Craftsman 917.2754 owner manual To Level Mower Housing, SIDE-TO-SIDE Adjustment, Belt Removal

Page 23

8.Place flat washer and clutch spring on idler pulley bolt and secure with small retainer spring.

9.Install belt onto engine pulley.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See "PROD-

UCT SPECIFICATIONS" section of this

manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance "A" on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjust- ment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift

link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

• Recheck measurements after adjusting.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut "E"

on both front links an equal number of turns.

•When distance "D" is 1/8" to 1/2"

lower at front than rear, tighten nuts "F" against trunnion on both front links.

•To raise front of mower, loosen nut"F" from trunnion on both front links. Tighten

nut "E" on both front links an equal num- ber of turns. The two front links must

remain equal in length.

•When distance "D" is 1/8" to 1/2" lower

at front than rear, tighten nut "F" against trunnion on both front links.

•Recheck side-to-side adjustment.

°°• o_° o 01

__Mandrel

Both Front Links Should be ual in Length

Bottom edge

Bottom edge of

of mower to

mower to ground

ground

--_t/

Arm

@

Lift Link N_

Adjustment

FRONT-TO-BACK ADJUSTMENT IMPORTANT: Deck must be level side-to side. If the following front-to-back adjust- ment is necessary, be sure to adjust both front links equally so mower will stay level side-to-side.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of trac- tor. Measure distance "D" directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjust- ments, check that both front links are

equal in length.

Nut "F"

Front Links

TO REPLACE MOWER BLADE DRIVE

BELT

The mower blade drive belt may be re- placed without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

1.Remove mower from tractor (See "TO REMOVE MOWER" in this section of manual).

2.Work belt off both mandrel pulleys and idler pulleys.

3.Pull belt away from mower.

BELT INSTALLATION -

1.Work belt around both mandrel pulleys and idler pulleys

2.Make sure belt is in all pulley grooves

23 and inside all belt guides.

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Jcrrftsmrnj Limited Warranty on Battery Limited Warranty on Craftsman Riding EquipmentGeneral Operation Safe Handling of Gasoline ServiceIV, Towi NG General Service Repair Protection Agreements Sears Installation ServiceCustomer Responsibilities Keys Carton Unpack Carton For AssemblyInstall Steering Wheel Install SeatOperation section for location Check BatteryCheck Deck Levelness ChecklistCheck for Proper Position of ALL Belts Checktire PressureProperty damage Lift Lever Plunger Used to release TractorStopping To Adjust Mower Cutting HeightTo SET Parking Brake To Move Forward and BackwardOperating in Reverse Using the Reverse Operation SystemTo Operate Mower To Stop Mower BladesBefore Starting the Engine Check Engine OIL Level To Start EngineMents Mowing Tips Automatic Transmission Warm UPPurge Transmission General Recommendations AS YOU Complete Regular ServiceTo Sharpen Blade TractorOperator Presence System Reverse Operation System ROS Blade RemovalBattery Engine Cooling System Clean AIR ScreenAIR Filter IN-LINE Fuel Filter CleaningMuffler Spark PlugsTo Remove Mower To Install MowerTo Replace Mower Blade Drive Belt To Level Mower HousingSIDE-TO-SIDE Adjustment Belt InstallationTo Replace Motion Drive Belt To Check and Adjust BrakeTo Adjust Brake To Check BrakeTo Remove Wheel for Repairs To Remove Hood and Grill AS Sembly Replacing BatteryTo Replace Headlight Bulb Engine To Adjust Throttle Control CableTo Adjust Carburetor Preliminary SettingCylinders Fuel SystemEngine OIL Start ProblemCause Correction ROS CauseOFF Problem Cause CorrectionPage Tractor - Model Number 917,275400 SchematicElectrical Part Description Electrical KEYTractor - Model Number 917,275400 Chassis and Enclosures KEY Part Description Tractor - Model Number 917.275400 Chassis and EnclosuresTractor - Model Number Ground Drive CAD Tractor - Model Number 917,275400 Steering Assembly Tractor - Model Number 917.275400 Steering Assembly KEY Part Optional EquipmentKEY Tractor - Model Number Seat AssemblyWheels & Tires Decals159460 Tractor - Model Number Lift AssemblyTractor - Model Number 917,275400 Mower Deck TUV Tractor - Model Number Mower DeckLo8 Peerless Transaxle Model Number LTH2000 Tractor Model Number20@ 6170 763@ 142117 PTO Set Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationIiiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiii Our Home

917.2754 specifications

The Craftsman 917.2754 is a state-of-the-art lawn tractor that stands out in the market for its robust features, advanced technologies, and practical design aimed at enhancing user experience and mowing efficiency. It is particularly favored by homeowners with extensive lawns, thanks to its powerful engine and user-friendly functionality.

One of the key features of the Craftsman 917.2754 is its powerful 24 HP engine, which provides ample horsepower to tackle various terrains and challenging mowing conditions. The engine is not only efficient but also reliable, ensuring that users can depend on it season after season. Coupled with a hydrostatic transmission, the driving experience is smooth, allowing for effortless control over speed and direction without the hassle of shifting gears.

The 42-inch cutting deck of the Craftsman 917.2754 is designed for optimal performance and efficiency. This size makes it perfect for maneuvering in tighter spaces while still covering a significant area of lawn in a single pass. The deck features an adjustable cutting height, allowing users to customize their mowing experience based on grass type and weather conditions, ensuring a clean and precise cut every time.

Another highlight of the Craftsman 917.2754 is its comfortable seating and ergonomic design. The high-back seat provides exceptional support, allowing users to maintain comfort during long mowing sessions. The intuitive control panel is user-friendly, equipped with easy-to-read dials and controls for direct access to critical functions such as throttle and cutting height adjustments.

For added convenience, the Craftsman 917.2754 also includes a tight turning radius, making it easier to navigate around obstacles like flower beds and trees. This feature reduces the need for additional trimming, saving users both time and effort. Furthermore, the integrated mulching capability allows for efficient grass recycling, promoting healthier lawn growth.

Durability is a hallmark of the Craftsman brand, and the 917.2754 exemplifies this with its sturdy construction and long-lasting components. Owners can enjoy peace of mind knowing that their investment is built to withstand the rigors of regular lawn maintenance.

In summary, the Craftsman 917.2754 lawn tractor combines power, efficiency, and comfort into a single machine, making it an excellent choice for homeowners looking to maintain their lawn effortlessly. Its advanced features and practical design set it apart in the lawn care landscape, providing users with a dependable and enjoyable mowing experience.
Top Page Image Contents