Craftsman 917.370741 owner manual Lawn Mower, Tires

Page 14

LAWN MOWER

Always observe safety rules when per- forming any maintenance.

TIRES

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

DRIVE WHEELS

Check rear drive wheels each time you mow to be sure they move freely. The wheels not turning freely means trash,

grass cuttings, etc., may be inside the drive wheel and dust cover area and must

be cleaned out to free drive wheels.

If necessary to clean the drive wheels, check both rear wheels.

BLADE CARE

For best results, blade must be kept sharp. Replace a bent or damaged blade.

_, CAUTION: Use only a replacement blade approved by the manufacturer of your mower. Using a blade not approved by the manufacturer of your mower is hazardous, could damage your mower and void your warranty.

TO REMOVE BLADE

1.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

2.Turn lawn mower on its side. Make sure air filter and carburetor are up.

3.Use a wood block between blade and

mower housing to prevent blade from turning when removing blade bolt.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

4.Remove blade bolt by turning counter- clockwise.

5.Remove blade and attaching hardware (bolt, lock washer, hardened washer).

NOTE: Remove the blade adapter and check the key inside hub of blade adapter. The key must be in good condition to work

properly. Replace adapter if damaged.

TO REPLACE BLADE

1.Position the blade adapter on the en- gine crankshaft. Be sure key in adapter and crankshaft keyway are aligned.

2.Position blade on the blade adapter aligning the two (2) holes in the blade with the raised lugs on the adapter.

3.Be sure the trailing edge of blade (oppo-

site sharp edge) is up toward the engine.

4.Install the blade bolt with the lock washer and hardened washer into blade adapter and crankshaft.

5.Use block of wood between blade and

lawn mower housing and tighten the blade bolt, turning clockwise.

•The recommended tightening torque is 35-40 ft. Ibs. / 47-54 N-m.

IMPORTANT: Blade bolt is heat treated. If bolt needs replacing, replace only with

approved bolt shown in the Repair Parts section of this manual.

Blade adapter

Crankshaft

Lockwasher _ Key /

i

bolt Hardened

washerCrankshaft

TO SHARPEN BLADE

NOTE: We do not recommend sharp-

ening blade - but if you do, be sure the blade is balanced. An unbalanced blade

will cause eventual damage to lawn mower or engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, drive a nail into a beam or wall. Leave about one inch of

the straight nail exposed. Place center hole of blade over the head of the nail.

If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

GRASS CATCHER

•The grass catcher may be hosed with water, but must be dry when used.

•Check your grass catcher often for dam-

age or deterioration. Through normal use it will wear. If catcher needs replac- ing, replace only with approved replace-

ment catcher shown in the Repair Parts section of this manual. Give the lawn

mower model number when ordering.

GEAR CASE

•To keep your drive system working properly, the gear case and area around the drive should be kept clean and free of trash build-up. Clean under the drive cover twice a season.

•The gear case is filled with lubricant to the

proper level at the factory. The only time the lubricant needs attention is if service

