Craftsman 917270841 owner manual Belt Removal, Tolevel Mower Housing, SIDE-TO-SIDE Adjustment

Page 23

TOLEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway° Make sure tires are properly inflated (See =PROD-

UCT SPECIFICATIONS"). If tires are over or undednflated, you will not properly adjust your mower°

SIDE-TO-SIDE ADJUSTMENT

o Raise mower to its highest position°

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance =A" on both sides of mower should be the same or within 1/4" of each other,

o If adjustment is necessary, make adjust- ment on one side of mower only.

°To raise one side of mower, tighten lift link adjustment nut on that side_

°To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

o Recheck measurements after adjusting.

,,Before making any necessary adjust- ments, check that both front links are

equal in length. Both links should be approximately 10-3/8"o

o If links are not equal in length, adjust one link to same length as other link.

o To lower front of mower loosen nut "E"

on both front links an equal number of tums.

o When distance "D" is 1/8" to 1/2" lower at front than rear, tighten nuts "F" against trunnion on both front links.

=To raise front of mower, loosen nut "F" from trunnion on both front tinks.

Tighten nut "E" on both front links an equal number of turns.

=When distance "D" is 1/8" to 1/2" lower

at front than rear, tighten nut "F" against trunnion on both front links.

o Recheck side-to-side adjustment.

Mandrel

Bottom

 

 

Bottom

 

Edge of

r-

_

Edge of

 

Mower to _-_

_ 'l

if _ ,f_-_

/ Mower to

 

Or°un0/l....

.....V

Both Front Links Should be Equal in Length

 

 

 

 

 

Nut "F"

 

Lift Link Adjustment Nut

 

 

FRONT-TO-BACK ADJUSTMENT

Trunnion _

_.

 

IMPORTANT: Deck must be level side-to-

side. If the following front-to-back adjust-

Front Links

ment is necessary, be sure to adjust both

front links equally so mower will stay level side-to-side.

To obtain the best cutting results, the mower housing should be adjusted so that

the front is approximately 1/8" to 1/2" lower than the rear when the mower is in

its highest position.

Check adjustment on right side of tractor. Measure distance "D" directly in front and behind the mandrel at bottom edge of mower housing as shown.

TO REPLACE MOWER BLADE DRIVE BELT (See Illustration Next Page)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL-

oRemove mower from tractor (See "TO REMOVE MOWER" in this section of

this manual).

