Afid Sea in carburetor may result if | Craftsman 917.270711 specification

Craftsman 917.270711 Afid Sea in carburetor may result if, To Adjust Carburetor, Final Setting

TOADJUST .'II'IROTTLECONTROL

CABLE --.

The tl_o_ttle _controlhas been preset at the factory and adjustment should not be nec- essary. Check adjustment as descn'bed below before loosening cable, if adjust- ment is necessary, proceed as follows:

•With engine not running, move throttle

-control lever from slow to cho!_e posi-

1ion. Slowly move lever from'choke to

astpos, .

•Check that holes "A" in governor control lever and hole in govemor plate line-up. ff _oles_A " are not aligned, loosen clamp screw and move throttle cable until holes are alii)ned. Tighten clamp screw securely.

___Go_vemor.... Governor

Control Lever Control Plate

	Clamp		Throttle
Holes "A"	Screw	:	Cable

TO ADJUST CARBURETOR

NOTE: The carburetor on this engine is low emission. It is equipped with an idle fuel adjusting needle)with a limiter cap, which allows some adjustment within the limits allowed by the cap. Do not attempt to remove the limiter cap. The limiter cap cannot be removed without breaking the adjusting needle.

_l'he carburetor has been'preset at the fac- tory and adjustment should not be neces- sary. However, minor adj;_rstment may be required to compensate for differences in

-fuel,'temperature, altitude or load. If the

carburetor does need adjustment, proceed as follows:

In general, turning idle mixture valve in !cloc kw_ise) decreases the supply of fuel to

.,me engine giving a leaner fuel/air mixture.

. Tuming the idle mixture valve out " .

-(cou_.."terclockwisa)"mcreases the Supply of

luel.tothe engine givi.nga richerfuel/air

rnixture_. -.-----_-

PREMMINARY SETTING -

o. Air oleaner assembly must be essem-

bled to the carburetor when making car- buretor adjustments.

•Be sure the throttle control cable is adjusted properly (see above).

FINAL SETTING -

•Start engine and allow to warm for five minutes. Make final adjustments with engine running and shift/motion control lever in neutral (14)position.

•Move throttle control lever to slow posi- tion. With finger, rotate and hold throttle lever against idle speed screw. Turn idle speed screw to attain 1750 RPM.

•While still holding throttle lever against

idle speed screw, turn idle mixture valve full travel clockwise then counterclock-

wise until engine runs rough. Turn valve to a point midway between those two

positions. Release throttle lever.

ACCELERATION TEST -

•Move throttle control lever from slow to fast position. If engine hesitates or dies, turn idle mixture valve out (counter- clockwise) 1/8 tum. Repeat test and

continue to adjust, if necessary, until engine accelerates smoothly.

High speed stop is factory adjusted; Do not adjust---d_,mage may resulL IMPORTANT: Never tamper with the engine governor, which is factory set for proper enginespeed, overspeeding the engine above the factory high speed set- ting can be dangerous, if you think the engine<3ovemed high speed needs adjusting, contact.your nearest authorized serviceconter, which has proper equip-

.ment to make any necessary adjusbn, ents.

Idle Speed Screw'-Tl_rottle Lever

IM .P.P.P.P.P.P.DamageP.P.P TAItor:the needle valve		Valve W'_h.
afid _	sea_ in carburetor may result if	_r
screw	is turned in too tight.	27

917.270711 specifications

The Craftsman 917.270711 is a robust and versatile lawn tractor designed to meet the needs of homeowners and landscape enthusiasts alike. Equipped with powerful features and cutting-edge technologies, this model stands out in the crowded market of lawn care equipment.

At the heart of the Craftsman 917.270711 is a reliable 24 HP Briggs & Stratton Intek V-Twin engine. This engine provides ample power, ensuring smooth operation even in demanding conditions. With a hydrostatic transmission, this lawn tractor offers effortless speed control, allowing users to easily navigate different terrains without the need for manual gear changes. The ergonomic design of the transmission lever enhances the user experience, making it intuitive and user-friendly.

One of the most notable features of the Craftsman 917.270711 is its 42-inch cutting deck. This deck allows for a wide cutting path, significantly reducing mowing time. Additionally, it comes equipped with three adjustable cutting heights, giving users the flexibility to achieve the desired grass length based on seasonal needs or personal preferences. The deck's design ensures efficient grass clipping dispersal, promoting a healthier lawn.

The cutting deck also features a deck wash system, which simplifies maintenance and cleaning. Users can easily attach a hose to the deck wash port, ensuring that the undercarriage remains free from grass buildup and debris.

Comfort is a priority in the design of the Craftsman 917.270711. It includes a comfortable high back seat that provides support during extended use. The tractor's steering wheel is conveniently positioned, ensuring easy maneuverability around obstacles such as trees and flower beds. Moreover, the ergonomically designed controls are within easy reach, providing a seamless user experience.

Safety features are critical in any lawn care equipment, and Craftsman has equipped the 917.270711 with essential safety innovations. A safety switch under the seat ensures that the engine stops if the operator dismounts, preventing accidents.

In summary, the Craftsman 917.270711 lawn tractor is a powerful and efficient machine designed for those seeking quality and convenience in lawn maintenance. With its reliable engine, hydrostatic transmission, adjustable cutting heights, and user-friendly features, it has cemented its position as a dependable choice for homeowners looking to maintain their lawns effortlessly.