Craftsman 917.375631 To Replace Drive Belt, To Adjust Handle, Squeeze To Adjust, Carburetor

Page 15

TO REPLACE DRIVE BELT

1.Place new drive belt in engine pulley and belt retainer of debris shield.

2.Route the other end of the new drive belt through hole in housing.

3.Reinstall debris shield.

4. Reinstall blade.

5.Return mower to upright position.

6.Push down on arm, install new belt on

gearcase pulley. Release arm slowly. NOTE: Always use factory approved belt to assure proper fit and long life.

7.Reinstall drive cover.

TO ADJUST HANDLE

The handle can be mounted in a high or

low position. The mounting holes in the bottom of lower handle are off center for

raising or lowering the handle.

1.Remove upper handle and all wire tie(s) securing cable(s) to lower handle.

2.Remove hairpin cotters from lower handle bracket mounting pin.

3.Squeeze lower handle in to remove it

from mounting pins.

4.Turn lower handle over to raise or lower handle.

5.Squeeze lower handle in and position holes onto mounting pins on bracket.

6.Reassemble upper handle and all parts removed from lower handle.

SQUEEZE

TO ADJUST

Lower handle

Mounting pin

Handle

Hairpin cotter

J

\

\

\

Lower handle

ROTATE

ENGINE

ENGINE SPEED

Your engine speed has been factory set. Do not attempt to increase engine speed or it may result in personal injury. If you believe that engine is running too fast or too slow, take your mower to a Sears or other qualified service center for repair and adjustment.

CARBURETOR

Your carburetor is not adjustable. If your engine does not operate properly due to sus- pected carburetor problems, take your lawn mower to a Sears or other qualified service center for repair and/or adjustment.

IMPORTANT: Never tamperwith the engine governor, which is factory set for proper en- gine speed. Overspeeding the engine above the factory high speed setting can be danger-

ous. If you think the engine-governed high speed needs adjusting, contact a Sears or other qualified service center, which has proper equipment and experience to make any necessary adjustments.

15

Image 15
Contents Craftsman Limited 2-YEAR Warranty on Craftsman Power Mower Your Safety InvolvedBecome IV. Safe Handling of Gasoline Do notRJ19HX API SG-SL SAERepair Protection Agreements To Unfold Handle HOW to SET UP Your MowerTo Install Attachments To Remove Mower from CartonKnow Your Lawn Mower Meets Cpsc Safety RequirementsTo Convert Mower HOW to USE Your Lawn MowerADD Gasoline Before Starting EngineTo Stop Engine ADD OILMulching Mowing Tips Mowing TipsGeneral Recommendations Before Each USELubrication Blade Care TiresDrive Wheels Gear CaseEngine AIR FilterMuffler Lawn Mower To Adjust Cutting Height Rotate Engine Engine Speed To Adjust HandleSqueeze To Adjust To Replace Drive BeltLawn Mower Fuel SystemCylinder ProblemOther Engine OILProblem CauseCorrection Esta Comprometida AlertoOperacion HacerNo Hacer Serie Rendimiento DE LA Segadora Para Instalar LOS Accesorios Para Remover LA Segadora DE LA Caja DE CartonFamiliaricese CON SU Segadora ImportanteCumple CON LOS Requisitos DE Seguridad DE LA Cpsc Para Ajustar LA Altura DE Corte Velocidad DEL MotorPara EL Impulsion Para Convertir LA SegadoraMotor Consejos Para Segar Tabla Antes DE Cada USOCaja DE Engranajes SegadoraLlantas Ruedas DE ImpulsionFiltro DE Aire MotorLimpie Debajo DE LA Cubierta DE LA Impulsion Segadora Para Ajustar LA Altura DE CorteDesviador Trasero Proteccion Contra LA DescargaMotor Velocidad DEL Motor Para Ajustar EL MangoSegadora MangoSistema DE Combustible Solucion ProblemasProblema Causa Correccion Aceite DEL MotorSolucion est dirigido ProblemaRotary Lawn Mower - Model Number CraftsmanCraftsman Rotary Lawn Mower - Model Number PartDescription Craftsman Rotary Lawn Mower - Model Number Retainer 183501 Spring Repair Manuai Briggs & Stratton 4=CYCLE EngineCarburetor Overhaul KIT Carburetor Gasket SETBriggs & Stratton 4-CYCLE Engine J058 Operators ManualEmissions Label Engine Gasket SET 842 S24 668PTO KEY Part DescriptionKEY Part NO. NO. Description Service Notes Service Notes Need More HELP?