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Sears Craftsman Help Line Lawn TraotoLimited 90 DAY Warranty on Battery Limited TWO Year Warranty on Craftsman Riding EquipmentTragic accidents can occur if the operator ServiceSlope Operation Do notGrass can hide obstacles Customer Responsibilities Lock Washers 1/4 Parts BAG Contents Shown Full SiZE Attach Steering Wheel Tools Requiired for AssemblyTo Remove Tractor from Carton Unpack CartonCheck Tire Pressure HOW to SET UP Your TractorConnect Battery Check for Proper Position ALL BeltsFollowing Important Items Check Brake SystemTo Convert to Bagging or Discharging Please Review the FollowingBattery Reverse Forward Fast Slow Know Your Tractor Controlled by the motion control lever HOW to USE Your TractorThrottle Control To Move Forward and BackwardTo Transport To Operate on HillsBefore Starting the Engine PositionTo Start Engine ADD GasolineCedure with the motion control lever Three 3 times Purge TransmissionPage Bearing Zerk Check brake operation o Check tire pressureFront @ Front WheelBlade Removal BatteryBrake Operation TiresTo Change Engine OIL Transaxle CooungCooling Transaxle Pump FluidOn page 5 of this manual NN-LBNEFUEL Filter Engine Cooling FinsPlugs Right side of tractor CleaningAll gasoline, oil, etc To Remove MowerBelt Removal Tolevel Mower HousingSIDE-TO-SIDE Adjustment FRONT-TO-BACK AdjustmentStopping distance at high speed in high Belt InstallationTo Adjust Brake Brake system which is mounted on the side of the transaxleFront Wheel TOE4N/CAMBER To Adjust Motion Control LeverTo Adjust Steering Wheel ALIGN- Ment To Start Engine That has a Weak BatteryTo Replace Fuse TeriesPositive Terminal To Replace Headlight BulbEngine To Remove Hood and Grill ASEngne Fuel System BatteryAcceleration Test TractorCorrection HousingLoose Chart Cause TroubleshootingPage Page Tractor - Model Number O11ioElectrical TRACTOR- Model NumberElectrical KEY Part Tractor - Model Number Chassis and Enclosures KEY Part Description 100 105 Tractor - Model Humber Ground Drive5751 Description Tractor - Model Number 917=270641 Ground DriveTractor --MODEL Humber Steering Asseubly 74780520 Tractor --MODEL Number Steering AssemblyOptional Equipment 31 109202X Tank Fuel 1 25 Fr ElbowStd 90 Degree 3/818 NptWasher Lock Ext Tooth3/8 Shield Browning/DebrisGuard1343OO TRACTOR- Model Number Seat AssemblySTD541437 11 12OO68X163205 Decals KEY Part DescriptionWheels & Tires 273832Tractor - Model Number Lift Assembly 73680800 Tractor -- Model Number Lift Assembly103 72110610 Arm Assembly,Pad, BrakeBolt, Shoulder 5/16-18 UNC 133943Tractor -- Model Number Hydro Transaxle - Model Number Hydro TRANSAXLE-- Model Number 166 230635337 294 1029 1026164 127 138 106 987 ,11, T 105 51142Valve Overhaul KIT Carburetor Overhaul KIT CARBURE-IORGASKET s-r 20 634A 842 524 868 868A 523171535 Gasket SET503 Tractor - Model Humber482 209 783 801 728 615 802394358 Filter, Fuel In Fuel Une NO. no94905 232758 Page Suggested Guide for SiGHTiNG Slopes for Safe Operation 800-473o7274 Para pedir servicio de reparacibn a Para ordenar piezas con entrega a domicilio

917270841 specifications

The Craftsman 917270841 is a versatile and efficient riding lawn mower, designed for both residential and commercial use. Whether you're maintaining a large lawn or tackling more extensive landscaping tasks, this mower is equipped to handle a variety of conditions while ensuring a precise cut.

One of the main features of the Craftsman 917270841 is its powerful engine. With a 24 HP Briggs & Stratton single-cylinder engine, users can expect robust performance and reliable starting, even in challenging weather conditions. The engine's design ensures optimal power and efficiency, making mowing through thick grass or hilly terrain a breeze.

Another significant characteristic of the Craftsman 917270841 is its cutting deck. The mower boasts a 54-inch cutting deck, which allows for faster mowing times and fewer passes across your lawn. The deck features multiple cutting heights, adjustable from 1 to 4 inches, giving users the flexibility to achieve the perfect length for their grass types and preferences. The addition of a washing port simplifies maintenance, allowing for easy cleaning of the deck after use.

The mower is equipped with advanced technologies aimed at enhancing user experience and comfort. One of these features includes a tight turning radius, enabling agility around landscaping obstacles, trees, and flower beds. The ergonomic seating and adjustable controls also contribute to a more comfortable ride, reducing operator fatigue during long mowing sessions.

Safety is a priority with the Craftsman 917270841, incorporating features like automatic blade stop technology that halts the blades when the operator leaves the seat, preventing accidents. Additionally, the robust build ensures durability, meaning users can rely on this mower to perform season after season.

In summary, the Craftsman 917270841 riding lawn mower combines powerful performance, a large cutting deck, adjustable heights, and user-friendly technologies, making it an ideal choice for anyone looking to maintain a beautiful and healthy lawn efficiently. Whether for personal use or commercial landscaping, this mower offers reliability and effectiveness that homeowners and professionals alike can appreciate.
Top Page Image Contents