Craftsman 917.37248 owner manual Lawn Mower, To Adjust Cutting Height, Discharge Guard

Page 15

SERVICE AND ADJUSTMENTS

CAUT_©N: BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:

Release control bat.

oMake sure the blade and all moving parts have completely stopped.

,Disconnect spark plug wire from spark plug and place where it cannot come in contact with plug,

LAWN MOWER

TO ADJUST CUTTING HEIGHT

See "TO ADJUST CUTTING HEIGHT" in the Operation section of this manual.

DISCHARGE GUARD

The discharge guard, attached to the discharge opening of your lawn mower, is provided to prevent the possibility of injury resulting from objects being thrown out of the dis- charge opening into the operator mowing position. If the discharge guard becomes damaged, it should be replaced.

TO REMOVE/REPLACE DRIVE BELT

(See Fig. 16)

Remove drive cover. Remove bett by pushing down on gear case putley.

Turn tawn mower on its side with carburetor and fuel

cap up.

,Remove blade.

Remove debris shield.

Remove belt from engine pulley on crankshaft. o Install new belt by reversing above steps,

,Always use factory approved belt to assure fit and long life.

TO ADJUST DRRVE CONTROL CABLE

(See Fig. 17')

A drive control cable that needs adjustment will keep your lawn mower from self-propelling properly and can also cause gear case components to wear out sooner.

Remove drive cover.

,Loosen cable clamp screw "A" and nuts "B" and "C".

Hold down operator presence control bar to handle and engage drive control.

oMove shifter arm to drive position while rotating front wheels to be sure jaw clutch is engaged. Pull threaded sleeve with p_iers. Do not pull on control cable.

Tighten nut "C" until steeve is snug.

o Tighten screw"A" and nut"B".

,Push lawn mower back and forth to be sure gear case is engagedl

Replace drive cover.

o Release operator presence control bar.

PRESS _

FiG, !6

JAMNUT"C"-_PUER$

JAM NUT "B". "_%_.SLEEVE_

o.,vo

SHiFteR _._)

_

J Ill

AR

 

 

CLUTCH

 

ADJUSTING

SPRING

SCREW "A"

BRACKET

FJGo17

REAR DEFLECTOR

The rear deflector, attached between the rear wheels of

your lawn mower, is provided to minimize the possibility that objects will be thrown out the rear of the lawn mower into the operator's mowing position.

If the rear deflector becomes damaged, it should be replaced.

15

Image 15
Contents Sears Operation Maintenance AndstorageTraining PreparationProduct Specifications Limited TWO Year Warranty on Craftsman Power MowerIndex Engine Lawn Mower PerformanceRear BAG Optional Lowerhandle Catcherframe HOW to SET UP Your LawnTo Remove Lawn Mower from Carton MowerKnow Your Lawn Mower OperationEngine Zone Control HOW to USE Your Lawn MowerTo Install Grass Catcher See Fig Engine Speed See FigOperatorpresence Controlbar Drivecontr To Adjust Cutting Height See FigPour OIL SLOWLY. do not Over Fill To Start EngineMowing Tips OP AtionBefore Each USE Maintenance ScheduleGeneral Recommendations AS YOU CompleteLawn Mower Spark Plug CleaningClean Under Drive Cover AIR FilterDischarge Guard To Adjust Cutting HeightTo Adjust Drrve Control Cable Lawn MowerTo Adjust Handle See Figs, 18 Thru Engine SpeedCarburetor Engine OiL OtherHandle See Fig Fuel System0RAFTSMAN 22 Rotary Lawn Mower Model Number Repair PartsKEY Part Description Craftsman 22 Rotary Lawn Mower Model NumberRaftsman 22 Rotarylawn Mower Model Number Description KEY PartGear Case Assembly Part Number KEY Part KEYPart Description Craftsman 4-CYCLE Engine REF Part NO. no Description REF Part NO, noRewind Starter no REF Part NO. noREF Part Service Notes Cause Correction Troubleshooting PointsEngine Craftsman Model no Part Number Part Description Iiii