has been performed on the gear case.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents CRnFTSMFIN Year Full Warranty on Craftsman Lawn Mower Sears, Roebuck and Co., Hoffman Estates, ILIII Children GeneralII. Slope Operation IV. Safe Handling GasolineGeneral Service API SG-SL SAESears Installation Service Repair Protection AgreementsMower From HOW to SET UP Your Mower To Unfold HandleRemove Mowing PositionTo Assemble Grass Catcher To Prepare BatteryTo Install Attachments Operator Presence Control Lever Meets Cpsc Safety RequirementsKnow Your Lawn Mower Auxiliary Starter HandleEnginezonecontrol HOW to USE Your Lawn Mower EnginespeedTo Adjust Cutting Height Simple Steps to Remember When Converting Your Lawn Mower To Stop Engine Before Starting Engine ADD OILADD Gasoline To Start EngineMowing Tips Mulching Mowing TipsBefore Each USE Spray lubricant See Engine in Maintenance sectionGeneral Recommendations LU BricationLawn Mower TiresEngine LU Brication Clean Under Drive Cover CleaningLawn Mower To Adjust Cutting Height Rear DeflectorCarburetor To Adjust HandleEngine Engine Speed HandleAT T E RY EngineDoes not start OFFProblem SU Seguridad Esta Comprometida Despues de manipularlosHacer OperacionII. Operacion Sobre LAS Cuestas No HacerServicio RJ 19LMRendimiento DE LA Segadora Acuerdos de Protecci6n para la Reparaci6nServicio de Instalacion Sears Mantenimiento DE LA SegadoraPara Remover LA Segadora DE LA Caja DE Carton Como Preparar SU Segadora Para Desdoblar EL MangoPara Instalar LOS Accesorios Cumple CON LOS Requisitos DE Seguridad DE LA Cpsc Barra de control de la impulsi6n se usaAjuste DEL Mando Como Usarsu Segadora Velocidad DEL MotorControl DE LA Impulsion Para Montar Y Adjuntar EL RECOGE- DOR DE C#SPEDSegadoras CON Descarga Trasera Segadoras CON Descarga LateralPara Convertir LA Segadora LA Segadora Esta Lista Para LAImportante Antes DE Hacer Arrancar ELMotor Agregue Aceite Agregue GasolinaOnsejos Para Segar Consejos Para Segar Y AcolcharAntes DE Cada USO LubricacionRuedas DE Impulsion Recogedor DE CospedPara Cambiar EL Aceite DEL Motor MotorFiltro DE Aire BujjaPara Remover LA Correa DE Impulsion LimpiezaSegadora Para Ajustar LA Altura DE Corte Limpie Debajo DE LA Cubierta DE LAMotor Velocidad DEL Motor ParacambiarlacorreadeimpulsionPara Ajustar EL Mango Motor Sistema DE Combustible SegadoraMango Aceite DEL MotorCorreccion ProblemaCausa No arrancaProblema Causa Page Ooo LLI 9999 Briggs & Stratton 4-CYCLE Engine Emissions Label Carburetor Gasket SET Carburetor Overhaul KIT668 Briggs & Stratton 4-CYCLE Engine Model NumberEngine Gasket SET 621 163 745Briggs Stratton 4-CYCLEENGINE KEY Part DescriptionOur Home

917.370741 specifications

The Craftsman 917.370741 is a reliable and robust riding lawn mower designed to tackle various lawn maintenance tasks with ease and efficiency. Built with user-friendly features and advanced technology, this model stands out as a preferred choice for homeowners seeking durability and performance in their outdoor equipment.

One of the primary features of the Craftsman 917.370741 is its powerful engine. Equipped with a 24 HP Briggs & Stratton V-twin engine, this mower offers superior performance, ensuring that users can handle even the toughest grass and terrain with confidence. The engine is designed for enhanced fuel efficiency, which translates to longer mowing sessions without the need for frequent refueling.

The mower features a 42-inch cutting deck, allowing for a wide cutting path that reduces mowing time. This deck is constructed from sturdy materials, designed to withstand the rigors of outdoor use while providing a clean and even cut. The mowing height can be easily adjusted from 1.5 to 4 inches, allowing users to customize the cutting height to suit their lawn's specific needs.

Another notable characteristic of the Craftsman 917.370741 is its ease of maneuverability. The mower is equipped with a hydrostatic transmission, which allows for seamless speed changes without the need for shifting gears. This feature enables smoother operation and increased control, making it easier for users to navigate around landscaping, trees, and other obstacles.

The riding mower is also designed with comfort in mind. It features a high-back seat that provides ample support during long mowing sessions, reducing fatigue. The ergonomic controls are easy to reach, ensuring that users can operate the mower efficiently without straining.

In terms of maintenance, the Craftsman 917.370741 is designed for longevity. The engine has an easy-access oil filter and offers quick-release blades for convenient maintenance and replacement. Additionally, the mower’s construction uses corrosion-resistant materials, increasing its durability and lifespan.

Finally, the Craftsman 917.370741 comes equipped with safety features that protect both the user and the machine. The mower includes an automatic blade brake, ensuring that the blades stop quickly when the operator leaves the seat. This feature enhances safety, especially on uneven terrain where accidents could occur.

Overall, the Craftsman 917.370741 combines power, precision, and comfort, making it a top choice for anyone looking to maintain their lawn effectively and efficiently. With its robust engine, easy maneuverability, and thoughtful design, this riding mower is well-suited for a variety of lawn care tasks.
Top Page Image Contents