Craftsman 536.772301 manual Storage, Edger

Page 21

SERVICE AND ADJUSTMENT

STORAGE

Edger indoors with fuel in the

_1_ WARNING: Never store the fuel tank. Never store in an en-

closed, poorly ventilated area where fumes could reach an open flame, a spark or a pilot light as on a furnace, wa- ter heater or clothes dryer.

oline while inside a building,

_lbARNING: Do not remove gas- near a fire, or while you smoke.

Gasoline fumes can cause an explosion

or a fire.

When the Edger is put in storage for thirty days or more, follow the steps below to make sure the Edger is in good condition the following season.

Edger

Completely dean the Edger.

Check the Edger for worn or damaged pads. Tighten all loose hardware.

Apply a smatI amount of engine oil to all moving parts, particularly the wheels.

Put the Edger in a building that has good ventilation.

Cover the Edger with a suitable protec- tive cover that does not retain moisture.

Do not use plastic.

IMPORTANT: Never cover the Edger while the engine and exhaust areas are still

warm.

NOTE: A yearly checkup or tune-up by a Sears Service Center is a good way to make sure that your Edger will provide

maximum performance for the next sea- son.

Engine

IMPORTANT: It is important to prevent gum deposits from forming in fuel system

parts such as the carburetor, fuel filter, fuel hose, and tank during storage. Also,

using alcohol-blendedfuels (called gaso- hol, ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an en- gine while in storage.

To prevent engine damage when the Edger is in storage for 30 days or more, follow the steps below:

Let the engine run until it is out of gaso- line.

If you do not want to remove the gaso- line, add a fuel stabilizer to any gasoline Ieft in the fuel tank. A fuel stabilizer will minimize gum deposits and acids. If the fuel tank is almost empty, mix the fuel stabilizer with fresh gasoline in a sepa- rate container and add the mixture to the

fuel tank. Always follow the instructions on the stabilizer container. Start the en-

gine. Let the engine run for 10 minutes to allow the mixture to reach the carbu- retor.

Change the engine oil. See "How To

Change The Engine Oil" in the Mainte- nance section.

Lubricate the piston/cylinder area. This can be done by first removing the spark plug and squirting a small amount of clean engine oil into the spark plug hole. Then, cover the spark plug hole with a rag to absorb oil spray. Next, rotate the engine by pulling the starter two or three times. Finally, install the spark plug and attach the spark plug wire.

Store the Edger in the operating position with the wheels down. If the Edger is stored in any other position, oil from the crankcase will enter the cylinder and cause a service problem.

