Craftsman 917.379480 owner manual Lawn Mower, Handle, Fuelsystem, Engineoil, Cylinder

Page 16

Immediately prepare your lawn mower for storage at the end of the season or if the unit will not be used for 30 days or more.

LAWN MOWER

When lawn mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

Clean entire lawn mower (See "CLEANING" in the Maintenance

"section of this manual).

Lubricate as shown in the Maintenance section of this manual.

Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

Touch up all rusted or chipped paint

surfaces; sand lightly before painting.

HANDLE

You can fold your lawn mower handle for storage.

Squeeze the bottom ends of the lower handle toward each other until the lower handle clears the handle bracket, then move handle forward.

Loosen upper handle mounting bolts enough to allow upper handle to be folded back.

IMPORTANT: When folding the handle for storage or transportation, be sure to fold the handle as shown or you may damage the control cables.

When setting up your handle from the storage position, the lower handle will

automatically lock into the mowing

.position.

Lower handle

Handle bracket

Squeeze to fold

Hairpin cotter

Operator presence control bar

 

Upper Handle -_

//,,,._P_)_

Fold

_/_'_----_

,"_

forward for

__.__,_';;'_'/J

 

storage

__,

,J_

Fold

 

 

\

backward

 

"__

Mowing

Lower handle

position

ENGINE

FUELSYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel

filter, fuel hose, or tank during storage.

Also, experience indicates that alcohol

blended fuels (called gasohol or using ethanol or methanol) can attract moisture

which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

Drain the fuel tank.

Start the engine and let it run until the fuel lines and carburetor are empty.

Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run

engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach

the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINEOIL

Drain oil (with engine warm) and replace with clean engine oil. (See "ENGINE" in

the Maintenance section of this manual).

CYLINDER

Remove spark plug.

Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

Pull starter handle slowly a few times to distribute oil.

16 Replace with new spark plug.

Image 16
Contents Craftsman SEARS, Roebuckand CO., D/817 WA, Hoffman ESTATES, Illinois TrainingPreparation Maintenance and Storage OperationTo Remove Lawnmower from Carton Lawn Mower MaintenanceLawn Mower Performance To Install Attachments To Unfold HandleMeets Cpsc Safety Requirements Nowyour Lawn MowerTo Adjust Cutting Height Engine SpeedChoke To Attach Grass CatcherDrive Control Before Starting Engine OILADD Gasoline To Start EngineMowing Tips Maintenance Lubrication ChartGeneral Recommendations Before Each USELawn Mower Engine Grass CatcherDrive Wheels Gear CaseCleaning Clean Under Drive CoverMuffler AIR FilterTo Adjust Handle Lawn Mower To Adjust Cutting HeightRear Deflector To Removfjreplace Drive BeltEngine CarburetorLawn Mower HandleFuelsystem EngineoilTroubleshooting Chart Problemcause CorrectionTroubleshooting Chart Problem CausePage Rotary Lawn Mower --MODEL no Gear Case Assembly Part Number KEY Part DescriptionRotary Lawn Mower MODEL.NUMBER Rotary Lawn Mower Model Number KEY Part NO. noRotary Lawn Mower Model Number 751152 158755 146527 150495 150182 145212 11 15O340 Honda 4-CYCLE Engine Model NO. GCV160-A1A Flywheel Recoil Starter AIR Cleaner Honda 4-CYCLE Engine Model NO. GCV160-A1A Camshaft Pulley KEY Part NO. NO.DESCRIPTION Control KEY Part DescriptionCarburetor KEY Part NO. NO.DESCRIPTION AIR Cleaner KEY Part Description Honda 4-CYCLE Engine Model NO. GCV160-AIAFAN Cover KEY Part NO. no Flywheel KEY Part NO. noHonda 4-CYCLE Engine MY-HOMEsAnytime, dayor night