Craftsman 917.374356 owner manual Engine Speed

Page 8

The operation of any lawn SAFETVG'ASSESmower can result in foreign

objects thrown into the eyes, which can result in severe

eye damage. Always wear safety glasses or eye shields while oper- ating your lawn mower or performing any adjustments or repairs. We recommend a standard safety glasses orwide vision safety mask worn over spectacles.

HOW TO USE YOUR LAWN MOWER

ENGINE SPEED

Engine speed was set at the factory for optimum performance. It is not adjustable.

ENGINE ZONE CONTROL

• ILCAUTION: Federal regulations require

an engine control to be installed on this lawn mower in order to minimize the

risk of blade contact injury. Do not under any circumstances attempt to defeat the function of the operator control. The blade turns when the engine is running.

Your lawn mower is equipped with an operator presence control bar which

requires the operator to be positioned behind the lawn mower handle to start

and operate the lawn mower.

DRIVE CONTROL

Self-propelling is controlled by hold- ing the operator presence control bar

down to the handle and pulling the drive control lever rearward to the handle.

The further toward the handle the lever

is pulled, the faster the unit will travel.

. Forward motion will stop when either the operator presence control bar or drive control lever are released. To stop forward motion without stopping engine, release the drive control lever only. Hold operator presence control bar down against handle to continue mowing without self-propelling.

NOTE: If after releasing the drive control the mower will not roll backwards, push the mower forward slightly to disengage drive wheels.

DRIVE CONTROL ADJUSTMENT

Over time, the drive control system may become "loose", resulting in decreased speed. There is a turnbuckle on the drive control housing to increase tension on the drive cable. Proceed as follows:

1.Turn unit off and disconnect spark plug wire from spark plug.

2.Rotate turnbuckle on drive control to increase drive speed.

3.Operate mower to test drive speed. Readjust as required.

4.If condition fails to improve after the above steps (forward speed remains the same), your drive belt is worn and should be replaced.

Adjustment turnbuckle

TO ADJUST CUTTING HEIGHT

Raise wheels for low cut and lower wheels for high cut, adjust cutting height to suit

your requirements. Medium position is best for most lawns.

To change cutting height, pull up on adjuster lever, move wheel up or down

to suit your requirements and release adjuster lever. Be sure all wheels are in the same setting.

NOTE: Adjuster is properly positioned when lever inserts into hole in plate.

LEVER BACKWARD 4 i

TO LOWER MOWER

Plate

Operator presence control bar Drive control

TO

 

lever

ENGAGE

DRIVE

LEVER

DRIVE

CONTROL

FORWARD

CONTROL

DISENGAGED

8 TO RAISE MOWER

 

 

Image 8
Contents Craftsman Yearfull Warranty on Craftsman Lawn Mower Your Safety is InvolvedDo not General OperationIV. Safe Handling of Gasoline General Service RJ19HXLawn Mower Maintenance Lawn Mower PerformanceTo Remove Mower from Carton To Unfold HandleTo Assemble Grass Catcher MowingMeets Cpsc Safety Requirements Know Your Lawn MowerEngine Speed Rear Bagging Side DischargingFor Rear Bagging To Convert MowerBefore Starting Engine Mulching Mowing Tips Mowing TipsSee Engine in Maintenance section General RecommendationsBefore Each USE LubricationLawn Mower Drive WheelsTo Clean AIR Filter Grass CatcherGear Case Engine LubricationCleaning Clean Under Drive CoverWater Washout Feature MufflerTo Adjust Handle Rear DeflectorTo Remove Drive Belt To Replace Drive BeltCarburetor HandleEngine Speed Fold Forward for Storage Mowing PositionProblem Cause Correction OtherFuel System Engine OILProblemcause Need More HELP?Sears, Roebuck and Co., Hoffman Estates, IL SU Seguridad Esta ComprometidaOperacion III. NinosII. Operacion Sobre LAS Cuestas HacerSAE RJ19HXServicio de Instalaci6n Sears Rendimiento DE LA SegadoraMantenimiento DE LA Segadora Como Preparar SU Segadora Familiaricese CON SU Segadora Producto. Aprenda y comprenda sus significadosImpulsi6n Como Usar SU SegadoraVelocidad DEL Motor Para Convertir LA Segadora Segadoras CON Descarga TraseraSegadoras CON Descarga Lateral Para Ensacamiento TraseroPara Parar EL Motor Antes DE Hacer Arrancar EL MotorImportante Onsejos Para Segar Consejos Para Segar Y ACOL- CharRecomendaciones Generales Antes DE Cada USOLubricacion Tabla DE LubricacionLlantas Ruedas DE IMPULSI6NCuidado DE LA Cuchilla Para Remover LA CuchillaMotor Lubricacion Limpie Debajo DE LA Cubierta DE LA Impulsion LimpiezaDerrubio DEL Agua Segadora LA Altura DE CorteDesviador Trasero Para Remover Correa DE ImpulsionMotor Velocidad DEL MotorCarburador MangoProblema Causa MotorAceite DEL Motor CilindroProblema CausaPage Ooo \ \ Aoo 84J Briggs & Stratton 4-CYCLE Engine19o 334 524 ? KEY Part Description Briggs & Stratton Cycle EngineModel Number 690959 Pin-Locating Need More HELP? Your Home