Craftsman 358.35181 Braking function control, Inertia activating function control, Operating Tips

Page 10

CHAINBRAKE

_b'WARNING:

If the brake band is

worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not

stop the chain. The chain brake must be replaced if any part is worn to tess than 0.020" (0.5 ram) thick. Repairs on a chain brake should be made by your Sears Service Center. Take your unit

to the piace of purchase or to the near- est Sears Service Center.

•This saw is equipped with a chain

brake. The brake is designed to stop the chain if kickback occurs.

•The inertia-activated chain brake is activated if the front hand guard is pushed forward, either manually (by hand) or automatically (by sudden movement).

•If the brake is already activated, it is disengaged by puiting the front hand guard back toward the front handle as far as possible.

•When cutting with the saw, the chain brake must be disengaged.

Braking function control

CAUTION: The chain brake must be

checked several times daily. The en- gine must be running when performing

this procedure. This is the onIy instance when the saw shouid be

placed on the ground with the engine running.

Place the saw on firm ground. Grip the rear handle with your right hand and the front handle with your left hand. Apply futt throttle by fully depressing the throttle trigger. Activate the chain brake by turning your left wrist against the hand guard without releasing your grip around the front handle. The chain shoutd stop immediately.

Inertia activating function control

_kWARNING: When performing

the foitowing procedure, the engine must be turned off.

Grip the rear handte with your right hand and the front handle with your teft hand.

Hotd the chain saw approximately 14 inches (35 cm) above a stump or other wooden surface. Reiease your grip on the front handle and use the weight of the saw to let the top of the guide bar fall forward and contact the stump. When the tip of the bar hits the stump, the brake should activate.

OPERATING TIPS

•Check chain tension before first use and after 1 minute of operation, and

each time before you start the chain saw. See CHAIN TENSION in the

MAINTENANCE section.

•Cut wood only. Do not cut metaI, plas- tics, masonry, non-wood building ma- terials, etc.

•Stop the saw if the chain strikes a foreign object. Inspect the saw and repair or replace parts as necessary. If the chain jumps off the guide bar, inspect the chain for damaged drive links before reinstalling. Burrs on drive links, which prevent them from

entering the groove of the guide bar, can be removed with a flat rite.

•Keep the chain out of dirt and sand. Even a smaII amount of dirt will dull a

chain, increase the possibility of kick- back, and require chain sharpening or replacement.

•Practice cutting a few small logs us- ing the following techniques to get the "feeF of using your saw before you begin a major sawing operation.

•Squeeze the throttIe trigger and allow the engine to reach full speed before cutting.

•Begin cutting with the saw frame against the log.

•Keep the engine at full speed the entire time you are cutting.

•Altow the chain to cut for you. Exert onty light downward pressure, tf you force the cut, damage to the bar, chain, or engine can result.

•Release the throttle trigger as soon as the cut is completed, allowing the engine to idle. Ifyou run the saw at full throttle without a cutting toad, unnecessary wear can occur to the chain, bar, and engine. To maxi- mize operating efficiency, do not

run the engine for longer than 30 _econd_ at a time at full throttle.

•To avoid losing control when cut is

complete, do not put pressure on saw at end of cut.

•Stop the engine before setting the saw down after cutting.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Gasoline Chain SAW ONE Year Full Warranty on Craftsman GAS Chain SAW Plan AheadHandle Fuel with Caution Carburetor AdjustmentMaintain Your SAW in Good Working Order Guard Against KickbackAvoid Pinch-Kickback Reduce the Chance KickbackAvoid Putl-ln Chain Brake WE do not REPAssembly Carton ContentsModel Chain Tension ON/STOP SwitchCHOKE/FAST Idle Lever Primer BulbStopping Your Engine Guide BAR and Chain OILFueling Engine Starting PositionStarting a Warm Engine Difficult Starting or 8tatting a flooded engineInertia activating function control Braking function controlOperating Tips Notch CUT and Felling the Tree Tree Felling TechniquesFelling Large Trees Hinge holds tree on stump and helps control fallImportant Points Bucking Using a LOG or Support StandCutting a Fallen Tree Bucking Types of Cutting Used for BuckingLimbing Using a support standLimbing and Pruning Iiwarning PruningResponsibilities Check Chain Sharpness Hand tighten onlytCheck Guide BAR Check Chain Brake Clean AIR FilterInspect and Clean Unit and Decals Check Fuel Mixture LevelTool8 required Chain Replacement To Replace ChainLoosen Chain AdjustmentJustment Engine Seasonal StorageFuel System OtherTrouble Cause Troubleshooting TableRemedy Trouble RemedyWhat is Covered Repair or Your Warranty RightsOff-road engine is purchased. Length of Coverage This war MAINTENANCE, Replacement and Repair Repair Parts Sears CHAtNSAW Model

358.35181 specifications

The Craftsman 358.35181 is a reliable and versatile gas-powered string trimmer designed for both homeowners and professionals looking to maintain their yards and gardens. This robust tool is well-regarded for its efficiency, ease of use, and advanced features, making it an excellent choice for tackling weeds, grass, and overgrown areas.

One of the standout features of the Craftsman 358.35181 is its powerful 25cc 2-cycle engine. This engine delivers a strong performance, allowing users to trim and edge with ease. It is designed to provide effective cutting while minimizing fuel consumption, ensuring that users can work longer without frequent refueling. The quick-start technology associated with this engine allows for easier starting, even in cold conditions, which is particularly beneficial for those who live in regions with varying climates.

Equipped with a 17-inch cutting width, the Craftsman 358.35181 enables users to cover more ground in a single pass, making yard maintenance quicker and more efficient. The trimmer features a dual-line bump head, allowing for easy line advancement with a simple tap on the ground. This feature saves time and effort, so users can focus on the task at hand without wasting precious minutes.

Another notable characteristic of the Craftsman 358.35181 is its lightweight design. Weighing in at around 10.5 lbs, it is manageable for extended periods of use without causing excessive fatigue. The ergonomically designed handle offers comfort and control, enabling precision in trimming along edges and around delicate landscaping.

The Craftsman 358.35181 also comes with a variety of attachments that enhance its functionality. These versatile attachments can transform the trimmer into multiple yard maintenance tools, including a cultivator, blower, or pole saw, which extends the usability of the device.

Safety features such as the protective guard and throttle control contribute to an overall secure operation when using the device. Craftsman's commitment to durability means the trimmer is constructed with high-quality materials designed to withstand the rigors of regular use.

Overall, the Craftsman 358.35181 stands out as a reliable and efficient string trimmer that combines power, performance, and versatility, making it an excellent addition to any homeowner or professional landscaper's tool collection. Whether for maintaining a small garden or tackling larger projects, this trimmer is ready to meet the challenge.
Top Page Image Contents