Craftsman 917.28991 manual Transmission, Replacing Battery

Page 30

REPLACING BATTERY

_WARNING: Do not short batteryterminals

by allowing a wrench or any other object to contact both terminals at the same time.

Before connecting battery, remove metal

bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding.

1.Lift hood to raised position.

2.Disconnect BLACKbatterycable (A) then RED battery cable and carefully remove battery from tractor.

3.Install new battery with terminals in same position as old battery.

4.First connect RED battery cable (B) to

positive (+) batteryterminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover (C) over terminal.

5.Connect BLACKgrounding cableto neg- ative (-) battery terminal with remaining hex bolt and keps nut. Tighten securely.

6. Close hood.

( _ Negative

 

(Black)

 

Cable

Positive

(Red)

CableA

TO REPLACE HEADLIGHT BULB

1.Raise hood.

2.Remove bulb holder from the hole in the backside of the grill.

3.Replace bulb in holder and install bulb holder securely back into the hole in the backside of the grill.

4.Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractorto run poorly, stop running, or prevent it from starting.

•Check wiring.

TO REPLACE FUSE

Replace with 30 amp automotive-type plug- in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL AS- SEMBLY

1.Raise hood.

2.Unsnap headlight wire connector.

3.Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

4.When replacing hood, be sure to recon- nect the headlight wire connector.

Hood

Headlight Wire

Connector

TRANSMISSION

REMOVAL/REPLACEMENT

Should your transmission require removal for

service or replacement, it should be purged

after reinstallation and before operating the

tractor. See "PURGE TRANSMISSION" in the Operation section of this manual.

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary Check adjustment as described below before loosening cable. If adjustment is necessary, see engine manual.

TO ADJUST CHOKE CONTROL

The choke control has been preset at the factory and adjustment should not be necessary. If adjustment is necessary, see engine manual.

TO ADJUST CARBURETOR

Your carburetor has been preset at the factory

and adjustment should not be necessary. However, minor adjustment may be required

to compensate for differences in fuel, tem- perature, altitude or load. If the engine does

need adjustment, see engine manual.

