Craftsman 900.37051 manual To Stop Mower, Mowing Procedure

Page 5

TO STOP MOWER

To stop mower fully release your grip on the operator presence control switch.

ATTACHING EXTENSION

CORD TO MOWER

DO NOT connect the extension cord to power source until you have finished reading this manual and you are ready to start mowing. Reod the Polarized Plug

se<:tionon poge ,5 before plugging the extension cord into the switch housing as

shown in figure below.

To raise or lower the cutting height, rest the palm of your hand on the palm rest and with your fingers, squeeze upward on the finger grip and hold.

pointer _-_ Scale

out so that you can grab it with your other hand. Pull the lever back to turn the unit

on and hold it against the mower handle to keep it running. To turn the mower off, just release the lever. The spring loaded

"SNAP ACTION" lever will quickly turn the mower off.

WARNING:

For your own safety DO NOT use this mower without either the gresscatcher or mulch insert in operating position.

Do not operate the lawnmower if the rear door is not under spring tension. Take your mower to the nearest Sears Service Center for repair,

]

1.The extension cord must be polarized

and will only plug in one way. Orient the wide slot with tile wide blade in the

switch housing and plug in.

2.Make a )oop in the extension cord.

3.Push the loop up through the hole in the switch housing.

4.Place the loop over the strain relief tab on the switch housing. Pull the extension cord so the loop draws down around the strain relief tab as shown in the detail. Double check to see that you did nol loosen the extension cord plug.

TO ADJUST CUTTING HEIGHT

Before making any adjustments, turn off, unplug mower and wait for blade to stop rotating.

Use the Height Adjustment Control to

raise deck for high cut and lower deck for low cut.

Adjust cutting height to suit your requirements. Medium position is best for most lawns

While holding the finger grip up you can raise or lower the cutting height. The

mulcher has eight blade height adjustment positions. Refer to the scale and pointer at the front of the mower. The pointer will give you the height setting for cutting your lawn. This setting can be a reference for the next time you want to cut your lawn at the same height. When you have the mower at the height you like, simply release the finger grip to lock the height in.

NOTE: To ensure that the deck is securely rocked in one of the eight positions, press down on the palm rest after releasing the

finger grip.

OPERATOR PRESENCE

CONTROL SWITCH

CAUTION: Federal regulations require an

Operator Presence Control Switch to be installed on lawn mowers in order to minimize the risk of blade contact injury.

DO NOT under any circumstances attempt to defeat the function of this switch.

Ramem-berthat the blade always turns

when the motor +s running.

The Operator Presence Control Switch is a lever that you pull back to start and run the mower. The switch requires you to be

positioned behind the mower handle for

mower operation.

To operate the switch, insert your finger

into the opening (A) and push the lever

SAFETY SHIELD & REAR DOOR

The safety shield is designed to minimize

the throwing of stones or other objects by the mower blade backward from under the

mower deck. The shield, along with the rear door, minimizes the possibility of accidental foot contact with the blade. DO

NOT operate mower without the safety shield and rear door in place.

Handle

Pocket

M_lch

MOWING PROCEDURE

Inspect area where mower is to be used and remove all stones, sticks, wire, bones, and other debris which might be thrown by the rotating blades.

Place most of the extension cord close

to the electrical outlet, out of the path of the mower.

CAUTION: Do not plug extension cord

into receptacle outlet while standing in water or when hands are wet.

Begin mowing in the area closest to the outlet. Always mow forward in a back and forth pattern across the lawn. Keep the cord on the cut portion of the lawn.

MOWING TIPS

Mow across the face of slopes, never up-and-down. Exercise extreme caution when changing direction on slopes. Do not mow excessively steep slopes. Always maintain good footing.

Release switch to turn mower "OFF" when crossing any graveled area (stones can be thrown by the blade).

Set mower at highest cutting height when mowing in rough ground or in tall weeds.

From time to time turn off mower and

9

Image 5
Contents CRAFTSMAN,+ Preparation Limited TWO Year Warranty on Craftsman Power MowerTraining OperationCarton Contents Maintenance and StorageDouble Insulation Polarized PlugTo Install Grasscatcher Grasscatcher AssemblyMeets Cpsc Safety Requirements To Unfold HandleTo Stop Mower Mowing ProcedureMulching To Remove BladeBlade Care Product SpecificationsGeneral Recommendations LubricationCause ProblemCRAFTSMANLAWNMOWER- MODELNUMBER900.370510 Parts ListDoble Aislamiento PreparacionMantenimiento Y Almacenaje Oordones DE ExtensionParasacarlapodadora Calibre Minimo ParaextensionesDE SU Caja Conserve Estas InstfiuccionesAjuste DE Altura DE Corte Recomendaciones Para Podado CON Recorte Cuadro DE Responsabilidades DEL Usuario Evite LA Corrosion Cuidado DE LA CuchillaLimpieza Deflector TraseroMY-HOME1.800-469-4663

900.37051 specifications

The Craftsman 900.37051 is a versatile and reliable tool in the Craftsman line, known for its robust construction and user-friendly features. Designed with the needs of both professionals and DIY enthusiasts in mind, this product offers a blend of efficiency, durability, and performance.

One of the standout features of the Craftsman 900.37051 is its powerful motor, which allows for quick and efficient operation. The motor delivers consistent power, enabling users to tackle a wide range of tasks with ease, from household repairs to advanced woodworking. This reliability makes it an essential tool for any workshop.

The tool is equipped with an ergonomic design, ensuring comfort during prolonged use. The soft-grip handle minimizes fatigue, providing better control and reducing the risk of slipping. This feature is especially important for users who may spend extended periods using the tool, as it significantly enhances usability and safety.

Another notable characteristic of the Craftsman 900.37051 is its versatility. This tool comes with multiple attachments and settings, allowing it to perform various functions. Whether it's sanding, polishing, or cutting, this tool easily adapts to the task at hand, making it suitable for a wide range of projects.

In terms of technology, the Craftsman 900.37051 incorporates advanced components that enhance its functionality. The tool features a quick-change system, which allows users to swap out attachments swiftly, saving time and increasing productivity. This innovation is particularly beneficial in fast-paced work environments where efficiency is crucial.

Safety is also a priority in the design of the Craftsman 900.37051. The tool includes safety features such as a safeguard shield and a well-placed lock-off switch, preventing accidental activation. These features provide peace of mind while using the tool, allowing users to focus on their work without worrying about potential hazards.

Overall, the Craftsman 900.37051 is a well-rounded tool that combines power, comfort, versatility, and safety. Whether for professional use or personal projects, it stands out as a valuable addition to any toolkit. With its user-centric design and robust performance, this tool is sure to meet the demands of any crafting or repair job, making it a trusted choice for those who seek quality and reliability in their tools.