Craftsman Comprehensive Guide for Lawn Mower 917.271653: Installation and Maintenance Instructions
Page 10

INSTALL MULCHER PLATE

(If previously removed)

1.Raise and hold deflector shield in upright position.

2.Place front of mulcher plate over front of mower deck opening and slide into place, as shown.

3.Hook front latch into hole on front of mower deck.

4.Hook rear latch into hole on back of mower deck.

Mulcher

DeflectorPlate

Latch

jlqHooks

_ILCAUTION: Do not remove deflector shield from mower. Raise and hold shield when attaching mulcher plate and

allow it to rest on plate while in opera- tion.

TO CONVERT TO BAGGING OR

DISCHARGING

Simply remove mulcher plate and store in a safe place. Your mower is now ready for discharging or installation of optional grass catcher accessory.

NOTE: It is not necessary to change blades. The mulcher blades are de-

signed for discharging and bagging also.

CHECK TIRE PRESSURE

The tires on your tractor were overin- flated at the factory for shipping pur- poses. Correct tire pressure is important for best cutting performance.

°Reduce tire pressure to PSI shown in

"PRODUCT SPECIFICATIONS" section of this manual.

CHECK DECK LEVELNESS

For best cutting results, mower housing should be properly leveled. See "TO LEVEL MOWER HOUSING" in the

Service and Adjustments section of this manual.

CHECK FOR PROPER POSITION OF ALL BELTS

See the figures that are shown for replacing motion and mower blade drive belts in the Service and Adjustments section of this manual. Verify that the belts are routed correctly.

CHECK BRAKE SYSTEM

After you learn how to operate your tractor, check to see that the brake is properly adjusted. See "TO ADJUST

BRAKE" in the Service and Adjustments section of this manual.

/CHECKLIST

Before you operate and enjoy your new tractor, we wish to assure that you receive the best performance and satisfaction from this Quality Product.

Please review the following checklist: ,/All assembly instructions have been

completed.

,/No remaining loose parts in carton. ,/Battery is properly prepared and

charged. (Minimum 1 hour at 6 amps). •/ Seat is adjusted comfortably and

tightened securely.

,I All tires are properly inflated. (For shipping purposes, the tires were overinflated at the factory).

,/Be sure mower deck is properly leveled

side-to-side/front-to-rear for best cutting results. (Tires must be properly inflated for leveling).

,/Check mower and drive belts. Be sure they are routed properly around pulleys and inside all belt keepers.

,/Check wiring. See that all connections

are still secure and wires are properly clamped.

While learning how to use your tractor, pay

extra attention to the following important items:

,/Engine oil is at proper level.

,/Fuel tank is filled with fresh, clean, regular unleaded gasoline.

#" Become familiar with all controls - their location and function. Operate them before you start the engine.

,/Be sure brake system is in safe operat- ing condition.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Sears Craftsman Help Line Am 5 pro, Mon- SatLimited Warranty on Craftsman Riding Equipment Limited Warranty on BatteryGeneral Operation I1. Slope OperationMow up and down slopes, not across IV. ServiceDo not Page Customer Responsibilities Product SpecificationsRepair Agreement SAESeat Steering Wheel Hex Bolt Steering3/8-16x Wheel InsertLocknut 1/2-20 17/32 x 1-3/16 x 12 GaugeTo Remove Tractor from Carton Tools Required for AssemblyBefore Removing Tractor from Skid Install Seat Adjust seat before tightening adjustment knobCheck Tire Pressure Install Mulcher PlateTo Convert to Bagging or Discharging Check Deck LevelnessH L Clutch/Brake Indicator Pedal KnowyourtractorTo USE Throttle Control Howto UseyourtractorTo SET Parking Brake To Move Forward and BackwardTo Transport To Operate MowerTo Operate On Hills Towing Carts and Other ATTACH- MentsADD Gasoline Adjustments section of this manualTo Start Engine Mowing Tips Mulching Mowing TipsGeneral Recommendations Lubrication ChartBeforeeachuse SectionTires BatteryBrake Operation Operator Presence SystemBelts EngineEngine Cooling Fins Clean AIR ScreenCleaning MufflerTo Remove Mower Service or AdjustmentsTo Install Mower Both SidesFRONT-TO-BACK Adjustment To Level Mower HousingSIDE-TO-SIDE Adjustment To Replace Mower Blade Drive BeltTo Replace Motion Drive Belt To Adjust BrakeBelt Removal Front Wheel TOE-IN/CAMBER Transaxle Gear Shift Lever Neutral AdjustmentTo Adjust Steering Wheel Alignment To Remove Wheel for RepairsTo Replace Headlight Bulb Replacing BatteryTo Remove Hood and Grill Assembly Interlocks and RelaysEngine To Adjust Throttle Control CableTo Adjust Carburetor Holes a ThrottleCylinders Fuel SystemEngineoil OtherCause Troubleshooting ChartProblem CorrectionTroubleshooting Chart Problem Cause CorreconUnder Problem Cause CorrectionLevel Improper blades usedTractor - Model Number Schematic Electrical Tractor - Model Number Electrical KEY Part DescriptionTractor - Model Number Chassis and Enclosures Tractor -- Model Number 917.271653 Chassisand Enclosures Tractor - Model Number Ground Drive Tractor - Model NUM BER Tractor - Model Number 917.271653 Steering Assembly Tractor - Model Number Steering Assembly 160367Spark Arrester Tractor - Model NumberEngine Optional Equipment KEY Part2O2O Tractor - Model Number Lift AssemblyKEY Part NO. NO. Description Tractor --MODEL Number Seat Assembly 14 72050412 Bolt Rdhd Sht Nk 1/4-20x1-1/2Tractor - Model Number Decals Tractor - Model Number Mower Deck Tractor --MODEL Number Mower Deck 721406145950 Part KEY Description 757 883 Label KIT Ownersmanual 127 186 1421 202 562 267 711 467971 I601240 176 404@ 276 11275803 LABEL-EMISSIONSEngine Gasket SET Carburetor Overhaul KITValve Gasket SET 121A Carburetor Overhaul KITAir Cleaner 729 Page Suggested Guide for Sighting Slopes for Safe Operation Anytime, day or night A. and Canada
Top Page Image Contents