Craftsman 917.274031 owner manual Engine, Battery, Transaxle Cooling, Belts, Lubrication

Page 19

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. How-

ever, periodic charging of the battery with an automotive charger will extend its life.

Keep battery and terminals clean.

Keep battery bolts tight.

Keep small vent holes open.

Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to "leak" power.

1.Remove terminal guard.

2.Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor.

3.Rinse the battery with plain water and dry.

4.Clean terminals and battery cable ends with wire brush until bright.

5.Coat terminals with grease or petro- leum jelly.

6.Reinstall battery (See "REPLACING BATTERY" in the SERVICE AND AD-

JUSTMENTS section of this manual).

TRANSAXLE COOLING

Keep transaxle free from build-up of dirt and chaff which can restrict cooling.

V-BELTS

Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear.

ENGINE

LUBRICATION

Only use high quality detergent oil rated with API service classification SG-SL.

Select the oil'sSAE viscosity grade according to your expected operating temperature.

SAE VISCOSITY GRADES

*20

-30-20 .IOo1o 213

NOTE: Although multi-viscosity oils

(5W30, 10W30 etc.) improve starting in cold weather, they will result in increased oil consumption when used above 32°F. Check your engine oil level more frequent-

ly to avoid possible engine damage from running low on oil.

Change the oil after every 50 hours of op- eration or at least once a year if the tractor is not used for 50 hours in one year.

Check the crankcase oil level before start- ing the engine and after each eight (8) hours of operation. Tighten oil fill cap/

dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range expected before oil change. All oil must meet API service classification SG-SL.

Be sure tractor is on level surface.

Oil will drain more freely when warm.

Catch oil in a suitable container.

1.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine when changing oil.

2.Remove yellow cap from end of drain valve and install the drain tube onto the

fitting.

Oil Drain Valve

Closed and

Locked

Position_

) Drain

Tube

3.Unlock drain valve by pushing inward slightly and turning counterclockwise.

4.To open, pull out on the drain valve.

5.After oil has drained completely, close

and lock the drain valve by pushing inward and turning clockwise until the pin is in the locked position as shown.

6.Remove the drain tube and replace the cap onto the end of the drain valve.

7.Refill engine with oil through oil fill dip- stick tube. Pour slowly. Do not overfill.

For approximate capacity see "PROD- UCT SPECIFICATIONS" section of this manual.

8.Use gauge on oil fill cap/dipstick for checking level. For accurate reading, tighten dipstick cap securely onto the tube before removing dipstick. Keep oil at "FULL" line on dipstick. Tighten cap onto the tube securely when finished.

19

Image 19
Contents Lawn Tractor Limited Warranty on Battery Limited Warranty on Craftsman Riding EquipmentGeneral Operation II. Slope OperationDo not IV. ServiceIII. Children Page Sears Installation Service Product SpecificationsRepair Protection Agreements Keys Slope Sheet Video Cassette DrainTTo Remove Tractor from HOW to SET UP Your TractorCheck Battery Adjust SeatTo Convertto Bagging or Discharging Install Mulcher PlateCheck Deck Levelness ChecklistCheck Brake System Check Tire Pressure@@@@ Know Your Tractor Our tractors conform to the safety standardsHOW to USE Your Tractor To Operate Mower To Adjust Gauge WheelsTo Transport Before Starting the Engine Check Engine OIL Level Towingcarts and Other Attach MentsADD Gasoline Mulching Mowing Tips Mowing TipsZerk Lubrication ChartGeneral Recommendations Before Each USEBlade Care TractorBrake Operation Operator Presence SystemBelts BatteryEngine Transaxle CoolingAIR Filter Clean AIR INTAKE/COOLING AreasCleaning Engine OIL FilterTo Remove Mower To Install MowerTractor Depress clutch/brake pedal fully and set parking brakeBottomEdge To Level Mower HousingAlternate SIDE-TO-SIDE Recheck measurements after ad- justing?Nut To Check and Adjust BrakeTo Replace Mower Blade Drive Belt Belt RemovalFront Wheel TOE-IN/CAMBER Transaxle Gear Shift Lever NEU- Tral AdjustmentTo Adjust Steering Wheel ALIGN- Ment To Replace Motion Drive BeltTo Remove CABLES, Reverse Order Replacing BatteryTo Start Engine with Aweak BAT- Tery To Attach Jumper CablesTo Adjust Carburetor To Adjustthrottle Control CableWith Limiter Cylinders EngineFuel System Problem Troubleshooting ChartCause Correction Cause Problemcause Tractor - Model Number SchematicTractor - Model Number 917,274031 Electrical KEY Part Description Tractor - Model Number ElectricalTractor - Model Number 917.274031 Chassis and Enclosures Tractor - Model Number 917.274031 Chassis and Enclosures Tractor - Model Number Grounddrive NyUner 7/8 ID x .105 Hd Tractor - Model Number Ground DriveTractor - Model Number Steering T-3Axle Asm SpindleAsm LH SteeringTractor - Model Number Engine KEY Part NO. NO.DESCRIPTION Bolt Shoulder 5/16-18 uno Tractor - Model Number Seat AssemblyWheels &TIRES Tractor - Model Number DecalsTractor - Model Number Lift Assembly 179504 Plunger Assembly Tractor - Model Number Mower Deck KEY Part NO, no Tractor - Model Number DANATRANSAXLE-MODEL Number D4360-180 Housings use Loctite Ultra Gray Silicone Lo EMisSIONLABELI OlA Page Link-Throttle Bracket-Choke Control 19374 Suggested Guide for Sighting Slopes for Safe Operation 8E/ARS

917.274031 specifications

The Craftsman 917.274031 is a robust lawn tractor that combines performance, reliability, and user-friendly features, making it a popular choice among homeowners looking to maintain their lawns effectively. This machine is engineered with a powerful engine and innovative technologies that set it apart from standard riding mowers.

At the core of the Craftsman 917.274031 is a reliable 17.5 HP Briggs & Stratton engine, designed to deliver ample power for various cutting tasks. The engine features a vertical shaft design, which enhances efficiency and overall performance, while also ensuring easy starting. Complementing the engine is a 42-inch cutting deck, perfect for tackling medium to large-sized yards. This deck size offers an ideal balance of maneuverability and cutting capacity, enabling users to cover more ground in less time.

One of the standout features of the 917.274031 is its automatic transmission system, which provides a smooth and seamless driving experience. The hydrostatic transmission allows for effortless speed adjustments, enabling the operator to navigate tight spaces and diverse terrain with confidence. The cruise control feature further enhances user comfort during long mowing sessions by maintaining a consistent speed.

The lawn tractor is equipped with a comfortable, adjustable seat that promotes a better ergonomic position, making it suitable for extended use. The steering system is designed for easy handling, allowing users to make sharp turns without the risk of damaging the turf. Additionally, the inclusion of a deck wash system makes maintenance straightforward, as it enables quick cleaning of the cutting deck to prevent grass build-up.

Safety features are also highlighted in the Craftsman 917.274031. The operator presence control system ensures that the mower stops when the operator leaves the seat, minimizing the risk of accidents. The integrated headlights offer added visibility during early morning or late evening mowing sessions.

Overall, the Craftsman 917.274031 lawn tractor embodies a blend of power, comfort, and innovative features, making it an excellent option for homeowners seeking a reliable machine to keep their lawns in pristine condition. Its user-friendly technologies and focus on operator safety further enhance its appeal, making lawn care a more enjoyable task for users of all experience levels. Whether you are mowing, mulching, or bagging, this model is designed to deliver exceptional results every time.