F-001102M21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents F01102M Model noContents Safety Rules Fuel SafetyBefore Use Repair / Adjustments Safety SafetyRules Safe StorageSlow Fast Fuel Primer ButtonWear Eye Protection Before Operating This Machine Assembly AssemblyParts Packed Separately In Carton HairPin Container of OilHOW to Raise the Handle How To Fill With Gasoline HOW to Prepare the EngineFill With Oil Oil RecommendationsChecklist Know Your Edger OperationEYE Protection EngineHOW to USE Throttle Control HOW to Stop the EdgerPrimer Button Edger unattended while Engage the cutting blade and stopRunning, never leave the Edger HOW to USE the Index LeverHOW to USE the CURB-HOPPING Feature Wheel until the front wheel is level withFront Wheel HOW to Start the Engine HOW to Stop the EngineIndoors or in a poorly ventilated Parts. Avoid the muffler and surroundEdging Tips Product Specifications MaintenanceCustomer Responsibilities General RecommendationsHow To Change The Engine Oil LubricationHowto Changethe AIR Filter Spark Plug Carburetor AdjustmentHOW to Remove the Belt Service and AdjustmentHOW to Replace the Blade Edger StorageTrouble Cause Correction Trouble Shooting ChartKEY Description Partno Craftsman 536.772301REPAIR PartsKEY NO. Description Repair PartsNut,5/16-18 331076-848Knob,Rectangle FrontWheelArm 339299-848FrontCurbHopper 740132 Flatwasher 22265Screw,5/16-18x.75 KEY Partno DescriptionKnob,Wing5/16-18 Bolt,5/16-18x2.00330 331 329 KEY Description 740147 725782585 Screw,5/16-18x1.2551887 Spacer,Sleeve 310715310716 Tire& Rim 336546Return Spring CraftsmanFuel Fitting Float ShaftOO1102M32 KEY Part Description Repair 890732 Starter No optional Tabla DE Localizacion DE GARANTiASiMBOLOS GARANTiA Limitada DE DOS Aiios Para LA Orilladora CraftsmanPasos preliminares Normas DE SeguridadCombustible OperacibnReparacion / Ajustes AlmacenamientoMarcha lenta Marcha rapida Combustible Aceite Botbn cebador SiMBOLOS InternacionalesMontaje EnsamblajeInstrucciones Para Sacar LA Orilladora DE SU Caja Horquilla Botella de aceiteFigura OOllO2M42 Como Levantar EL MangoPreparacion DEL Motor Cbmo Ilenar el cbrter de aceiteC6mo Ilenar el c&rter del motor con Lista DE Comprobacion Proteccion Para LOS Ojos Conozca SU OrilladoraMotor Vista DE LA CuchillaComo Usar EL Control DEL Acelerador Como Detener LA OrilladoraComo Usar EL Botcn EL Botcn Cebador Como Usar LA Palanca DEL EmbragueRecorte Como Usar LA Palanca DE ReglajeComo Usar LA Funcionalidad DE AbordilladoAfloje la perilla de la rueda delantera Como Arrancar EL Motor Como Parar EL MotorRecomendaciones Para EL USO DE SU Orilladora Buena distancia de la mquina. MantenTes giratorias clue puedan causar lesio- nes Responsabilidades DEL Usuario MantenimientoEspecificaciones DEL Producto Recomendaciones GeneralesCMO Cambiarel Filtrodeaire LubricacicnCbmo cambiar el aceite de motor Plazar inmediatamente el filtro de aire siAjuste DEL Carburador BujaComo Desmontar LA Correa Servicio Y AjustesComo Reemplazar LA Cuchilla Orilladora AlmacenamientoTabla DE Localizacion DE Averias ProblemacausasolucionNota FOO1102M59 Gggggg

536.772301 specifications

The Craftsman 536.772301 is a powerful, versatile snow blower designed to tackle harsh winter conditions. This machine combines reliability and innovative technology to ensure efficient snow clearing, making it a favorite among homeowners in snowy regions.

One of the standout features of the Craftsman 536.772301 is its robust motor. With a high-performance engine, it delivers consistent power and high torque, enabling the snow blower to handle heavy snowfall and compact snow buildup with ease. This snow blower is equipped with a 24-inch clearing width, allowing users to clear large driveways and sidewalks in fewer passes. Its powerful impeller design ensures that snow is thrown far from the path, reducing the need for backtracking.

The Craftsman 536.772301 also boasts adjustable speed settings. This feature allows users to control the pace at which they clear snow, making it easier to adapt to different snow conditions. With multiple forward and reverse speeds, operators can find the perfect balance when navigating through dense snow or maneuvering around obstacles.

Another notable characteristic is the snow blower's easy-start technology. The electric start feature helps eliminate the frustration of traditional pull starts, allowing users to start the machine at the push of a button. This is especially beneficial for those who may face difficulty starting a gas-engine machine in cold weather.

The auger and impeller system on the Craftsman 536.772301 work in tandem to break apart snow and ice efficiently, ensuring that even the toughest snow is cleared without clogging. Furthermore, the adjustable chute allows for 180 degrees of rotation, providing precise control over where the snow is directed, whether it be onto a lawn or away from sidewalks.

In terms of construction, the Craftsman 536.772301 is robust and durable. Designed to withstand harsh winter conditions, it features high-quality materials that enhance longevity. The large, deep-tread wheels offer excellent traction even on slippery surfaces, ensuring stability and safety during operation.

With its combination of power, ease of use, and thoughtful engineering, the Craftsman 536.772301 is a reliable tool for anyone looking to efficiently clear snow during winter storms. Whether it's for residential use or small commercial applications, this snow blower is built to deliver impressive results season after season.
Top Page Image Contents