door and insert tabs of discharge chute into hinge bracket

opening and position rear of chute over threaded stud.

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Craftsman Year Full Warranty on Craftsman Lawn Mower Do not Gasoline Capacity / Type Repair Protection Agreements To Install Attachments To Remove Lawn Mower from CartonLift Mowing PositionMeets Cpsc Safety Requirements Know Your Lawn MowerDrive Control Adjustment To Adjust Cutting HeightEngine Speed Engine Zone ControlFor Side Discharging Side DischargingFor Rear Bagging To Stop Engine OpenADD Gasoline Mowing TipsLubrication General RecommendationsBefore Each USE Lawn Mower Gear CaseAIR Filter To Clean AIR FilterTo Change Engine OIL Spark Plug Clean Under Drive CoverMuffler Lawn Mower To Adjust Cutting Height Rear DeflectorTo Remove Drive Belt PivotTo Adjust Handle To Replace Drive BeltEngine CarburetorHandle Engine Fuel SystemCylinder OFFProblem Raise Cutting HeightSears, Roebuck and Co., Hoffman Estates, IL No Hacer OperacionHacer API SG-SL SAE NGK BPR6ESMantenimiento DE LA Segadora Rendimiento DE LA SegadoraPara Remover LA Segadora DE LA Caja DE Carton Para Instalar LOS AccesoriosFamiliaricese CON SU Segadora Cumple CON LOS Requisitos DE Seguridad DE LA CpscComo Usar SU Segadora Velocidad DEL Motor Control DE LA ImpulsionAjuste DEL Mando Levantar EL CortaoespedPara Descarga Lateral Segadoras CON Descarga LateralCuando Convierta SU Segadora Importante Agregue GasolinaAntes DE Hacer Arrancar EL MotorPara Parar EL Motor ApagadoUSO USO Horas Temporada Horas Namiento Antes DE Cada USOLubricacion Tabla DE LubricacionSegadora LlantasRuedas DE Impulsion Cuidado DE LA CuchillaPara Limpiar EL Filtro DE Aire LubricacionFiltro DE Aire Limpieza Limpie Debajo DE LA Cubierta DE LA ImpulsionSegadora Para Ajustar LA Altura DE Corte Desviador TraseroParacambiarlacorreadeimpulsion Para Ajustar EL MangoMango ParaSegar HaciaProblema Mal corte Disparejo CausaCraftsman Rotary Lawn Mower - Model Number GCV160-LAS3A SAE 30WPage Axle Gear Case Assembly - Part Number KEY PartService Notes Honda 4=CYCLE Engine Model Number GCV160-LAS3A Label Choke Carburetor KEY Part NO. NO. Description Choke KEY Part NO. NO. DescriptionCamshaft Pulley KEY Part NO. NO. Description Honda 4-CYCLE Engine Model Number GCV160-LAS3A Flywheel KEY Part NO. NO. DescriptionRecoil Starter KEY Part NO. NO. Description Muffler Piston / Connecting ROD KEY Part NO. NO. Description Crankshaft KEY Part NO. NO. DescriptionNeed More HELP?
Top Page Image Contents