Craftsman 917.376233 owner manual Lawn Mower, Drive Wheels

Page 13

LAWN MOWER

Always observe safety rules when per- forming any maintenance.

TIRES

Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

DRIVE WHEELS

Check front drive wheels each time before you mow to be sure they move freely.

The wheels not turning freely means trash,

grass cuttings, etc. are in the drive wheel area and must be cleaned to free drive wheels.

If necessary to clean the drive wheels, be sure to clean both front wheels.

1.Remove hubcaps, Iocknuts & washers.

2.Remove wheels from wheel adjusters.

3.Remove any trash or grass cuttings from inside the dust cover, pinion and/ or drive wheel gear teeth.

4.Put wheels back in place.

NOTE: If after cleaning, the drive wheels do not turn freely, contact a Sears or other qualified service center.

BLADE CARE

For best results, mower blade must be kept sharp. Replace a bent or damaged blade. A CAUTION: Use only a replacement blade approved by the manufacturer of your mower. Using a blade not approved by the manufacturer of your mower is haz- ardous, could damage your mower and void your warranty.

TO REMOVE BLADE

1.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

2.Turn lawn mower on its side. Make sure air filter and carburetor are up.

3.Use a wood block between blade and

mower housing to prevent blade from turning when removing blade bolt.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

4.Remove blade bolt by turning counter- clockwise.

5.Remove blade and attaching hardware

(bolt, lock washer, hardened washer). NOTE: Remove the blade adapter and check the key inside hub of blade adapter. The key must be in good condition to work properly. Replace adapter if damaged.

TO REPLACE BLADE

1.Position the blade adapter on the en- gine crankshaft. Be sure key in adapter and crankshaft keyway are aligned.

2.Position blade on the blade adapter.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on blade adapter.

3.Be sure trailing edge of blade (opposite sharp edge) is up toward the engine.

4.Install the blade bolt with the lock washer and hardened washer into blade adapter and crankshaft.

5.Use block of wood between blade and

lawn mower housing and tighten the blade bolt, turning clockwise.

The recommended tightening torque is 35-40 ft. Ibs.

IMPORTANT: Blade bolt is heat treated. If bolt needs replacing, replace only with approved bolt shown in the Repair Parts section of this manual.

Blade adapter

Key

Crankshaft

Lockwasher

 

 

Blade

 

....',,

Blade

 

_

 

 

bolt

Hardened

:_,:,,,",

/ \ '\

 

 

washer

Trailing

edge

retainer

TO SHARPEN BLADE

NOTE: We do not recommend sharp-

ening blade - but if you do, be sure the blade is balanced. An unbalanced blade

will cause eventual damage to lawn mower or engine.

The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with it.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain m a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

Center hole

5/8" bolt or pin

13Blade

Image 13
Contents Craftsman Your Safety is Involved Yearfull Warranty on Craftsman Lawn MowerIV. Safe Handling of Gasoline General OperationDo not RJ19HX General ServiceLawn Mower Performance Lawn Mower MaintenanceTo Unfold Handle To Remove Mower from CartonTo Assemble Grass Catcher MowingKnow Your Lawn Mower Meets Cpsc Safety RequirementsHOW to USE Your Lawn Mower To Empty Grass Catcher Before Starting EngineFor Rear Bagging ADD OILTo Start Engine To Stop EngineMowing Tips Mulching Mowing TipsBefore Each USE General RecommendationsLubrication Before After EveryDrive Wheels Lawn MowerGrass Catcher To Clean AIR FilterGear Case EngineClean Under Drive Cover CleaningMuffler Spark PlugRear Deflector To Adjust HandleTo Remove Drive Belt To Replace Drive BeltCarburetor EngineHandle Fuel System OtherEngine OIL CylinderCause ProblemCorrection Need More HELP?SU Seguridad Esta Comprometida Sears, Roebuck and Co., Hoffman Estates, ILIII. Ninos OperacionII. Operacion Sobre LAS Cuestas HacerRJ19HX SAEMantenimiento DE LA Segadora Rendimiento DE LA SegadoraServicio de Instalaci6n Sears Como Preparar SU Segadora Cumple CON LOS Requisitos DE Seguridad DE LA Cpsc Producto. Aprenda y comprenda sus significadosVelocidad DEL Motor Como Usar SU SegadoraImportante Antes DE Hacer Arrancar EL MotorPara Parar EL Motor Para Hacer Arrancar EL MotorConsejos Para Segar Y ACOL- Char Onsejos Para SegarAntes DE Cada USO Recomendaciones GeneralesLubricacion Tabla DE LubricacionSegadora Motor Lubricacion Limpie Debajo DE LA Cubierta DE LA IMPULSI6N LimpiezaDesviador Trasero Para Ajustar LA Altura DE CortePara Remover Correa DE Impulsion Para Ajustar EL MangoVelocidad DEL Motor MotorCarburador SegadoraCilindro Problema CausaOtros Causa Problema28/1 Part KEYDESCRiPTiON SAE 30WCraftsman Rotary Lawn Mower - Model Number Frame, Grassbag KEY Part Description22i 2o 972 6o81 Engine Gasket SET Engine Power Rating informationValve Gasket SET Oversize Briggs & Stratton 4-CYCLE EngineLever 972 699374 Tank-Fuel 523 499621 Your Home Need More HELP?

917.376233 specifications

The Craftsman 917.376233 is a riding lawn mower specifically designed for the homeowner seeking a blend of durability, performance, and comfort. This model stands out in the Craftsman line-up, providing a robust set of features that cater to a variety of lawn care needs.

One of the key features of the Craftsman 917.376233 is its powerful engine. Equipped with a 19 horsepower Briggs & Stratton engine, this mower offers reliable power for tackling larger lawns and rough terrain. The engine is designed for optimal performance, ensuring that the mower operates smoothly and efficiently during operation.

The mower features a 42-inch cutting deck, which strikes an ideal balance between maneuverability and cutting capacity. This width allows for efficient mowing in medium to large yards while still being able to navigate tight spaces, such as flower beds and pathways. The adjustable cutting height also provides users with the flexibility to achieve the desired grass length, with multiple positions available to suit different lawn conditions.

In addition to its performance features, the Craftsman 917.376233 incorporates advanced technologies to enhance user experience. The manual transmission with a seven-speed gear shift allows operators to easily adjust their speed based on the lawn’s terrain. This provides better control and precision while mowing.

Comfort is also a significant focus in the design of this model. The high-back seat and ergonomic steering wheel ensure that users can operate the mower for extended periods without discomfort. The convenient foot-pedal design allows for easy speed adjustments, while the easy-access controls promote a user-friendly experience.

The mower is designed with durability in mind. Its heavy-duty steel frame and cutting deck construction ensure that it can withstand the rigors of regular use, making it a long-lasting investment for homeowners. Coupled with a reliable maintenance schedule, the Craftsman 917.376233 is built to provide years of dependable service.

Overall, the Craftsman 917.376233 combines power, versatility, and user comfort, making it an excellent choice for homeowners looking to maintain the beauty of their lawns. Its thoughtful features and solid construction make it a model that stands out in the competitive landscape of riding lawn mowers.