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Crrftsmrii SEARS, Roebuckand CO., Hoffman ESTATES, IL 60179 U.S.ACraftsman Full Warranty TWO Years on RiDiNG EquipmentGeneral Operation Service IV. TowingSafe Handling of Gasoline Extra Repair Protection Product SpecificationsSears Installation Service AgreementsMower Front Wheel 1/40.D. WasherFrom Skid To Remove Tractor from CartonBefore Removing Tractor Unpack CartonAssemble Front Gauge Wheel To Front of Mower Turn Steering Wheel Left and Position MowerSlide Mower Under Tractor Attach Mower Side Suspension Arms a to Chassis Install ANTI-SWAY BAR S if EquippedANTI-SWAY BAR S Attach Rear Lift Links CAttach Front Link E Install Belt on Engine Clutch Pulley MMower Drive Belt Installation IcautionCheck for Proper Position Check Tire PressureCheck Deck Levelness Check Brake System@@@@ Light Switch Turns the headlights on and off Attachment Clutch SwitchKnow Your Tractor Stopping Ground Drive HOW to USE Your TractorStopping Mower Blades EngineTo Move Forward and Backward System CharacteristicsTo Adjust Gauge Wheels To Operate MowerTo Operate On Hills Using the Reverse Operation SystemTo Stop Mower Blades = To TransportTo Start Engine Service REMINDER/HOUR MeterBefore Starting the Engine Check Engine OIL LevelPurge Transmission Automatic Transmission Warm UPMowing Tips General Recommendations Maintenance ScheduleChart Before Each USECheck Reverse Operation ROS System TractorCheck Operator Presence System TiresEngine To Change Engine OILLubrication To Service Cartridge MufflerSpark Plugs Cleaning Movable partsDeck Washout Port To Install Mower To Remove MowerPrecision SIDE-TO-SIDE Adjustment Visual SIDE-TO-SIDE AdjustmentFRONT-TO-BACK Adjustment To Level MowerTo Replace Mower Drive Belt To Attach Jumper Cables Replacing Battery TransmissionFuel System BatteryOther Engine OILProblem Cause Correction Will not startEngine will not turn over Problemcause CorrectionProblem Cause Discharge Headlights not working If so equippedProblem Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXMontaje/PreOperaci6n ReglasdeSeguridadEspecificacionesdelProducto Garantia Completa DE CraftsmanAdvertencia FuncionamientoGeneral AdvertenoiaIV. Remolque III. NinosManipulacion Segura DE LA GasolinaPage Especificaciones DEL Producto Acuerdo DE RepuestoResponsabilidades DEL Cliente Rueda delantera de la segadore Tuerca de 1/40.D. ArandelaResorte de Retenci6n Antioscilaci6n Barra Verifique LA BATERiA LA CorrederaInstale LA Segadora Arme LA Rueda Calibradora Delan Deslice LA Cortadora DE Cesped Debajo DEL TractorBarra Antibalanceo Instale LOS Eslabones DE LEVAN- Tamiento Traseros CInstale EL Eslabon Delantero E ParaReemplazar LA Correa DE LA Segadora Instale LA Correa EN LA Polea DEL Embrague DEL Motor MLista DE Revision Revision DE LA Presion DE LAS LlantasRevision DE LA NIVELACI6N DEL CON Junto @@@ Palanca DE Mando Crucero Familiaricese CON SU TractorSU Tractor Pedal DE Marcha AdelanteComo Usar SU Tractor MientoPara Ajustar LA Altura DE Corte DE Moverse Hacia Adelante Y Hacia AtrasUtilizar EL Mando Crucero LA SegadoraPara Operar EN Cerros Para Operar LA SegadoraPara Parar LAS Cuchillas DE LA Sega Usar EL Sistema DE Funcionamiento ATR,,SMECA.NISMO DE Aviso DE Servicio / Cronometro Para TransportarRemolque DE Carretillas O Otros Acoesorios Agregue GasolinaPara Hacer Arrancar EL Motor Arranque CON Tiempo Templado 50F/10C Y M,SCalentamiento Para LA Transmision Automatica Purgar LA Transmision Consejos Para SegarRecomendaciones Generales Antes DE Cada USOTabla VI= Rifiez Sistema Func Ionam Iento AT R/,S ROS TractorLlantas Cuidado DE LA CuchillaMotor Lubricacion Limpieza Mang Puerto de Lavado Adaptador de Boq CIO O DE Hacer Ajustes Para Desmontar LA Cortadora DEPara Instalar LA Segadora Regulacion DE LA Precision DE Lado Para Nivelar LA SegadoraRegulacion Visual DE Lado a Lado Ajuste DE Delante a ATR,SDE Movimiento Montaje DE LA Correa DE LA SegadoraPara Cambiar LA Correa DE Impulsion Desmontaje DE LA CorreaVerifique EL Freno Control DEL FrenoParaadj Untar LOS Cables DE EM Palm E Para Cambiar EL Fusible TransmisionMotor Para Remover EL Conjunto DEL Capo Y DEL EnrejadoSistema DE Combustible TractorOtros Aceite DEL MotorProblema Causa Correccion ESTRANGULACI6N ChokeIdentificacion DE Problemas ContinuadoProblema CorreccionApagado Page Operacion Segura Your Home Our Home

917.28991, 28991 specifications

The Craftsman 28991, also referred to by its model number 917.28991, is a robust lawn mower designed for efficiency and convenience in residential landscaping. This particular model is tailored to meet the diverse needs of homeowners who seek a reliable solution for lawn care.

One of the foremost features of the Craftsman 28991 is its powerful engine. Equipped with a high-performance, gasoline-powered engine, it delivers ample power to tackle various types of grass and terrain. The engine’s design emphasizes reliability, ensuring that users can depend on it without frequent maintenance issues.

The mower includes a versatile cutting deck that is adjustable, offering multiple height settings. This adjustment capability allows users to customize the cutting height to suit their lawn type and personal preferences. Whether you prefer a low trim for a manicured look or a higher cut for a more natural appearance, this mower accommodates those needs effortlessly.

With a focus on user comfort, the Craftsman 28991 features an ergonomic handle. The handle's design is meant to reduce fatigue during extended mowing sessions, allowing for a more pleasant mowing experience. The mower also incorporates a self-propelling mechanism, which makes it easier to maneuver across varying terrains, especially on slopes or uneven ground.

In terms of technology, the Craftsman 28991 offers a bagging option alongside mulching capabilities. The rear bag collects grass clippings, reducing the need for additional yard cleanup, while the mulching feature finely chops the clippings, returning vital nutrients back to the lawn. This dual-functionality promotes a healthier lawn while simplifying the mowing process.

The construction of the Craftsman 28991 highlights durability. Its steel deck is designed to withstand the rigors of frequent use, ensuring longevity while maintaining performance. Additionally, the design includes oversized wheels that enhance traction and maneuverability, making it suitable for navigating tight spaces and obstacles.

Overall, the Craftsman 28991,917.28991 is an exceptional choice for homeowners looking for a dependable, feature-rich mower. With its powerful engine, adjustable cutting deck, ergonomic design, and dual-functioning capabilities, it stands out as a reliable tool for achieving a well-maintained lawn with minimal effort.
Top Page Image Contents