Craftsman 917.37181 owner manual To Replace Drive Belt, To Adjust Handle, Engine, Carburetor

Page 17

TO REPLACE DRIVE BELT

1.Place new drive belt in the belt retainer of the debris shield. Be sure to route belt between belt keepers and through slot (See Figure D).

Belt retainer.

Tab

Belt

Drive belt

Debris

Slot shield

TO ADJUST HANDLE

The handle on your lawn mower has multiple height positions - adjust to height that suits you.

1.Remove knob and carriage bolt on left side of the lower handle.

2.While holding handle assembly, re- move knob and carriage bolt from right side. Align hole in handle with desired hole in handle bracket, then reassem- ble bolt and knob and tighten securely.

3.Align left side of handle with same po-

sitioning hole as right side and secure with bolt and knob.

KnobBolt

\

Figure D

2.Route the other end of the new drive belt through hole in housing.

3.Reattach debris shield to housing with screw previously removed. Be sure tab of debris shield is in gap of housing.

4.Position blade on the blade adapter aligning the two (2) holes in the blade with the raised lugs on the adapter.

5.Be sure the trailing edge of blade (op- posite sharp edge) is up toward the

engine (See Figure C).

6.Install the blade bolt with the lock washer and hardened washer into blade adapter and crankshaft.

7.Use block of wood between blade and

lawn mower housing and tighten the blade bolt, turning clockwise.

The recommended tightening torque is 35-40 ft. Ibs.

IMPORTANT: Blade bolt is heat treated. If bolt needs replacing, replace only with

approved bolt shown in the Repair Parts section of this manual.

8.Return mower to upright position.

9.Install new drive belt into idler arm

assembly, then around the drive pulley. Be sure belt is inside of belt keepers (See Figure B).

NOTE: Pulling on the drive belt (to install

it on the drive pulley) will cause the other end of the belt to free itself from the debris

shield retainer and properly seat itself in groove of pulley end of the blade adapter.

10.Reattach drive cable and return spring

to the idler arm assembly, then reat- tach drive cable to anchor.

11.Reattach drive cover with screws previ- ously removed.

12.Connect spark plug wire to spark plug.

Low

Hi

ENGINE

Maintenance, repair, or replacement of the emission control devices and systems, which are being done at the customers ex- pense, may be performed by any non-road engine repair establishment or individual. Warranty repairs must be performed by an authorized engine manufacturer's service outlet.

ENGINE SPEED

Your engine speed has been factory set. Do not attempt to increase engine speed or it may result in personal injury. If you believe that the engine is running too fast or too slow, take your lawn mower to a Sears or other qualified service center for repair and adjustment.

CARBURETOR

Your carburetor is not adjustable. If your engine does not operate properly due to sus- pected carburetor problems, take your lawn mower to a Sears or other qualified service center for repair and/or adjustment.

