Craftsman 917.275764 owner manual To Level Mower Housing, To Replace Mower Blade Drive Belt

Page 24

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See "PRODUCT

SPECIFICATIONS" section of this man-

ual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of

mower to ground. Distance "A" on both sides of mower should be the same or

within 1/4" of each other.

•If adjustment is necessary, make adjust- ment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

•When distance "D" is 1/8" to 1/2" lower

at front than rear, tighten nuts "F" against trunnion on both front links.

•To raise front of mower, loosen nut "F" from trunnion on both front links. Tighten

nut "E" on both front links an equal number of turns. The two front links must

remain equal in length.

•When distance "D" is 1/8" to 1/2" lower

at front than rear, tighten nut "F" against trunnion on both front links.

•Recheck side-to-side adjustment.

Both Front Links Should be ual in Length

Bottom edge

Bottom

edge of

 

of mower to

mower to ground

 

_,o_ _ _

 

 

 

ground _IIZ_-ZZ

_t/

 

 

 

A; \ V-Gr=roundLin_e_-/

;

A

Nut "F"

Arm

Lift Link N_

Adjustment

FRONT-TO-BACK ADJUSTMENT

IMPORTANT: Deck must be level side-to side. If the following front-to-back adjust- ment is necessary, be sure to adjust both

front links equally so mower will stay level side-to-side.

To obtain the best cutting results, the mower housing should be adjusted so that

the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its

highest position.

Check adjustment on right side of trac- tor. Measure distance "D" directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjust- ments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut "E"

on both front links an equal number of turns.

Front Links

TO REPLACE MOWER BLADE DRIVE

BELT

The mower blade drive belt may be re- placed without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

1.Remove mower from tractor (See "TO REMOVE MOWER" in this section of

manual).

2.Work belt off both mandrel pulleys and idler pulleys.

3.Pull belt away from mower.

BELT INSTALLATION -

1.Work belt around both mandrel pulleys and idler pulleys

2.Make sure belt is in all pulley grooves and inside all belt guides.

3.Install mower (See "To Install Mower" in this section of this manual).

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Jcrrftsmrnj Days on Battery Year on TractorGeneral Operation Service III. ChildrenIV. Towing Safe Handling of GasolineGeneral Service Product AgreementsKeys Tools Required for Assembly Assemble Extension Shaft and BootInstall Steering Wheel Install SeatCheck Battery To Roll Tractor OFF Skid See Operation section for locationCheck Deck Levelness Check for Proper Position of ALL BeltsCheck Brake System Property damage Know Your Tractor Attachment Clutch Lever UsedTo SET Parking Brake StoppingTo Adjust Gauge Wheels Using the Reverse Operation SystemOperating in Reverse To Operate MowerTo Operate Hills To TransportTowing Carts and Other Attach Ments Before Starting the Engine Check Engine OIL LevelAutomatic Transmission Warm UP Purge TransmissionMowing Tips MA,.TE.A.SCCE.EOULE General RecommendationsCheck Operator Presence System Check Reverse Operation ROS SystemBlade Care Blade RemovalEngine Lubrication Clean AIR Screen Engine OIL FilterAIR Filter Engine Cooling SystemCleaning MufflerSpark Plugs IN-LINE Fuel FilterTo Install Mower To Remove MowerTo Level Mower Housing To Replace Mower Blade Drive BeltTo Check and Adjust Brake To Adjust BrakeTo Check Brake To Replace Motion Drive BeltTransaxle Motion Control LE VER Neutral Adjustment Transmission Removal ReplacementMent To Start Engine with a Weak BAT TeryReplacing Battery To Replace Headlight BulbTo Remove Hood and Grill AS- Sembly To Adjust Throttle Control Cable To Adjust CarburetorPreliminary Setting EngineBattery TractorEngine OIL CylindersProblem Cause CorrectionChoked Start EngineProblem Cause ContProblem Cause Correction OFFOlllll,o Electrical KEY Part Description Tractor - Model Number Chassis and Enclosures Tractor - Model Number Chassis and Enclosures Tractor - Model Number Ground Drive Tractor - Model Number Ground Drive 45% Tractor - Model Number Steering Assembly Optional Equipment KEY PartTractor - Model Number Seat Assembly Description Wheels & TiresTractor - Model Number Lift Assembly Tractor - Model Number Mower Deck Includes 206 KEY Part Description 434 1006 601 690946 Plug-Oil Drain 141 495931 Kit-Choke Strap-Starter Page Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down HILL, not Across Hill Degrees MAXSearsBrands,LLC

917.275764 specifications

The Craftsman 917.275764 is a powerful and efficient lawn tractor that exemplifies the blend of functionality, durability, and innovation, making it an ideal choice for homeowners who seek a reliable gardening tool. This model, part of Craftsman's renowned lineup, is specifically designed for cutting grass, maintaining larger lawns, and performing various yard tasks with ease.

One of the standout features of the Craftsman 917.275764 is its robust 24 HP Kohler engine. This engine delivers impressive power, ensuring that even the toughest grass and terrain can be tackled without difficulty. Its reliable performance allows users to complete lawn care activities more efficiently, making the tractor a valuable investment for maintaining a pristine yard.

Equipped with a 54-inch cutting deck, the Craftsman 917.275764 allows for a wide mowing path, enhancing productivity by reducing the number of passes needed to cover the lawn. The cutting height can be easily adjusted, offering multiple positions to suit different grass types and user preferences, thus guaranteeing an even cut. This flexibility enables users to tailor their mowing experience for optimal results.

The tractor features a hydrostatic transmission, providing a smooth driving experience without the need for manual gear shifting. This system not only simplifies operation but also allows for seamless speed adjustments while mowing, giving operators precise control over their mowing speed. The ergonomic design of the controls further enhances usability, making it easy for users of all skill levels to operate the tractor comfortably.

Adding to its practicality, the Craftsman 917.275764 includes a tight turning radius, allowing for greater maneuverability in gardens and around obstacles, making it an outstanding choice for yards with various features. Additionally, the tractor is compatible with various attachments, such as baggers and snow blowers, transforming it into a multi-functional tool for year-round use.

Safety is also a priority with the Craftsman 917.275764, featuring a seat safety switch that ensures the engine shuts off if the operator leaves the seat, reducing the risk of accidents. These features, combined with the rugged construction of the machine, reflect Craftsman's commitment to quality and safety.

In conclusion, the Craftsman 917.275764 lawn tractor stands out with its powerful engine, wide cutting deck, hydrostatic transmission, and versatile functionality. Whether for routine lawn maintenance or tackling more extensive yard work, this tractor offers homeowners an efficient and dependable solution for their gardening needs.
Top Page Image Contents