Craftsman 247.77588O owner manual Hopper, ChipperChute, Loose Parts, Unpacking from Carton

Page 5

Discharge Chute

Hopper*

Bottle

of Oil

ChipperChute

Safety

Glasses

Catcher Bag

*The hopper is packed in the top insert in your chipper-shredder carton.

Figure 1

Remove all loose parts includingowner's manual. See figure 1.

Roll chipper-shredderout of the canon.

Make certainall parts and literaturehave been removedbefore the cartonis discarded.

LOOSE PARTS

(Refer to figure 1.)

a, Hopper Assembly

b.DischargeChute

c.Chipper Chute

d.Catcher Bag

e.Bottle of Oil

f.Safety Glasses

g.Owner'sManual (not shown in figure 1)

TOOLS REQUIRED

1.1/2"or AdjustableWrenches

2.7/16" or AdjustableWrenches

3.9/16" or AdjustableWrenches

4.Funnel

DISCONNECTING SPARK PLUG

Disconnect the spark plug wire and move it

away from the spark plug before assemblingthe

chipper-shredder. See figure 2.

Spark PlugWire

IMPORTANT: This unitis shippedwithout gasoline or oil in the engine, Al_erassembly, see OPERATION sectionof this manual for proper fuel and engine oilfill-up.

NOTE: To determine rightand left hand sides of your chipper-shredder, stand behind the unit with the engine farthest away from you.

Yourchipper-shredderhasbeen completelyassembled at the factory, exceptforthe hopperassembly,chipper chute,discharge chuteand the catcherbag.

These parts are shippedloosein the carton. A pairof safety glasses and a bottle ofoil are also includedin the canon.

UNPACKING FROM CARTON

Cut the corners of the canon.

Remove all packing inserts.

Figure 2

ATTACHING DISCHARGE CHUTE

Remove the wing knobs from each side of the discharge opening on the chipper-shredder.See figure 3.

Using two 7/16" wrenches, remove hex locknut, two spacers, and the bex bolt fromtop of the housingassembly. For easy assembly,do not remove the second spacer from the hex bolt. Place the discharge chute in positionon the dischargeopening. Inserthex boltand spacer

Image 5
Contents Craftsman Tow HitchKit Product SpecificationEngine To cause cancer, birthdefects or other reproductiveharm General OperationImpellertocometoacompletestopTheimpeller ServiceChildren Your ResponsibilityChipperChute HopperLoose Parts Unpacking from CartonSpacer-J-Hinge Attaching Hopper AssemblyAttaching the Catcher BAG Attaching the Chipper ChuteOperating Controls Meets Ansi Safety StandardsStarting Engine GAS and OIL FILL-UPOil Packed with unit Add oil if necessary. Replace dipstickStopping Engine Using Your CHIPPER-SHREDDERTo lowerthe hopper assembly, use one handto Engine Maintenance CleaningChangesbecomesstdngy,etc. or if the rate at which General RecommendationsCustomer Responsibilities Lubrication Ifnecessary,replacepaper filterdo not attemptAvoid these areas Spark Plug MufflerPage Sharpening or Replacing Blades Removing the Flail ScreenHex Nut Washer Hand Knobs Chipper BladesAdjusting Carburetor Disconnectsparkplug wire and move it awayTires Engine SpeedEngine CHIPPER-SHREDDEROther SeasonContactyourSEARS service center Serviceaircleaner Loss of power operationerraticEnginefailstostart Fueltankempty,orstalefuelModel Sears Craftsman 8.5 H.P. CHIPPER-SHREDDERKey PartNo No 53 714-0149B 57 781-0510B 770-1228A 11480 681-0118 681-0144 710-0542757 RPM Low 21132 Carburetor ¢p-.4 Sears