Craftsman 917.385192 owner manual Lawn Mower, Grass Catcher

Page 12

LAWN MOWER

Always observe safety rules when per- forming any maintenance.

TIRES

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

BLADE CARE

For best results, mower blade must be kept sharp. Replace a bent or damaged blade.

CAUTION: Use only a replacement

blade approved by the manufacturer of your mower. Using a blade not approved

by the manufacturer of your mower is hazardous, could damage your mower and void your warranty.

TO REMOVE BLADE

1.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

2.Turn lawn mower on its side. Make sure air filter and carburetor are up.

3.Use a wood block between blade and

mower housing to prevent blade from turning when removing blade bolt.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

4.Remove blade bolt by turning counter- clockwise.

5.Remove blade and attaching hardware (bolt, lock washer, hardened washer).

NOTE: Remove the blade adapter and check the key inside hub of blade adapter. The key must be in good condition to work properly. Replace adapter if damaged.

TO REPLACE BLADE

1.Position the blade adapter on the en- gine crankshaft. Be sure key in adapter and crankshaft keyway are aligned.

2.Position blade on the blade adapter aligning the two (2) holes in the blade with the raised lugs on the adapter.

3.Be sure trailing edge of blade (opposite

sharp edge) is up toward the engine.

4.Install the blade bolt with the lock washer and hardened washer into blade adapter and crankshaft.

5.Use block of wood between blade and

lawn mower housing and tighten the blade bolt, turning clockwise.

• The recommended tightening torque is 35-40 ft. Ibs.

IMPORTANT: Blade bolt is heat treated. If bolt needs replacing, replace only with approved bolt shown in the Repair Parts section of this manual.

Blade adapter

Ke_

Crankshaft

 

 

keyway

Lockwasher

 

 

Blade

 

 

Blade

bolt Hardened

washer Trailing edge Crankshaft

TO SHARPEN BLADE

NOTE: We do not recommend sharpening

blade - but if you do, be sure the blade is

balanced. An unbalanced blade will cause eventual damage to mower or engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, drive a nail into a beam or wall. Leave about one inch of

the straight nail exposed. Place center hole of blade over the head of the nail.

If blade is balanced, it should remain in

a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

GRASS CATCHER

(If purchased as an accessory)

•The grass catcher may be hosed with water, but must be dry when used.

•Check your grass catcher often for dam-

age or deterioration. Through normal use it will wear. If catcher needs replac- ing, replace only with approved replace-

ment catcher shown in the Repair Parts section of this manual. Give the lawn

mower model number when ordering.

ENGINE

LUBRICATION

Use only high quality detergent oil rated with API service classification SG-SL. Select the

oil's SAE viscosity grade according to your expected operating temperature.

 

 

 

SAE

VISCOSITY

GRADES

 

 

 

 

t

F

-20

 

0

30

32 40

60

80

 

100

 

/

i

 

 

i

 

 

 

i

i

 

i

 

C -30

 

-2_0

-10

 

0

1_0

20

30

 

40

 

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Craftsman Maintenance Schedule Sears Service Back Cover Year Full Warranty on Craftsman Lawn MowerDo not IV. Safe Handling of GasolineAPI SG-SL SAE RJ19HXRepair Protection Agreements To Install Attachments To Remove Mower from CartonTo Unfold Handle LiftMeets Cpsc Safety Requirements OperatorHOW to USE Your Lawn Mower Engine Speed To Adjust Cutting HeightEngine Zone Control Before Starting Engine ADD OILTo Stop Engine To Start EngineADD Gasoline Mowing Tips Mulching Mowing TipsGeneral Recommendations Before Each USELubrication Lawn Mower Grass CatcherMuffler Lawn Mower To Adjust Cutting Height To Adjust HandleSqueeze To Adjust Rear DeflectorEngine Speed CarburetorHandle Squeeze To FoldProblem Cause Correction Engine OILCylinder OtherProblem Need More HELP?Loss Poor23-26 Operacion HacerNo Hacer SERVlClO SG-SL SAERendimiento DE LA Segadora Acuerdos de Protecci6nPara Remover LA Segadora DE LA Caja DE Carton Para Instalar LOS AccesoriosFamiliaricese CON SU Segadora Cumple CON LOS Requisitos DE Seguridad DE LA CpscPara Convertir LA Segadora MotorFijar EL Cartucho DEL Tapon DEL Carburante Agregue GasolinaPara Parar EL Motor Para Hacer Arrancar EL MotorOnsejos Para Segar Consejos Para Segar Y ACOL- CharRecomendaciones Generales Antes DE Cada USOLubricacion Segadora LlantasCuidado DE LA Cuchilla Motor LubricacionLiivipieza Filtro DE AireSegadora Para Ajustar LA Altura DE Corte Proteccion Contra LA DescargaPara Ajustar EL Mango Motor Velocidad DEL Motor AdelanteMango Motor Sistema DE CombustibleOtros SearsProblema Page Oo co Replacement Engine Engine Gasket SET 957 592 689 597KEY Part Description KEY Part NO. NO. Description Your Home Our Home

917.385192 specifications

The Craftsman 917.385192 is a reliable and efficient lawn tractor that offers a combination of power, durability, and ease of use for homeowners looking to maintain their lawns with minimal effort. With a robust design and a range of features, this machine is highly regarded among gardening enthusiasts and professionals alike.

At the heart of the Craftsman 917.385192 is a powerful 19.5 horsepower Briggs & Stratton engine. This engine delivers adequate power to tackle a variety of mowing tasks, ensuring that users can easily cut through thick grass and tough terrains. Its 42-inch cutting deck allows for efficient mowing, as it covers a wide area in a single pass, saving time during lawn maintenance.

One of the standout features of the Craftsman 917.385192 is its versatile cutting height adjustment system. With six different cutting height settings, users can easily customize the length of their grass according to their preferences and the changing seasons. This flexibility ensures a clean and professional-looking finish every time.

The tractor's hydrostatic transmission provides a smooth and seamless driving experience, allowing for easy maneuverability around corners and obstacles. This technology eliminates the need for shifting gears, allowing users to focus on the mowing task at hand without any interruptions.

Comfort and convenience are also key elements of the Craftsman 917.385192. The tractor is equipped with an adjustable high back seat that offers ample support during lengthy mowing sessions. Additionally, the easy-to-reach controls are intuitively designed, ensuring that even novice users can operate the machine with confidence.

Safety features are paramount in the design of this lawn tractor. The Craftsman 917.385192 includes a safety ignition switch and a blade brake system, ensuring that the mower stops immediately when the operator leaves the seat. This provides peace of mind, particularly when mowing on slopes or uneven terrain.

In summary, the Craftsman 917.385192 is an exceptional lawn tractor that combines power, versatility, and safety in a user-friendly package. With its robust engine, adjustable cutting heights, hydrostatic transmission, and comfortable design, it stands out as an excellent choice for maintaining a beautiful and healthy lawn. Whether for residential or light commercial use, this lawn tractor is sure to meet the needs of any user, making lawn care a more enjoyable and efficient task.
Top Page Image Contents