Craftsman 917.289470 manual To Move Forward and Backward, To Adjust Gauge Wheels, To Operate Mower

Page 16

TO MOVE FORWARD AND BACKWARD

The direction and speed of movement is controlled by the forward and reverse drive pedals.

I. Start tractor and release parking brake.

2Slowly depress forward(K) or reverse(L) drive pedal to begin movemenL Ground speed increases the further down the pedal is depressed,,

TO USE CRUISE CONTROL

The cruise control feature can be used for forward travel onlyo

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

• With forward drive pedal depressed to desired speed, pull cruise control lever

(J)up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal, tap on forward drive pedal or push the cruise control lever down.

TO ADJUST MOWER CUTTING HEIGHT

The position of the attachment lift lever (A) determines the cutting height.

•Put attachment lift lever in desired cutting height slot.

•Slide pointer tab (T) to desired cutting height as a reminder for nexttime you mow.

The cutting height range is approximately

I" to 4". The heights are measured from the ground to the blade tip with the engine not run- ning. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to ap- proximately 2-1/2" during the cool season and to over 3" during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6" in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck

in proper position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

1.Adjust mower to desired cutting height (See "TO ADJUST MOWER CUTTING HEIGHT' in this section of manual).

2.With mower in desired height of cut posi- tion, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten

securely°

3_ Repeat for all, installing gauge wheel in same adjustment hole.

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting offwhen operating your equipment on rough, rolling terrain or hills.

1.Select desired height of cut with attach_ merit lift lever.

2.Start mower blades by engaging attach- ment clutch control.

!6

Page 15 Page 17
Image 16
Page 15 Page 17
Contents GA E Tracto Craftsman Full Warranty TWO Years on Riding Equipment Sears, Roebuck and Co., Hoffman Estates, ILGeneral Operation Service II!, ChildrenIV, Towing Safe Handling of GasolineGeneralservice AndtightensecurelyProduct Repair Protection411111 To Check Battery To Remove Tractor from Carton Unpack CartonSET Parking Brake Lever and Lower Attachment Lift Lever ADJ UST S EATTo Front of Mower Turn Steering Wheel Left and Position MowerSlide Mower Under Tractor Install ANTI-SWAY BAR S If Equipped ANTI-SWAY BAR SAttach Mower Side Suspension Arms a to Chassis Attach Rear Lift Links CInstall Belt on Engine Clutch Pulley M Mower Drive Belt InstallationAttach Front Link E Replace Mower Blade Drive BeltCheck Deck Levelness ChecklistCheck Brake System @@@@ Fire indicates a hazard which, if not avoidedAttachment Clutch Switch Service Reminder / Hour MeterKnow Your Tractor TractorHOW to USE Your Tractor Engine To SET Parking Brake StoppingMower Blades To USE Throttle Control D Ground DriveTo Move Forward and Backward To Adjust Gauge WheelsTo Operate Mower Reverse Operation System ROS To Stop Mower BladesMents Reserve Fuel Valve Operation Before Starting the Engine Check Engine OIL LevelTo Start Engine Automatic Transmission Warm UP Purge TransmissionMowing TiPS Maintenance Schedule Lubrication ChartBfore Every General RecommendationsTires Blade RemovalTransaxlemaintenance Transaxle Pump FluidBelts Engine LubricationMuffler AIR FilterIN-LINE Fuel Filter Movable parts CleaningDeck Washoutport Adjustments To Install MowerFRONTTO-BACK Adjustment Precision SIDE-TO-SIDE AdjustmentTo Level Mower Belt Installation To Replace Mower Drive BeltMower Drive Belt Removal To Replace Motion Drive BeltTo Check Brake Front Wheel TOE-IN/CAMBERTo Start Engine with a Weak BAT- Tery To Attach Jumper CablesReplacing Battery To Adjust Throttle Control CableInterlocks and Relays To Remove Hood and GrillBattery Fuel SystemEngine OIL CylindersAll wiring Hard to startEngine will not turn over Air filterCause ProblemCorrection Correction ITO ILlt ==I DOS Anos Para EL Equipo Tractor Funcionamiento General Ii. Funcionamiento EN PendientesIII, Nlf4OS IV. RemolqueSERVIClO Manipulacion Segura DE LA GasolinaPage Especificaciones DEL Producto RESPONSABtLIDADES DEL ClienteAcuerdos DE Proteccion Para LA Reparacion MY-HOMESogodora Herramientas ParaEL Montaje Instale LA SegadoraUbique LA Cortadora DE C#SPED Deslice LA Cortadora DE Cesped Debajo DEL TractorSI LA TIENE, Instale LA Barra Antibalanceo S Instale LOS Eslabones DE LEVAN- Tamiento Traseros CInstale LA Correa EN LA Polea DEL Embrague DEL Motor M Reemplazar LA Correa DE LA CuchillaRevision DE LA Nivelacion DEL CON Junto REVIS16N DE I.A Presion DE LAS LlantasLista DE Revisin @@@ Istema DE Funcionamiento Haoia Palanca DE Mando CruceroPedal DE Marcha Adelante Pedal DE Marcha AtrasParada Cuchillas DE LA Segadora MotorPara Usar EL Control DE LA Aceler Impulsion DE RecorridoLA Segadora Utilizar EL Mando CruceroDoras Segadora Funcionamiento AtrasTransmisi6n Desenganchada Remolque DE Carretillas O Otros AccesoriosEL Motor MECAI,IISMO DE Aviso DE SERVICiOLina DE Reserva Arranque CON Tiempo Templado 50F/10C V MAS Arranque CON Tiempo FRO 50/i00 YMenos AutomaticaConsejos Para Segar Mantenimiento Caduso e Antes DE Cada USOCada C,DA Tabla LubricacionLlantas VERIF1EZ Sistema Presencia OperadorCuidado DE LA Cuchilla Remocion DE LA CuchillaNivel DEL Fluido DE LA Bomba DEL Transeje MotorLimpieza DE LA Rejilla DE Aire Limpieza DE LA Entrada DE AIRE/AREAS DE EnfriamentoSilenciador BujjasPuerto DE Lavado DE LA Cubierta LimpiezaPuerto de ClaSPED Para Desmontar LA Cortadora DEPara Instalar LA Segadora Lado Ajuste DE Delante a AtrasCuidado Para Reemplazar LA Correa DE LA CUCH1LLA DE LA Segadora Montaje DE LA Correa DE LA SegadoraPara Cambiar LA Correa DE Impulsion DE Movimiento Desmontaje DE LA CorreaVerifique EL Freno IMPRESlON / Inclinacion DE LAS Ruedas DelanterasPara Remover LAS Ruedas Para Hacer Reparaciones LlaveCuadradarueda .==== traserasolarnenteReemplazar LA Bateria Para Remover EL Conjunto DEL Capo Y DEL EnrejadoPara Cambiar LA Bombilla DE LA LUZ Delantera Entrecierre Y RelisMotor Sistema DE Combustible Importante Es important evitar que se forAceite DEL Motor CilindrosNo arranca Dtficll deEl motor no El motorIdentificacion DE Problemas IDENTIFICACI6N DE Problemas Page Gtl Www,sears.corn Wwwsears,ca Www,sears,com800827-6655 usA Canada 800.LE.FOYER Mc

