To Adjustthrottle Control Cable

ENGINE

Maintenance, repair, or replacement of the emission control devices and systems, which are being done at the customers expense, may be performed by any non-read engine repair establishment or individual•Warranty repairs must be performed by an authorized engine manufactureCs service outlet.

The throttle control has been preset at the factory and adjustment should not be nec- essary. Check adjustment as described below before loosening cable. If adjust- ment is necessary, proceed as follows:

1.With engine not running, move throttle control lever from slow to choke posi- tion. Slowly move lever from choke to fast position.

2.Check that holes"A" in governor

control lever and hole in governor plate line-up. If holes "A" are not aligned, loosen clamp screw and move throttle cable until holes are aligned. Tighten

clamp	screw	securely.
TO ADJUST CARBURETOR
Governor	Control	Lever	Governor

Control Plate

Holes

ClampCable

Screw

NOTE: The carburetor on this engine is low emission. It is equipped with an idle fuel adjusting needle with a limiter cap, which allows some adjustment within the limits allowed by the cap. Do not attempt to remove the limiter cap. The limiter cap cannot be removed without breaking the adjusting needle.

The carburetor has been preset at the factory and adjustment should not be nec- essary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the

carburetor does need adjustment, proceed as follows:

In general, turning idle mixture valve in (clockwise) decreases the supply of fuel to the engine giving a leaner fuel/air mix- ture. Turning the idle mixture valve out (counterclockwise) increases the supply

of fuel to the engine giving a richer fuel/air mixture.

IMPORTANT: Damage to the needle

valve and the seat in carburetor may result if screw is turned in too tight.

PRELIMINARY SETTING -

1.Air cleaner assembly must be assem- bled to the carburetor when making carburetor adjustments.

2.Be sure the throttle control cable is adjusted properly (see above).

FINAL SETTING -

1.Start engine and allow to warm for five

•minutes. Make final adjustments with engine running and shift/motion control lever in neutral (N) position.

2.Move throttle control lever to slow posi- tion. With finger, rotate and hold throttle lever against idle speed screw. Turn idle speed screw to attain 1750 RPM.

3.While still holding throttle lever against idle speed screw, turn idle mixture valve full travel clockwise then coun-

terclockwise until engine runs rough. Turn valve to a point midway between those two positions. Release throttle lever.

ACCELERATION TEST -

4.Move throttle control lever from slow to fast position. If engine hesitates or dies, turn idle mixture valve out (coun- terclockwise) 1/8 turn. Repeat test and continue to adjust, if necessary, until

engine accelerates smoothly.

High speed stop is factory adjusted. Do not adjust - damage may result. IMPORTANT: Never tamper with the engine governor, which is factory set for proper engine speed. Overspeed- ing the engine above the factory high speed setting can be dangerous. If you think the engine-governed high speed needs adjusting, contact a Sears or other qualified service center, which has proper equipment and experience to make any necessary adjustments.

IdleThrottle Screw

Idle Mixture Valve-'f _

With Limiter

917.274031 specifications

The Craftsman 917.274031 is a robust lawn tractor that combines performance, reliability, and user-friendly features, making it a popular choice among homeowners looking to maintain their lawns effectively. This machine is engineered with a powerful engine and innovative technologies that set it apart from standard riding mowers.

At the core of the Craftsman 917.274031 is a reliable 17.5 HP Briggs & Stratton engine, designed to deliver ample power for various cutting tasks. The engine features a vertical shaft design, which enhances efficiency and overall performance, while also ensuring easy starting. Complementing the engine is a 42-inch cutting deck, perfect for tackling medium to large-sized yards. This deck size offers an ideal balance of maneuverability and cutting capacity, enabling users to cover more ground in less time.

One of the standout features of the 917.274031 is its automatic transmission system, which provides a smooth and seamless driving experience. The hydrostatic transmission allows for effortless speed adjustments, enabling the operator to navigate tight spaces and diverse terrain with confidence. The cruise control feature further enhances user comfort during long mowing sessions by maintaining a consistent speed.

The lawn tractor is equipped with a comfortable, adjustable seat that promotes a better ergonomic position, making it suitable for extended use. The steering system is designed for easy handling, allowing users to make sharp turns without the risk of damaging the turf. Additionally, the inclusion of a deck wash system makes maintenance straightforward, as it enables quick cleaning of the cutting deck to prevent grass build-up.

Safety features are also highlighted in the Craftsman 917.274031. The operator presence control system ensures that the mower stops when the operator leaves the seat, minimizing the risk of accidents. The integrated headlights offer added visibility during early morning or late evening mowing sessions.

Overall, the Craftsman 917.274031 lawn tractor embodies a blend of power, comfort, and innovative features, making it an excellent option for homeowners seeking a reliable machine to keep their lawns in pristine condition. Its user-friendly technologies and focus on operator safety further enhance its appeal, making lawn care a more enjoyable task for users of all experience levels. Whether you are mowing, mulching, or bagging, this model is designed to deliver exceptional results every time.

ENGINE