Craftsman 917.374361 owner manual Lawn Mower, Drive Wheels

Page 14

LAWN MOWER

Always observe safety rules when per- forming any maintenance.

TIRES

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

DRIVE WHEELS

Check rear drive wheels each time before you mow to be sure they move freely.

The wheels not turning freely means trash,

grass cuttings, etc. are in the drive wheel area and must be cleaned to free drive wheels.

If necessary to clean the drive wheels, be sure to clean both rear wheels.

5.Install the blade bolt with the lock washer and hardened washer into blade adapter and crankshaft.

6.Use block of wood between blade and

lawn mower housing and tighten the blade bolt, turning clockwise.

•The recommended tightening torque is 35-40 ft. Ibs.

IMPORTANT: Blade bolt is heat treated. If bolt needs replacing, replace only with approved bolt shown in the Repair Parts section of this manual.

BLADE CARE

For best results, mower blade must be kept

sharp. Replace a bent or damaged blade. A CAUTION: Use only a replacement

blade approved by the manufacturer of your mower. Using a blade not approved by the manufacturer of your mower is haz- ardous, could damage your mower and void your warranty.

TO REMOVE BLADE

1.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

2.Turn lawn mower on its side. Make sure air filter and carburetor are up.

3.Use a wood block between blade and mower housing to prevent blade from

turning when removing blade bolt. NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

4.Remove blade bolt by turning counter- clockwise.

5.Remove blade and attaching hardware (bolt, lock washer, hardened washer).

6.Remove debris shield.

NOTE: Remove the blade adapter and check the key inside hub of blade adapter. The key must be in good condition to work properly. Replace adapter if damaged.

TO REPLACE BLADE

1.Position blade adapter on engine crank- shaft. Be sure key in adapter and crank-

shaft keyway are aligned; and that drive belt is inside tabs of belt retainer.

2.Install debris shield.

3.Position blade on the blade adapter. IMPORTANT: To ensure proper assembly, center hole in blade must align with star on blade adapter.

4.Be sure the trailing edge of blade (oppo- site sharp edge) is up toward engine.

 

 

Belt

 

retainer

 

Trailing

edge

Blade adapter

 

 

 

Hardened

Debris shield

washer

 

Lockwasher

Blade

Blade

bolt

TO SHARPEN BLADE

NOTE: We do not recommend sharpening

blade - but if you do, be sure blade is bal- anced. An unbalanced blade will cause

eventual damage to mower or engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a

5/8" diameter steel bolt, pin, ora cone bal- ancer. (When using a cone balancer, follow instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

Center hole

5/8" bolt or pin

14Blade

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Craftsman Yearfull Warranty on Craftsman Lawn Mower Your Safety is InvolvedDo not General OperationIV. Safe Handling of Gasoline General Service RJ19HXLawn Mower Maintenance Lawn Mower PerformanceMowing To Remove Mower from CartonTo Unfold Handle PositionTo Assemble Grass Catcher To Prepare BatteryTo Install Attachments Meets Cpsc Safety Requirements Know Your Lawn MowerEngine Speed For Rear Bagging Rear BaggingSide Discharging To Convert MowerBefore Starting Engine Mulching Mowing Tips Mowing TipsLubrication General RecommendationsBefore Each USE Before After EveryLawn Mower Drive WheelsGear Case To Clean AIR FilterGrass Catcher Engine LubricationWater Washout Feature CleaningClean Under Drive Cover MufflerTo Remove Drive Belt To Adjust HandleRear Deflector To Replace Drive BeltEngine Speed CarburetorHandle Fold Forward for Storage Mowing PositionOther BatteryProblem Cause Correction Fuel SystemProblem CauseSears, Roebuck and Co., Hoffman Estates, IL SU Seguridad Esta ComprometidaII. Operacion Sobre LAS Cuestas OperacionIII. Ninos HacerSAE RJ19HXRendimiento DE LA Segadora Mantenimiento DE LA SegadoraComo Preparar SU Segadora Para Remover LA Segadora DE LA Caja DE CartonPara Montar EL Recogedor DE Para Instalar LOS AccesoriosFamiliaricese CON SU Segadora Producto. Aprenda y comprenda sus significadosAjuste DEL Mando Como Usar SU SegadoraControl DE LA IMPULSI6N ATRA.SPARA Bajar Palancahacia EL CORTAC¢SPEDSegadoras CON Descarga Lateral Para Convertir LA SegadoraSegadoras CON Descarga Trasera Para Ensacamiento TraseroAntes DE Hacer Arrancar EL Motor Para Parar EL MotorOnsejos Para Segar Consejos Para Segar Y ACOL- CharRecomendaciones Generales Antes DE Cada USORuedas DE IMPULSI6N SegadoraLlantas Cuidado DE LA CuchillaPara Cambiar EL Aceite DEL Motor Recogedor DE CospedCaja DE Engranajes Filtro DE AireLimpie Debajo DE LA Cubierta DE LA Impulsion LimpiezaDerrubio DEL Agua Desviador Trasero SegadoraLA Altura DE Corte Para Remover Correa DE ImpulsionVelocidad DEL Motor CarburadorAceite DEL Motor Problema CausaMotor CilindroCausa CorreccionCraftsman Rotary Lawn Mower - Model Number 917.37436t Description CraftsmanKEY Part 1833 Craftsman Rotary Lawn Mower - Model Number 917o37436t KEY Part DescriptionBriggs & Stratton 4-CYCLE Engine Model Number 128T05-1268=B1 564 883 Briggs & Stratton Cycle Engine Briggs & STRATTON4-CYCLE Engine Service Notes Service Notes Serifs

917.374361 specifications

The Craftsman 917.374361 is a powerful and versatile riding lawn mower that has gained a loyal following among homeowners and landscapers alike. Known for its robust construction and efficient performance, this model boasts several features that cater to a variety of lawn care needs.

At the heart of the Craftsman 917.374361 is a reliable 17.5 horsepower, Briggs & Stratton engine. This engine is designed to deliver strong, consistent power, making it capable of tackling even the toughest mowing tasks. The automatic transmission enables smooth operation, allowing users to easily adjust their speed according to the terrain and conditions. With a cutting width of 42 inches, this mower can efficiently cover large areas, reducing the time spent on lawn maintenance.

One of the standout features of the Craftsman 917.374361 is its adjustable cutting height. With multiple positions to choose from, users can customize the grass height to suit their lawn's specific needs. This capability helps ensure a healthy lawn, as it promotes better growth and reduces the likelihood of scalping or damaging the grass.

The mower also incorporates a tight turning radius, which enhances maneuverability around flower beds, trees, and other obstacles in the yard. This feature is particularly beneficial for landscaping projects where precision is key. Additionally, the front axle design allows for a smooth ride, contributing to overall comfort during operation.

Another noteworthy characteristic of the Craftsman 917.374361 is its durable construction. Built with high-quality materials, this mower is designed to withstand the rigors of regular use. The deck is manufactured from heavy-duty steel, providing protection against wear and tear over time.

In terms of maintenance, the Craftsman 917.374361 is equipped with an easier access design that simplifies tasks such as oil changes and blade replacements. Its user-friendly controls are intuitive, making it accessible for beginners and experienced operators alike.

Overall, the Craftsman 917.374361 combines power, efficiency, and durability, making it a reliable choice for anyone seeking an effective lawn care solution. With its array of features, technologies, and solid performance, this riding lawn mower continues to stand out in the competitive landscaping market. Whether for personal use or commercial applications, it remains a staple for those wanting a well-manicured lawn with minimal effort.
Top Page Image Contents