Craftsman 917.25801 owner manual To Start Engine, ADD Gasoline

Page 15

ADD GASOLINE

•Fill fuel tank to bottom of tank filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Pumhase fuel in quantities that can be used within 30 days to assure fuel freshness.

_1=CAUTION: Wipe off any spilled oil or

fuel Do not store, spill or use gasoline near an open flame.

IMPORTANT: When operating in temperatures below 32°F(0°C), use fresh, clean winter grade gasoline to help insure good cold weather staring.

_1_ CAUTION: Alcohol blended fuels

(called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE

When staring the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

1.Sit on seat in operating position, depress clutch/brake pedal and set parking brake.

2.Place gear shift lever in neutral (N) position.

3.Move attachment clutch to disen- gaged position.

4.Move throttle control to choke position. NOTE: Before starting, read the warm and cold starting procedures below.

5.Insert key into Ignition and tum key clockwise to start position and release key as soon as engine starts. Do not run starer continuously for more than fifteen seconds par minute. If the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try

again. If engine still does not staR, move the throttle control back to the

choke position and retry.

WARM WEATHER STARTING (50 ° F and above)

6. When engine stars, move the throttle control to the fast position.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING ( 50 ° F and

below)

6.When engine starts, allow engine to run with the throttle control in the

choke position until the engine runs roughly, then move throttle control to fast position. This may require an engine warm-up period from several seconds to several minutes, depend-

ing on the temperature.

•The attachments can also be used

during the engine warm-up period.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. (See 'q'OADJUST CARBURETOR" in the

Service and Adjustments section of this manual).

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents ICRRFTSMRW Limited Warranty on Craftsman Riding Equipment General Operation II. Slope OperationIII. Children IV. ServicePage RC12YC Repair AgreementCustomer Responsibilities SAESteering Wheel Tools Required for Assembly Assemble Extension Shaft and BootBefore Removing Tractor from Skid Install Seat Check Tire Pressure CheckdecklevelnessCheck for Proper Position of Allbelts Check Brake SystemENG,N=ONENG,NEOFFO,LPREL,GHTSONORE Ovit Amedcan National Standards Institute Know Your TractorHOW to USE Your Tractor To SET Parking Brake StoppingEngine To Operate on Hills To TransportTowing Carts and Other ATTACH- Ments To Operate MowerADD Gasoline To Start EngineMowing Tips Lubrication Chart General RecommendationsBefore Each USE Operator Presence System BatteryBrake Operation TiresEngine To Change Engine OILBelts To Service PRE-CLEANER Clean AIR ScreenEngine Cooling RNS Cleaning Service or AdjustmentsTo Remove Mower FRONT-TO-BACK Adjustment To Level Mower HousingTo Install Mower SIDE-TO-SIDE AdjustmentBelt Belt InstallationTo Adjust Brake To Replace Mower Blade DriveTo Start Engine with a Weak To Replace Fuse Replacing BatteryTo Adjust Carburetor Preuminary SettingAcceleration Test Other To Clean Battery and TermiEngine OIL CylindersTroubleshooting Chart Problem CauseCorrection Problem Cause Correction TroubleshootingchartCorrection Troubleshooting ChartProblem CauseEI 4---E Tractor Model Number SchematicTractor Model Number Electrical KEY Part NO. NO. Description Tractor Model Number ElectricalTractor Model Number 917.258010 Chassisand Enclosures KEY Part Description Tractor Model Number 917.258010 Chassis and EnclosuresTRACTOR- Model Number Ground Drive Dng#5133-75 Tractor Model Number Ground DriveTractor Model Number Steering Steering Tractor Model NumberOptional Equipment Tractor Model Number EngineKEY Part Description Tractor Model Number EngineTractor Model Number Seatassembly Wheels Tires Tractor Model Number DecalsTractor Model Number Liftassembly Tractor Model Number Lift Assembly Tractor Model Number Mower Deck Mandrel AssemblyIncludes Tractor Model Number Dana TRANSAXLE-MODEL Number D4360-139 061 Tractor Model Number Dana TRANSAXLE-MODEL Number D4360-13913J Requires Specialtools To INSTALL. see RepairOwnersmanual Label KITLABEL-EMISSIONS 977A Carburetor Gasket SET Carburetor Gasket SET Overhaul KITEngine Gasket SET 121A Carburetor Overhaul KITLinderAssembly Nut Brush Retainer Page Page Page Suggested Guide for Sighting Slopes for Safe Operation Part
Top Page Image Contents