Craftsman 79964 manual Gasand OIL FILL-UP, To Empty BAG, Oil

Page 10

If necessary, use the tamper plug provided to push

material into the chipper chute. See figure 8. NEVER PLACE HANDS INSIDE CHIPPER CHUTE. PIace

tamper plug inside chipper chute when not in use to deaden the sound.

FIGURE 11.

IMPORTANT: There is a flail screen located inside the housing in the discharge area. If the flail screen becomes clogged, remove and clean as instructed in the Service and Adjustment section on page 14.

For best performance, it is important to keep the

chipper blades sharp. If the composition of the material being discharged changes (becomes stringy, etc.) or if the rate at which the material is discharged slows down considerably, it is likely that the chipper

blades are dutl and need to be sharpened or replaced. Refer to Service and Adjustments sections.

TO EMPTY BAG

Open the large zipper on the bag to empty the bag. See figure 12. Be certain the zipper is closed when operating the unit.

FIGURE 12.

GASAND OIL FILL-UP

OIL

Only use high quality detergent oil rated with API service classification SF, SG or SH. Select the oil's viscosity grade according to your expected operating temperature.

Colder <

32°F

_- Warmer

5W30

 

SAE 30

NOTE: Although multi-viscosityoils (5W30, 10W30, etc.) improve starting in cold weather, these multi- viscosity oils will result in increased oil consumption when used above 32°F. Check your oil level more frequently to avoid possible engine damage from running low on oil.

•Use engine oil provided. Remove oil fill dipstick. See figure 13. With chipper-vacuum level, use a funnel to fill engine with oil to FULL mark on dipstick.

Capacity is approximately 26 ounces. Be careful not to overfill. Oil bottle provided contains 27 oz. of oil. Tilt chipper-vacuum toward the left (from behind the hopper), then re-level. Check oil level. Refill to FULL mark on dipstick if necessary. Replace dipstick and tighten.

Oil

Fill

Dipstick

Oil

Drain

FIGURE 13.

GAS

•Remove fuel cap and fill fuel tank with approxi- mately 1 gallon of clean, fresh, lead-free grade automotive gasoline. DO NOT use Ethyl or high octane gasoline. Be certain container is clean and free from rust or foreign particles. Never use gaso- line that may be stale from tong periods of storage in the container. Replace fuel cap.

1/'2INCH OF TOP OF FUEL TANK TO

_L WARNING: DO NOT FILL CLOSER THAN

PREVENT SPILLS AND TO ALLOW FOR

FUEL EXPANSION. IF GASOLINE IS ACCIDENTLY SPILLED, MOVE CHIPPER- VACUUM AWAY FROM AREA OF SPILL.

AVOID CREATING ANY SOURCE OF IGNITION UNTIL GASOLINE VAPORS HAVE DISAPPEARED.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Horsepower Mulching and Bagging CHIPPER-VACUUM Inted in U,S.A 770-8894KOperationpractices PERSONALINJURYWHENYOUSEETHISSYMBOL.-- Reeditswafining11,CHILDREN SAF Maintenance Agreement WarrantyProduct Specifications Full ONE Year Warranty on Craftsman GAS CHIPPER-VACUUMTable of Contents TOREMOVECHIPPER-VACUUMFROMCARTON Assembly InstructionsTools Required for Assembly Howto SET-UPYOUR CHIPPER-VACUUMFigu RE Clutch Cable AdjustmentAttaching the Chipper Chute Attaching the Clutch CableKnow Your CHIPPER-VACUUM Installing the Shift KnobAttaching the BAG HOW to USE Your CHIPPER-VACUUM Meets Ansi Safety StandardsTo Stop Engine OIL Gasand OIL FILL-UPTo Empty BAG GASTo Stop Engine To StartengineFull Choke Off Position Lever General Recommendations Customer ResponsibilitiesCHIPPER-VACUUM EngineSpark Plug AIR CleanerClean Engine MufflerRemovingtheflailscreen Before Performing ANY ADJUST+ Ments or RepairsStorage CHIPPER-VACUUMScrews Flail Screen Hex Bolts Hex NutsFrame Cover Clutch CableadjustmentShift ROD Adjustment Fcti IEng Bracket Self-Tapping Screws Nail CarburetoradjustmentEnginespeed Support Stop Bolt BracketProduct 9 H.P. Chipper-Vacuum Model Number Engine Model no Trouble ShootingHOW to Order Replacement Parts Part Number Part Description649-0008 714-0104629-0241 681-0078 710-1273736-0247 711-0833A710-0230 Sears Craftsman 9 H P CHIPPER,VACUUM Model no 247,799640 Chain Differential Assy Comp Bearing ASSY-FRICTIONSprocket HUB Wheel Sprocket717-1358 717-1437 T0T101 305119 281282Oil Drain Extension Cylinder InclDowel Pin Extension CapOptional 35446Instruction Decal Spark Arrester590681 Parts List for Recoil StarterParts List for Recoil Starter Optional Starter Rope 98 x 9/64 DiaMdJ Cylinder Number Cylinder I.D Seal KITUSE Extreme Caution During Next Step

79964 specifications

The Craftsman 79964 is a versatile and efficient piece of equipment that stands out in the realm of lawn maintenance tools. This model combines power, durability, and user-friendly features, making it an excellent choice for both professional landscapers and homeowners alike.

One of the main features of the Craftsman 79964 is its robust 27cc 2-cycle engine. This high-performance engine is designed to deliver powerful cutting performance while remaining lightweight. The 2-cycle design offers a higher power-to-weight ratio, which means users can maneuver it easily without sacrificing performance.

The Craftsman 79964 boasts a relatively long reach, making it ideal for trimming hedges, shrubs, and other hard-to-reach areas. This tool is equipped with a 17-inch cutting path, allowing users to cover more ground quickly and efficiently. The trimmer head also features an auto-feed line system, ensuring that the cutting line is replenished effortlessly as it wears down, minimizing downtime.

Durability is another key characteristic of the Craftsman 79964. Its construction includes sturdy materials designed to withstand the rigors of outdoor use. The curved shaft design provides optimal balance and control, reducing user fatigue during extended use. Additionally, the ergonomic handle ensures comfortable grip and maneuverability, which enhances the overall user experience.

The Craftsman 79964 incorporates advanced technology to improve operational efficiency. Features such as the Easy Start system allow for effortless ignition with minimal effort. This ensures that users can get their tasks done without the hassle of dealing with hard-to-start engines.

Safety is also a primary focus with the Craftsman 79964. The built-in safety guard protects users from debris while operating the trimmer, maintaining a safer working environment. Moreover, the lightweight design contributes to ease of use, making it accessible for individuals of varying skill levels.

In conclusion, the Craftsman 79964 is a powerful, durable, and user-friendly trimmer that is ideal for a variety of landscaping tasks. With its efficient engine, innovative features, and strong safety measures, it stands out as a reliable choice for anyone looking to maintain a pristine outdoor space. Whether you're tackling small yard projects or large landscaping jobs, the Craftsman 79964 offers the performance and reliability needed to get the job done efficiently.
Top Page Image Contents