17

Image 17
Contents Crrftsmiin Sears, Roebuck and Co., Hoffman Estates, IL Year Full Warranty on Craftsman Lawn MowerALook AwarningII. Slope Operation General OperationDo not III. ChildrenNGK BPR6ES API SG-SL SAELawn Mower Performance Lawn Mower MaintenanceTo Install Attachments HOW to SET UP Your Lawn MowerTo Remove Lawn Mower from To Unfold HandleKnow Your Lawn Mower Meets Cpsc Safety RequirementsTo Adjust Cutting Height Drive Control AdjustmentEngine Speed Engine Zone ControlFor Side Discharging Side DischargingFor Rear Bagging ADD Gasoline Before Starting EngineADD OIL To Stop EngineMulching Mowing Tips OFFMowing Tips Spray lubricant See Engine in Maintenance section Lubrication ChartGeneral Recommendations Before Each USETires Lawn MowerDrive Wheels Blade CareAIR Filter To Clean AIR FilterTo Change Engine OIL Clean Under Drive Cover CleaningMuffler Spark PlugRear Deflector Lawn Mower To Adjust Cutting HeightTo Remove Drive Belt PivotTo Replace Drive Belt To Adjust HandleEngine CarburetorHandle Lawn MowerFold StorageDoes not start ProblemCause ProblemGarantia Programa de Mantenimiento Reglas de Seguridad Hacer Operacion II. Operacion Sobre LAS CuestasNo Hacer III. NinosNGK Mantenimiento DE LA Segadora Acuerdos de Protecci6n para la Reparaci6nRendimiento DE LA Segadora LA Caja DE Carton Para Remover LA Segadora DEComo Preparar SU Segadora Para Desdoblar EL Mango Para Instalar LOS AccesoriosCumple CON LOS Requisitos DE Seguridad DE LA Cpsc Familiaricese CON SU SegadoraDEL Motor SU SegadoraLA Segadora DEL MandoPara Descarga Lateral Segadoras CON Descarga LateralPara Ensacamiento Trasero Antes DE Hacer Arrancar EL AbiertoMotor Agregue Aceite ImportantePara Hacer Arrancar EL Motor Para Parar EL MotorConsejos Para Segar Consejos Para Segar Y AcolcharAntes DE Cada USO Recomendaciones GeneralesTabla DE Lubricacion @BisagraRuedas DE Impulsion LlantasRecogedor DE Cesped Caja DE EngranajesFiltro DE Aire MotorPara Cambiar EL Aceite DEL Motor Limpieza BujjaLimpie Debajo DE LA Cubierta DE LA ImpulsionPara Remover LA Correa DE IMPUL- Sion Segadora Para Ajustar LA Altura DE CortePara Ajustar EL Mango Doblar Hacia Adelante MangoPara AlmacenarCausa ProblemaCorreccion No arrancaProblema Craftsman Rotary Lawn MOWER- Model Number 917.371810 Craftsman Rotary Lawn Mower - Model Number32jll 169911 Bearing Ball Wheel Craftsman Rotary Lawn Mower Model NumberKEY Part Description Service Notes Honda 4-CYCLE Engine Model Number GCV160-AS3A Labels KEY Part NO, NO, Description Flywheel Recoil Starter KEY Part NO, NO. Description Piston Connecting ROD J Cylinder Barrel KEY Part NO, NO, Description Honda 4-CYCLE EngineYour Home

917.37181 specifications

The Craftsman 917.37181 is a high-performance riding lawn mower designed for both residential and commercial use. This versatile machine combines power, precision, and user-friendly features, making it a worthy addition to any outdoor maintenance arsenal. Its robust build quality and innovative technologies ensure efficient cutting, reliable operation, and ease of use, appealing to both novice and seasoned lawn care enthusiasts.

One of the standout features of the Craftsman 917.37181 is its powerful engine. It is equipped with a dependable 19 horsepower Honda engine that provides ample power for tackling tough mowing conditions. The engine’s performance is complemented by its electric start system, which allows for effortless ignition with the turn of a key, eliminating the hassle associated with traditional pull-string models. This feature enhances user convenience, particularly in cold weather or when faced with challenging terrain.

The mower is designed with a 42-inch cutting deck, which strikes a perfect balance between maneuverability and cutting efficiency. This width allows it to easily navigate through narrow pathways while still covering a significant mowing area. The cutting height is adjustable, with several positions available, enabling users to customize their mowing experience based on grass type or weather conditions. This flexibility ensures a clean, even cut every time.

Another noteworthy characteristic of the Craftsman 917.37181 is its innovative transmission system. The hydrostatic transmission provides smooth and seamless speed control, allowing users to operate the mower easily without constant gear shifting. This results in a more enjoyable mowing experience, particularly over uneven or sloped terrain.

Ergonomics have also been prioritized in the design of this riding mower. The spacious, high-back seat offers excellent support, allowing users to remain comfortable during prolonged mowing sessions. Additionally, the mower features convenient mid-back support and accessible controls, making it simple for anyone to operate.

In terms of maintenance, the Craftsman 917.37181 is designed for ease of care. The deck features a washout port that allows for quick cleaning after use, helping to prolong the life of the mower and maintain its performance. The fuel tank is also conveniently placed for easy refueling, ensuring that users can spend more time mowing and less time on maintenance tasks.

Overall, the Craftsman 917.37181 stands out as an exceptional riding lawn mower that combines power, versatility, and user-friendly features. Whether for residential lawns or commercial properties, this model offers reliable performance, ensuring a well-manicured lawn with minimal effort. Its robust design and advanced technologies make it a valuable investment for anyone looking to enhance their lawn care routine.