917.28947, 917.289470 specifications

The Craftsman 917.28947 and 917.289470 are robust lawn tractors designed for homeowners seeking durability, performance, and comfort in their yard care equipment. These models stand out in the Craftsman line due to their exceptional features, advanced technologies, and user-friendly characteristics.

At the core of both models is a powerful engine, typically a 19 HP or higher, ready to tackle various mowing conditions. The engine is combined with a smooth-running automatic transmission that facilitates easy operation, allowing the driver to focus on the task without worrying about shifting gears. This feature makes mowing large lawns or navigating through obstacles much simpler.

One of the most notable characteristics of the Craftsman 917.28947 and 917.289470 is their 42-inch cutting deck. This size is ideal for providing a quick yet efficient cut, capable of maneuvering in tighter spaces while still covering more ground than smaller decks. The cutting height can be easily adjusted to meet the needs of different types of grass and preferred lawn styles. This adaptability is part of what makes these models particularly appealing to a diverse range of users.

Incorporating advanced technologies, these lawn tractors often feature an ergonomic design, including a plush seat with back support that provides comfort during prolonged use. The easy-to-read dashboard displays critical information such as fuel level, speed, and battery status, allowing users to monitor their operation effectively.

Additionally, both models come equipped with essential safety features such as a safety switch that prevents the engine from starting when the operator is not seated. This attention to safety ensures peace of mind during operation, especially for those who may have children or pets around while mowing.

In terms of maintenance, the Craftsman 917.28947 and 917.289470 include features designed to make care manageable. The accessible design allows for easy cleaning and part replacement when necessary, ensuring that the tractors remain in top condition throughout their lifespan.

Overall, the Craftsman 917.28947 and 917.289470 represent a great combination of power, efficiency, and comfort, making them excellent choices for homeowners looking to maintain their lawns with ease and reliability. Whether tackling a small yard or a larger landscape, these lawn tractors are equipped to deliver effective performance season after season.
Top Page Image Contents