Craftsman 944.602951 owner manual To Roll Tractor OFF Skid See Operation

Page 7

ASSEMBLY

Connect BLACK groundingcable to negative (-) terminal with remaining hex bolt and keps nut. Tighten securely.

 

 

DISCARD TERMINAL

 

 

PROTECTIVE CAPS

 

 

KEPS

TERMINAL

!i

HEX BOLT

NU_

POSITIVE (BED)

NEGATIVE (BLACK)

CABLE

CABLE

 

RG. 2

SEAT PAN

 

FIG. 3

NSTALL SEAT (See Fig. 4)

\d just seat before tightening adjustment knob.

Remove adjustment knob and flatwasher securing seat to cardboard packing and set aside for assembly of seat to tractor.

Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard. Place seat on seat pan so head of the shoulder boltsare positioned over large slotted holes in pan.

Push down on seat to engage shoulder boltsin slots and pull seat towards rear of tractor.

Pivot seat and pen forward and assemble adjustment knob end flat washer loosely. Do not tighten.

Lower seat into operating position and sit on seat.

Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

Get off seat without moving its adjusted position. Raise seat and tighten adjustment knob securely.

SEAT

SEAT

PAN_

SHOULDER

BOLTS

FLAT WASHER

ADJUSTMENTm W

KNOB

FIG. 4

NOTE: You may now roll or ddve your tractor off the skid.

Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Operation

section page 10 for location and function of controls)

•Press liftlever plunger and raise attachment liftlever to its highest position.

•Release parkingbrake bydepressing clutctVorakepedal.

•Place freewheel control in freewheeling position to disengage transmission (See "TO TRANSPOR'I" inthe

Operation section of this manual).

•Roll tractor forward off skid.

•Remove banding holding deflector shield up against tractor.

TO DRIVE TRACTOR OFF SKID (See Opera- tion section page 10 for location and function

of controls)

_WARNING: Before starting, read, understand and follow

all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in

front of tractor is clear of other people and objects.

•Be sure all the above assembly steps have been completed.

•Check engine oil level and fillfuel tank with gasoline.

•Place freewheel control in "transmission engaged" posi- tion.

•Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

•Place motion control lever in neutral (N) position.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Jcraftsman J Do not IV. Service4Rk Safe Operation Practices for Ride-On Mowers a II. Slope OperationTable of Contents Customer Responsibilities Product SpecificationsMaintenance Agreement Full ONE 1 Year Warranty on Battery@@ BaRery Steering Wheel SeatKeys Slope Sheet Unpack Carton Tools Required for AssemblyTo Removetractor from Carton Before Removing Tractor from SkidSection page 10 for location and function of controls To Roll Tractor OFF Skid See OperationCheck for Proper Position of ALL Belts ChecklistInstall Mulchefi Plate To Convert to Bagging or DischargingReverse Neutral High LOW Parking Brake Clutch Engaged BatteryForward SlowKnow Your Tractor OperationTo USE THROI-rLE Control See Fig HOW to USE Your TractorTo Adjust Mower CUI-rlNG Height See FigTo Operate on Hills To Adjust Gauge Wheels See FigTowing Carts and Other Attachments Purge Transmission Before Starting the EngineADD Gasoline To Start Engine See FigMulching Mowing Tips Mowing TipsBefore Each USE General RecommendationsBrake Operation BatteryTractor To Sharpen Blade See FigTransaxle Cooling EngineAIR Filter See Fig IN-LINE Fuel Filter See FigSpark Plugs To Level Mower Housing To Install Mower See FigTo Remove Mower See Fig UFT Link Belt InstallationSee Fig Dmandrel Both Front Links Must be Equal in LengthFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment ISee FigFront Wheel Camber To Remove Hood and Grill Assembly See FigTo Start Engine with a Weak BATrERY See Fig To Replace Headlight BulbSpeed Bracket To Adjust Carburetor See FigIdle Speed Adjusting Acceleration TestEngine OIL Fuel SystemCylinders Cause ProblemCorrection Cause ProblemTractor - Model Number SchematicElectrical Tractor - Model NumberKEY Part NO. NO.DESCRIPTION ElectricalChassis and Enclosures KEY Part Description Chassis and EnclosuresRepairparts KEY Part Description NO. no DriveSteering Assembly 72140618 Seat Assembly Wheels & Tires DecalsKEY Part Optional Equipment Engine20..,., 161718 1520 Mower LiftMower Deck KEY Hydro Gear Transaxle Model Number KEY Part NO. no Hvdro Gear Transaxle Model Number 314,.0510Crankcasei CARTER-MOTEUR Kohler Engine Model Number CV492, Type NumberDescription Cylinder HEAD/VALVE/BREATHER Crankcase KEY Part NO. noKEY Part NO. NO.DESCRIPTION IGNITION/ELECTRICAL I Electriqueallumage Tractor - Model Number 944,602951Not Illustrated NotillustratedKEY Part NO. no Starting System Engine Controls OIL PAN/LUBRICATION KEY Part NO. no Startingsystem Engine Controls KEY Part NO. NO.DESCRIPTIONFuel System Fuel DE LE Systime Kohler Engine Model Number CV492, Type Number CrankshaftNot Illustrated Description Fuelsystem Crankshaft KEY Part NO. noExhaust Service Notes Service Notes Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationMY-HOME
Top Page Image Contents